Allen + Roth 35158 User manual

1Lowes.com/allenandroth
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer service
department at 1-866-439-9800, 8 a.m. – 6 p.m., EST, Monday - Thursday, 8 a.m. – 5 p.m., EST, Friday.
ATTACH YOUR RECEIPT HERE
LED FAN
Français p. 18
Español p. 35
ITEM #0803776
MODEL #35158
welcoming • sophisticated • inspiring
allen + roth®is a registered trademark
of LF, LLC. All Rights Reserved.

PACKAGE CONTENTS
2
A
Hanging Bracket
Down Rod
Canopy
Blade
Motor Coupling Cover
Motor Assembly
B
C
D
E
F
1
1
1
5
1
1
PART DESCRIPTION QTY
Light Kit Housing
Light Kit
Canopy Hole Cover (preassembled)
Shade
Blade Iron
5-Watt LED tyoe B-10 Bulb
H
G
I
J
K
L
1
1
1
1
5
3
PART DESCRIPTION QTY
Lowes.com/allenandroth
A
F
C
H
E
B
G
J
I
K
D
I
L

HARDWARE CONTENTS
3
23A 12V
SAFETY INFORMATION
Hanging bracket Screw
Hanging bracket Washer
Wire Connector
Blade Screw
Wire Connector
HARDWARE BAG REMOTE CONTROL
Remote Control and Receiver
Remote Control Holder
Battery
Screws
Wood Screw
Lag Screw
Blade Iron Screws
Shade Screws
Flat Washer + Spring Washer
Please read and understand this entire manual before attempting to assemble, operate or install the
product. Save this manual when finished.
WARNING:
• Important: When using an existing outlet box, be sure the box is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury or
death.
• Turn off circuit breakers and wall switch to the fan supply wire leads. Warning: Failure to
disconnect power supply prior to installation may result in serious injury or death.
• Warning - Connecting this fan to a light switch (on/off) has been known to cause damage to the
receiver. This fan must be wired to continually receive power. Failure to do so will drastically
reduce the lifespan of this fan.
• Do not install fan on a ceiling with a pitch greater than 18°.
• WARNING – To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box
Marked 'Acceptable for Fan Support of 15.9 kg (35 lbs) or less' And Use Mounting Screws
Provided With The Outlet Box and/or Support Directly From Building Structure. Most Outlet Boxes
Commonly Used For The Support of Luminaires Are Not Acceptable For Fan Support And May
Need To Be Replaced. Consult A Qualified Electrician If In Doubt."
• Important: Be sure wiring box is properly grounded or that a ground (green) wire is present.
• Make sure the installation site you choose allows a minimum of 7 feet from the floor to the end of
the blades.
Lowes.com/allenandroth
Balance Kit

WARNING (continued)
CAUTION:
PREPARATION
4
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated assembly time: 30 minutes to 1 hour.
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,
electrical tape, ladder, safety glasses.
A B C
ASSEMBLY INSTRUCTIONS
• WARNING-To reduce risk of fire, electric shock, or personal injury, mount to outlet box marked
“Acceptable for Fan Support of 15.9kg (35lbs) or less” and use mounting screws provided with the
outlet box and/or support directly from building structure. Most outlet boxes commonly used for
the support of luminaries are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
• Warning-Risk of fire, electric shock, or personal injury. Ceiling fans may be either directly
supported from a structural framing member of a building and (see examples in figures A & B) or
may be mounted to an outlet box marked acceptable for fan support of 31.8 kg (70 lbs) to 15.9kg
(35 lbs) (see example in figure C).
• To reduce the risk of fire or electrical shock, do not use this fan with any solid state fan speed
device or variable speed control.
• Do not touch hot LED
• The LED light output is strong enough to injure human eyes. Precautions must be taken to
prevent looking directly at the LEDs with unaided eyes for more than a few seconds.
• Read and understand all instructions and illustrations completely before proceeding with assembly
and installation of this fixture.
• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate
completely, please contact a qualified licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts
out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate
the UL listing, C.S.A. certification, and/or ETL listing of this fixture.
• This fixture is intended for installation in accordance with the National Electric Code (NEC) and all
local code specifications.
• Use ONLY the supplied LED driver to power fixture.
• Driver cable is not intended for use through or concealed behind walls, floors, or ceilings.
Lowes.com/allenandroth

INITIAL INSTRUCTIONS
5
1.
Turn off the circuit breaker to the fan supply line
leads.
2. Secure the hanging bracket (A) to the ceiling outlet
box (not included) using hanging bracket screws and
hanging bracket washers.
Important: If attaching the fan to a sloped ceiling,
make sure the open end of the hanging bracket is
installed facing the floor. DO NOT install fan on a
ceiling with an angle greater than 18º.
DANGER: Failure to disconnect power supply prior
to installation may result in serious injury or death.
Lowes.com/allenandroth
1
1
2
2
A
1
20 20
OFF
OFF OFF
100
Hardware Used
x 2
x 2
Hanging Bracket
Screw
Hanging Bracket
Washer

DOWNROD ASSEMBLY INSTRUCTIONS
6Lowes.com/allenandroth
1. Loosen the set screws found on the coupling on top
of the motor assembly (F). Then, remove the
preassembled hair and clevis pin and save for later
use.
2. Insert downrod (B) through canopy (C) and motor
coupling cover (E).
1
F
Clevis Pin
Hair Pin
2a
2b
E
B
C

DOWNROD ASSEMBLY INSTRUCTIONS
7Lowes.com/allenandroth
3. Feed wires from the motor assembly (F) through the
downrod (B), then insert the downrod (B) into the
coupling found on top of the motor assembly (F).
3
B
F
4. Pass the previously removed clevis pin through the
downrod (B) and coupling of motor assembly (F),
then secure with previously removed hair pin.
Re-tighten set screws on the coupling.
5. Carefully lift the fan and seat the ball of the downrod
(B) in the hanger bracket (A). Be sure the groove in
the ball is lined up with the tab on the hanger bracket
(A).
4
B
F
5
A
B
DANGER: Be careful when aligning the tab to
the groove in ball. If not fully engaged, there is a
possibility of the fan falling, which may result in
serious injury or death.

SAFETY CABLE INSTRUCTIONS
8
1. For Canadian installation and for USA fans over 35
lbs, the safety cable must be installed into the house
structure beams using a 3” lag screw. Make sure
that when the safety cable is fully extended the lead
wires are longer than the cable and no stress is
placed on the lead wires.
Safety
Cable
Lag
Screw
Safety
Cable
Flat
Washer
Spring
Washer
1
Safety
Cable
Lowes.com/allenandroth
Hardware Used
x 1
x 1
x 1
Lag Screw
Flat Washer
Spring Washer

WIRING INSTRUCTIONS
9
1. Wiring the fan per wiring diagram and securely connect wires with wire connectors: Wrap electrical
tape (not included) around each wire connector and make sure no bare wire or wire strands are
visible after making connections.
• Connect WHITE wire from the fan to WHITE wire marked TO MOTOR N from the receiver.
• Connect BLUE wire from the fan to BLUE wire marked FOR LIGHT from the receiver.
• Connect BLACK wire from the fan to BLACK wire marked TO MOTOR L from the receiver.
• Connect BLACK wire from the outlet box to RED wire marked AC IN L from the receiver.
• Connect WHITE wire from the outlet box to WHITE wire marked AC IN N from the receiver.
• Connect GROUND (GREEN) wires from hanger bracket and downrod ball, to GROUND (GREEN
or BARE COPPER) from house.
Lowes.com/allenandroth
GREEN
GREEN
BARE
Receiver
BLUE
BLACK
WHITE
BLUE
BLACK
WHITE
1
WHITE BLACK
WHITE RED
Outlet Box
Hardware Used
x 6Wire Connector

WIRING INSTRUCTIONS
FINAL ASSEMBLY INSTRUCTIONS
10
• NOTE: The downrod (B) and canopy hole cover (I) are not used in the closemount option.
Lowes.com/allenandroth
2. Once wiring step has been completed, slide the
wired remote receiver in between the hanging
bracket (A) and the top of the downrod ball (B) with
the flat side of the receiver facing the ceiling. Turn
lead wires upward and carefully push them into the
outlet box, with the white and green wires to one
side of the box and the black wires toward the other
side.
1. Remove the 2 preassembled canopy screws on
hanging bracket (A) that align with the round holes
on the canopy (C) and loosen the other 2 canopy
screws (but do not remove them).
2. Raise canopy (C) over the hanging bracket (A),
twisting it until the loosened canopy screws engage
the keyslot of the canopy (C). Re-install the
previously removed canopy screws, then tighten all
screws securely.
2
A
C
1
A
C
2
A
B

FINAL ASSEMBLY INSTRUCTIONS
11 Lowes.com/allenandroth
3. Attach blade iron (K) to blade (D) with blade screws.
Do not fully tighten blade screws until each screw
has been started. Then, tighten each blade screw
starting with the center screw. Repeat for remaining
blade irons (K) and blades (D).
3
K
D
4. Attach blade irons (K) to the underside of the motor
assembly (F) with the blade iron screws.
5. Remove one of the preassembled mounting screw
from the motor assembly (F) and loosen but do not
remove the other two.
Blade Screw
K
F
4
Blade Iron
Screw
F
5
Hardware Used
x 15Blade Screw
Hardware Used
x 10Blade Iron Screw

FINAL ASSEMBLY INSTRUCTIONS
12 Lowes.com/allenandroth
6. Feed the wires from the motor assembly (F) through
the center hole in the light kit housing (G).
Position keyhole slots on light kit housing (G)
around the loosened mounting screws and twist
clockwise. Re-install the previously removed
mounting screw, then tighten all screws securely.
6
7. Remove one of the preassembled screws from the
light kit housing (G) and loosen but do not remove
the other two screws.
8. Connect wires from the motor assembly (F) to the
light kit (H) - WHITE to WHITE and BLACK to
BLACK.
Position keyhole slots on light kit (H) around the
loosened screws and twist it clockwise. Re-install the
previously removed screw, then tighten all screws
securely.
G
F
G
7
G
H
8

FINAL ASSEMBLY INSTRUCTIONS
13 Lowes.com/allenandroth
9. Insert bulbs (L) into sockets of light kit (H).
10.Raise shade (J) to the light kit housing (G) and
secure with shade screws.
J
G
10
Shade
Screw
CAUTION: An energy-saving wattage limiter
is included in the receiver. When replacing bulbs,
ensure bulb wattage is less than 190 watts,
otherwise the item will either dim the lights to 190
watts or will automatically turn off.
H
L
9
Hardware Used
x 3Shade Screw

FINAL ASSEMBLY INSTRUCTIONS
14 Lowes.com/allenandroth
Low
Speed
Fan
Off
Medium Speed
High
Speed
Light
On / Off
Fan control :
Low speed
Medium speed
High speed
To turn off the fan
Turns the light ON and OFF
as well as controlling the brightness setting.
OPERATION
11.There are 16 combinations of code for setting up the
remote control. If you do not use the dip switch set
up by manufacture then you will need to use the set
up procedures listed below.
Remove the remote control battery cover to expose
the remote dip switches. Use a small ballpoint pen
(not included) to set the dip switches to either up or
down.
a.) Install the 23A 12V battery (included) and replace the
battery cover you previously removed.
b.) After installing the unit and restoring power to the
fan, press and hold the “Light” button until the light
flashes (on/off) 3 times and will stay on, then the
control and speed setting process is complete. You
must press the “Light” button within 30 seconds of
restoring power to the fan.
c.) If programming is unsuccessful, retry the above
instructions.
The remote control comes with a cradle that may be
attached to the wall with the included screws.
REMOTE
CONTROL
11
RECEIVER
NOTE: Remove batteries if remote has
not been used for a long period of time
in order to avoid damage. Store remote
away from excessive heat or humidity.

15
Balancing Weight
Plastic Clip
5G
• Tighten screws on the mounting bracket, outlet box, the downrod , fan blades to blade holders,
and blade holders to the motor housing.
• Measure the distance from the tip of each blade to the ceiling. All blades should have the same
vertical distance from the ceiling. Adjust any bent blade holder, by gently pressing up or down on
the brackets, until all blades are at an equal distance from the ceiling.
If wobbling persists, you may need a blade balancing kit to stabilize the ceiling fan. A blade
balancing kit consists of a plastic clip and two balancing weights.
Determining the blade that needs to be balanced is a trial-and-error task.
1. Place a numbered piece of masking tape on each blade so you don't lose track of which blade is
which.
2. One blade at a time, attach the slotted plastic clip over the center of the blade edge and turn the
fan on. Observe which blade has the clip on when the ceiling fan wobbles the least.
3. Place the plastic clip on the edge of the blade, halfway between the blade holder and the blade
tip. Turn fan on and determine improvement.
4. If there is no improvement, turn off the fan again. Slide the clip along the length of the blade to
locate the source of instability.
5. Once you've found the faulty blade, press a balancing weight on the centerline. The weight
should be parallel to the clip.
STEPS TO BALANCING THE CEILING FAN
Lowes.com/allenandroth
Balance Kit

16
CARE AND MAINTENANCE
REVERSE
At least twice a each year tighten all screws and lower canopy to check mounting bracket screws
and downrod assembly. Clean fan housing with only a soft brush or lint free cloth to avoid
scratching the finish. Clean blades with a lint free cloth. Shut off main power supply before
beginning any maintenance. Do not use water or a damp cloth to clean the ceiling fan.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and
receiver, and connect the equipment into an outlet on a circiut different from that to which the fan is
connected.
Use the fan reversing switch to optimize your fan for seasonal performance.
Note: Wait for fan to stop before reversing the switch.
• In warmer weather, counterclockwise movement of the fan will result in downward airflow
creating a wind chill effect. Push switch to the left.
• In cooler weather, clockwise movement of the fan will result in upward airflow that can help move
stagnant hot air off the ceiling area. Push switch to the right.
Lowes.com/allenandroth

17
WARRANTY
Rev. 12-06-17
Lowes.com/allenandroth
Printed in China
The Distributor warrants that its products will be free from defects in material and workmanship for
one (1) year from the date of purchase by the Original Purchaser.
To replace a product that has a warranted defect, the Original Purchaser shall return any allegedly
defective parts or products to the authorized Distributor the product was purchased from with PROOF
OF PURCHASE, Original Purchaser’s name and return address and a description of the claimed
product defect.
If any of the warranted products are found by Distributor, in its sole discretion, to be defective, such
products will, at Distributor’s sole option and cost, be replaced, repaired or refunded less an amount
directly attributable to Original Purchaser’s prior use of the product. Distributor will return the repaired
or replaced product prepaid freight. This warranty does not cover labor or other costs or expenses to
remove or install any defective, repaired or replaced product.
The parties hereto expressly agree that Original Purchaser’s sole and exclusive remedy against
Distributor shall be for the repair, replacement or refund of defective products as provided herein.
This warranty extends only to product ownership by the Original Purchaser; is not transferable
whether to heirs, subsequent owners, or otherwise; and is void if the Original Purchaser ceases to
own the product.
This warranty does not apply to any products that have been subjected to misuse, mishandling,
misapplication, connected to voltage at more than 5% above standard North American voltage,
unusual use (including but not limited to use in an environment where the annual average ambient
operating temperature is below 27ºF or above 95ºF), neglect (including but not limited to improper
maintenance), accident, acts of god such as high winds, improper installation or care, failure to follow
the Product’s written instructions for normal use and care, improper packaging of products returned to
the Distributor, modification (including but not limited to use of unauthorized parts or attachments), or
adjustment or repair. Significant product exposure to chemicals, harsh cleaners, salt water or salt air
will void any and all warranties on exterior finishes. This warranty only applies when all components,
including transformers, have been provided by the Distributor. Substituting another manufacturer’s
product and/or components will render the warranty completely void.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS
MAY NOT APPLY TO YOU.
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR
PURPOSE OR INFRINGEMENT. ORIGINAL PURCHASER SHALL IN NO EVENT BE ENTITLED
TO, AND THE DISTRIBUTOR SHALL NOT BE LIABLE FOR, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE, INCLUDING, BUT NOT LIMITED TO LOSS OF
PROFIT, PROMOTIONAL AND/OR MANUFACTURING EXPENSES, OVERHEAD, INJURY TO
REPUTATION AND/OR LOSS OF CUSTOMERS.

18 Lowes.com/allenandroth
VENTILATEUR DE PLAFOND À DEL
ARTICLE #0803776
MODÈLE #35158
welcoming • sophisticated • inspiring
allen + roth est une marque de commerce déposée
de LF, LLC. Tous droits réservés.
Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant,
appelez notre service à la clientèle au 1-866-439-9800, entre 8 h et 18 h (HNE), du lundi au jeudi, ou
entre 8 h et 17 h (HNE) le vendredi.
JOIGNEZ VOTRE REÇU ICI
Numéro de série Date d’achat

19 Lowes.com/allenandroth
CONTENU DE L’EMBALLAGE
A
Support de suspension
Tige
Pavillon
Pale
Cache raccord du moteur
Ensemble moteu
B
C
D
E
F
1
1
1
5
1
1
PIÈCE DESCRIPTION QT É
Logement du kit d'éclairage
Kit d'éclairage
Canopy Hole Cover (preassembled)
Abat-jour
Support des pales
Ampoule à DEL de 5 watts type B-10
H
I
J
K
L
1
1
1
1
5
3
PIÈCE DESCRIPTION QT É
G
A
F
C
H
E
B
G
J
I
K
D
I
L

QUINCAILLERIE INCLUSE
20
Vis du support de suspension
Rondelle du support de suspension
Capuchon de connexion
Vis de pale
Capuchon de connexion
SACHET DE QUINCAILLERIE TÉLÉCOMMANDE
Télécommande et Récepteur
Support de la télécommande
Pile
Vis
Vis à bois
Tire-fond
Vis du support des pales
Vis de abat-jour
Rondelle plate + rondelle ressort
Lowes.com/allenandroth
Ensemble d'équilibrage
CONSIGNES DE SÉCURITÉ
Veuillez lire et assurez-vous d'avoir compris l’intégralité du présent guide avant d’assembler, d’utiliser ou d’installer ce
produit. Conservez ce manuel lorsque vous avez terminé.
.
AVERTISSEMENT :
• Important : Lorsque vous utilisez une boîte de sortie existante, assurez-vous que la boîte est fermement attachée à la
structure du bâtiment et peut supporter le poids total du ventilateur. Le non-respect de cette recommandation peut
entraîner des blessures graves ou la mort.
• Coupez les disjoncteurs et l'interrupteur mural qui contrôlent les fils d'alimentation du ventilateur. Avertissement : Si
l'alimentation électrique n'est pas coupée avant l'installation, il peut en résulter de graves blessures ou la mort.
• Avertissement – Connecter ce ventilateur à un interrupteur pour lampe (marche/arrêt) endommage le récepteur. Ce
ventilateur doit être câblé afin de recevoir du courant en continu. Le non-respect de cette recommandation réduira
considérablement la durée de vie de ce ventilateur.
• Ne pas installer sur un plafond incliné à plus de 18°.
• AVERTISSEMENT – Pour réduire le risque d'incendie, de choc électrique ou de blessures corporelles, installez le
ventilateur sur une boîte de sortie marquée "Convient pour supporter un ventilateur de 15,9 kg (35 lb) maximum" et
utilisez les vis de montage fournies avec la boîte de sortie et/ou fixez directement sur la structure du bâtiment. La
plupart des boîtes de sortie utilisées couramment comme support de luminaires ne conviennent pas au support d'un
ventilateur et devront être remplacées. Consultez un électricien qualifié de cas de doute.
• IMPORTANT : Assurez-vous que le boîtier de connexion est correctement mis à la terre ou qu'un fil de terre (vert) est
présent.
• Assurez-vous que le site d'installation choisi offre une hauteur minimum de 2,13 m (7 pi) entre le sol et le dessous
des pales.
23A 12V