All Seasons Hire Cyclone 50 User manual

Cyclone 50 2011 Page 1 of 3
© Allseasons Hire
Cyclone 50
At Allseasons Hire we take your health and safety very seriously. Please read
these operating instructions carefully before attempting to use the equipment.
If you have any concerns or queries please call us for advice FREE on 0800-
0828001
OPERATING INSTRUCTIONS
Important information
oDO NOT FLASH TEST ABOVE 1250V. PERMANENT DAMAGE WILL OCCUR
oALWAYS START THE FAN ON THE HIGHEST SPEED SETTING.
If problems are experienced, call us FREE on 0800-0828001 Maintenance
should only be attempted by competent personnel in accordance with the
instructions or supplier guidelines.
IMPORTANT!
Failure to follow these instructions could damage this equipment.
Please ensure you have read and understood these instructions fully
BEFORE attempting to operate the equipment

Cyclone 50 2011 Page 2 of 3
© Allseasons Hire
GENERAL SAFETY
oNever place anything on top of the unit and never obstruct its air inlet/outlet grills.
Leave a 300 mm gap all round the unit to let the air circulate.
oAlways switch OFF and unplug the equipment when not in use.
ELECTRICAL SAFETY
oThis fan unit plugs into either a standard 230v 13 amp or a 110v power supply,
depending on model (see Data plate for voltage type). The plug (230v models only) is
fitted with a 13 Amp fuse.
oExtension leads should be; correctly rated for the inductive load, fully unwound,
loosely coiled and never run through water or over sharp edges
oTo reduce the risk of electric shock, use a suitable RCD (residual current device)
oNever pull the equipment by its flex
oEnsure the unit and power socket are both switched OFF before plugging into the
power supply.
Set up and operation
oSet the unit up on a firm, level surface and do not site the unit close to any personnel
wearing contact lenses, sensitive to any dust movement, hay-fever sufferers etc. This
unit moves air only, but minute particles of dust/pollen etc will also be moved,
especially on highest fan setting, so careful location/fan angle/use of speed control will
require consideration
oThe body of the fan is held in position via the side-mounted hand-wheels. To adjust,
slacken the wheels to allow the fan body to be moved. Once the desired angle is
reached, ensure the hand-wheels are turned hand tight to prevent movement
oThe air-flow from the fan exits from the side with the speed controller on it (the front),
the intake side is opposite
oPlug the unit into the relevant power supply and switch the supply ON
oPress the red ‘rocker’ switch, on the front of the unit to ON, which will then illuminate
oTe fan blade should immediately start to turn & the speed can be controlled with the
knob on the control panel, turning CLOCKWISE TO INCREASE, ANTI-CLOCKWISE TO
DECREASE
oDo not force the knob past the stop point; you will damage the speed controller.
Usage and care and storage
oNever use an air mover except for its intended purpose
oKeep the equipment clean & especially the grill faces
oBlow out the grills with compressed air if ‘clogged’ up
oNever move the unit whilst it is operating!
oSwitch the unit OFF and unplug from its power supply, wrap the cable round the
storage ears.

Cyclone 50 2011 Page 3 of 3
© Allseasons Hire
Troubleshooting
PROBLEM
LIKELY CAUSE
SOLUTION
UNIT FAILS TO
OPERATE
POWER FAILURE
CHECK UNIT IS
PLUGGED IN TO
POWER SUPPLY
CHECK PLUG FUSE
(230v ONLY) FOR
FAILURE & CORRECT
13AMP RATING
CHECK SPEED
CONTROLLER FUSE
LOCATED AT REAR OF
CIRCUIT BOARD
110v MODELS, CHECK
POWER SUPPLY IS
SUITABLE FOR THE
INDUCTIVE LOAD
CHECK BUILDING RING
CIRCUIT IS NOT
OVERLOADED
POOR AIRFLOW
SPEED CONTROL ON
LOW SETTING
GRILLS DIRTY
AIR INLET GRILLS
OBSTRUCTED
TURN SPEED
CONTROL KNOB
CLOCKWISE TO
INCREASE AIRFLOW
BLOW COMPRESSED
AIR THROUGH GRILLS
TO CLEAN
REMOVE
OBSTRUCTION