AllMounts AS0246BTW User manual

AS02R
AS02
ISSUED: MAR. 2014
Flat Panel Mobile Cart/Floor Stand and Accessories
INSTALLATION MANUAL
CAUTION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
300x300/400x200
400x400/600x400
AS0246BTF
70"
MAX
60kgx2
(132lbsx2)
RATED
60kgx2
(132lbsx2)
RATED
AS02H
AS0246BTW
70"
MAX
300x300/400x200
400x400/600x400
10kg
(22lbs)
RATED
10kg
(22lbs)
RATED
All accessories
14. Adjustment
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
+3° -3°
+5°
-10°
Optional Accessories
Note: The accessories are not standard.
The accessories will be selected according to user
requirement.
AS03V
AS01K

Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
AS0246BTW/BTF
WARNING
21
NOTE: Read the entire instruction manual before you start installation and assembly.
Package M (x2)
washer
M-F
(x4)
M8x20
M-C
(x4)
M5x14
M-A
(x4) M6x14
M-B
(x4)
big spacer (x4)
M-H
M6x30
M-D
(x4)
M8x30
M-E
(x4) small spacer (x8)
M-G
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
connecting piece (x1)
K
top cover (x1)
N
left (x2)
I
adapter bracket
3mm Allen key (x1)
S
M8x40(X4)
R
right (x2)
J
adapter bracket
column (x1)
M
5mm Allen key (x1)
T
6mm Allen key (x1)
U
M8x16 (X4)
Q
M8x65 (x8)
P
cable clamp (x8)
O
D8 steel washer
G
(x8) D8 plastic washer
H
(x8)
M8
L
(x4)
left cover
C
(x1) right cover(x1)
D
base
B
(x2)middle base (x1)
A
Component (AS0246BTW only)
supporting foot (x4)
Y
caster wheel/brake
V
(x2) caster wheel
W
(x2) wrench (x1)
X
Component ( onlyAS0246BTF )
rubber pad (x4)
Z
(Peel off the backing paper from the rubber pad
and stick the rubber pad on to the supporting foot.)
universal plate 2 (x1)
F
universal plate 1 (x1)
E

Attach the left and right base to the middle base using the appropriate screws. Tighten all screws with an
Allen key.
4
3
1. Assembling the Base
K
2. For the model AS01K installation
(Assembly based on the accessories selected by user.)
3. Attaching the Column to the Base
Attach the power socket to the back of column using the appropriate screws. Tighten all screws with a
phillips screwdriver.
Attach the column to the assembled base using the connecting piece, secure them with the appropriate screws.
NOTE: Lock the brakes on the casters to avoid any sudden movements during installation.
PU
T-H
R
U
G
AS02H
AS02
AS03V/AS02P
AS02R
host machine
rack (x1)
T-A
Package P
laptop box (x1)
T-D
support rod (x2)
T-F
camera shelf (x1)
T-G
connecting piece (x1)
T-B
silicone pad (x8)
P-C
iron shelf (x1)
T-C
Package P
key (x1)
P-F
M6x8 (x4)
P-D
AS01K
power socket (x1)
T-H
M6x8 (x4)
P-A
4mm Allen key (x1)
P-B
AS03V only
D6 washer (x4)
P-E
connecting piece (x1)
T-E
ST4.8x9.5 (x4)
P-G
The following accessories are optional.
P-G
Note: With the brake
wheels facing forward.
A
B
B

6
5
4. Installing the Covers
C
D
5. For the model AS02H installation
(Assembly based on the accessories selected by user.)
P-A
5-1: Installing the host machine rack on the back of the column
Insert the host machine rack to the desired position along the column rails. Tighten all screws to secure
it with an Allen key.
Peel off the backing paper
from the silicone pads and
stick the silicone pads on
to the host machine rack.
Attach the connecting piece to the host machine rack using the appropriate screws. Tighten all screws
with an Allen key.
NOTE: With the arrow pointing upward.
T
P-B
P-C
T-B
T-A
T
5-2: Installing the host machine rack on the side of the column
(If the power socket is installed on the back of the column)
Loosen the screws in order to separate the metal plate from the connecting piece.
Attach the previously removed plates to the host machine rack using the previously removed screws.
Tighten all screws with an Allen key.
Insert the host machine rack to the desired position along the column rails. Tighten all screws to secure
it with an Allen key.
T
T
metal plate
metal plate

8
7
Insert the laptop box to the desired position along
the column rails, Tighten all screws to secure it with
an Allen key.
P-F
T
Use the key to open the laptop box.
Put the DVD into the box gently , then close the box and lock it.
DVD
6. For the model AS02 installation
(Assembly based on the accessories selected by user.)
Insert the iron shelf to the desired position along the column rails. Secure it by tightening screws with an
Allen key.
• n
• Put the host machine in the rack and push gently on one side of the rack to keep it close to the host
machine, then tighten the knobs to secure.
• Use the adjustable buckles to hold the machine firmly in place.
Loosen the k obs to pull one side of the rack to make it keep the maximum space.
knob
buckle
7. For the model AS03V installation
(Assembly based on the accessories selected by user.)
NOTE: With the arrow
pointing upward.
P-D
P-E
Attach the connecting piece to the laptop box
using the appropriate screws and washers.
Tighten all screws to secure it with a proper
phillips screwdriver.
T-E
T-D
T-C
T

10
9
10. Installing the Universal Plate
Insert the universal plate to the desired position along the column rails.
Tighten all screws to secure it with an Allen key.
NOTE: With the arrow pointing upward.
11. Installing the Top Cover
Attach the top cover to the column using the
appropriate screws. Tighten all screws with an
Allen key.
T
8. Assembling the Universal Plates
O
U
Q
N
12. For the model AS02R installation
(Assembly based on the accessories selected by user.)
Remove two plastic caps for the camera shelf installation.
Tighten the support rods to the camera shelf.
T-G
T-F
Attach the universal plate 1 to the universal plate 2 using
the appropriate screws, washers and nuts.
9. Installing the Cable Clamps
H
G
LH

13-1 For Flat Back Screens
TV
TV
TV
12
11
13. Installing the Adapter Brackets
Top of the display
M-A/M-B/M-C
M-F
Insert the support rods to the desired position (Determine the position for support mount keeping in mind
display size.) along the column slots and tighten both screws to secure the support mount.
13-2 For Recessed Back Screens or to Access A/V Inputs
TV
TV
TV
M-D/M-E
M-F
M-H
M-G
M-D/M-E
M-F
M-H
M-C M-D/M-E/
M-F
M-G
M-C
M-F
M-G
or or or
Tighten all screws but do not over tighten.
· Position the adapter brackets as close as possible to the center of the displays.
· Screw the adapter brackets onto the displays.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screens.
S

14. Hanging the Displays onto the Universal Plates
14
13
• Lift the display carefully and pull downward two straps at the same time , then hook the adapter brackets
to the universal plate. Fasten the adapter brackets to the universal plate by releasing the straps.
• The other display is hung onto the universal plate in the same way.
• Use the padlocks to prevent the displays from being stolen (The padlocks are not included).
13. Cable Management
Run the cables through the cable clamps and the rubber strip.