Allcam PLB105 User manual

English
Installation Instruction
1
UNPACKING INSTRUCTIONS
! Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
! Check package contents against the Supplied Parts List in the next page to assure that all components were received
undamaged. Do not use damaged or defective parts.
! Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before beginning the installation, and carefully
follow all instructions contained herein. Use proper safety equipment during installation.
Please call a qualified installation contractor for help if you:
! If you don't understand these directions or have any doubts about the safety of the installation.
! If you are uncertain about the nature of your wall, consult a qualified installation contractor.
Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby
disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of
this product.
CAUTION!
WARNING
!This TV mount must be securely attached to the vertical wall. If the mount
is not properly installed it may fall, resulting in possible injury and/or
damage.
Note: The mounting components and hardware supplied in this package are not designed for installations to
walls with steel studs or to cinder block walls. If the hardware you need for your installation is not included,
please consult your local hardware store for proper mounting hardware for the application.
Tools Required 3/16" Drill Bit
Phillips Screwdriver
1/2" Masonry Bit
Stud Finder
Wrench or Socket Set
Carpenter's Level

(4)M4x12 Bolt-e (4)M5x12 Bolt-f (4)M6x12 Bolt-g (4)M8x16 Bolt-h
(4)M4x30 Bolt-i (4)M5x30 Bolt-j (4)M6x35 Bolt-k (4)M8x40 Bolt-l
(1)Wall Plate-a (1)Right Monitor Bracket-c (1)Locking Bar-d(1)Left Monitor Bracket-b
2
Supplied Par ts List
(6)Lag Bolt-u (6)Lag Bolt Washer-v (6)Concrete Anchor-w
(4)M4/M5 Space-q (4)M6/M8 Space-r (8)M4/M5 Washer-s (4)M6/M8 Washer-t
(4)M4 Lock Washer-m (4)M5 Lock Washer-n (4)M6 Lock Washer-o (4)M8 Lock Washer-p

First of all, Once you have determined the correct diameter,
please see the relative diagram as below. You will thread the Bolt into the TV using the correct Lock Washer(m,n,o,p),
Washer(s,t) and spacer(q,r). For the M4 or M5 diameter bolt, you will need another M4/M5 Washer between the Monitor
Bracket and the Spacer. Please make sure the Monitor Brackets are vertically centered and level with each other.
make sure the diameter of the Bolt(i,j,k,l) your TV requires.
First of all, make sure the diameter of the Bolt(e,f,g,h) your TV requires. Once you have determined the correct diameter,
please see the relative diagram as below. You will thread the Bolt into the TV using the correct Lock Washer(m,n,o,p) and
Washer(s,t). Please make sure the Monitor Brackets(b,c) are vertically centered and level with each other.
Mounting the Monitor Brackets to a TV with Flat Back
Step 1A
Step 1B Mounting the Monitor Brackets to a TV with Curved Back
M4 Diameter Bolt M6 Diameter Bolt
M4 Diameter Bolt M6 Diameter Bolt
3
M8 Diameter Bolt
M5 Diameter Bolt
Diagram 1A
M5 Diameter Bolt M8 Diameter Bolt
Diagram 1B
e
m
s
b
b
snf
og
t
c
c
tph
bc
i
m
s
s
q
b
s
s
q
nj
k
o
t
r
l
p
t
rc

Warning: Some TVs may require two people to lift! We are not responsible for personal injury or product damage.
Insert the Locking Bar(d) into the slots in the bottom of the Monitor Brackets so that is sits
behind the bottom tab on the Wall Plate. Once the Locking Bar passes out from the other side of wall plate, a padlock can
be added for additional security. Details see Diagram 3B.
First choose the desired vertical height you want, then hook the Monitor Brackets(b,c) over the top of the wall Plate(a) as
shown in the Diagram 3A.
4
Mounting the Wall Plate to the Wall
Step 2
Attaching Monitor to Wall Plate and Insert the Locking Bar
Step 3
Diagram 3A Diagram 3B
a
b,c
b
c
d
a
Brick, Solid Concrete and Concrete Block mounting:
Use the Wall Plate(a) as a template to mark 6 hole locations on the wall. Three in the top row of slots and three more in the
bottom row. Make sure these holes are level and there is at least 6" distance between any two holes. Pre-Drill these holes
with a 1/2" masonry bit to at least 2.5" in depth. Insert a Concrete Anchor(w) into each of these holes. Make sure the
anchor is seated completely flush with the concrete surface even if there is a layer of drywall or other material in front.
Attach the Wall Plate to the wall using 6pcs Lag Bolts(u) and 6pcs Lag Bolt Washers(v), shown in Diagram 2A.
Wood Stud mounting:
The Wall Plate(a) must be mounted to two wood studs at least 16" apart. Use a stud finder to locate two adjacent studs.
It is a good idea to verify where the studs are located with an awl or thin nail shown in Diagram 2B. Pre-drill a 2.5" deep
hole at the desired height in each stud using a 3/16" drill bit. Make sure these holes are in the center area of the studs and
level with each other. Use the Wall Plate as a template to mark the location of the second hole in each stud. Drill 2.5" deep
holes using the 3/16" drill bit in the marked locations. Attach the Wall Plate to the wall using the 4pcs Lag Bolts(u) and 4pcs
Lag Bolt Washers(v).
16 inch
16 inch
16 inch
Diagram 2BDiagram 2A
uv
a
Stud Finder
Thanks for choosing our products, enjoy the using.
wall