ALPHA PLAM ALFA 90 PELET User manual

USER MANUAL
ALFA 90 PELET
Ecological burning stove that heats your home
ALFA PLAM

2
Heating appliances (hereinafter referred to as "stove") of ALPHA PLAM are constructed and their
technical acceptance test was performed on the basis of safety regulations stated in the referent
European Union directives.
This manual is intended for owners, installers, workers and staff responsible for stoves
maintenance.
In case of any doubt, and for all clarifications, please contact the manufacturer or authorized
service, and specify the number of the disputed paragraph.
Printing, translation and reproduction, even partial, of this Manual must be authorized by ALFA
PLAM Company.
Technical information, graphics and specifications in this Manual may not be published.
DOUBLE COMBUSTION SYSTEM
Flame produced by wood that is properly burning in
a stove emits the same amount of carbon dioxide
(CO2) that is released due to the natural
decomposition of the wood itself.
The amount of CO2 produced as a result of
combustion or decomposition of a plant, is equal to
the amount of CO2 that the plant itself can take from
the air and convert into oxygen, which is released
into the air and into the carbon it consumes during
its life cycle.
Using non-renewable fossil fuels (coal, oil, gas),
unlike to what happens with the wood, releases into
the air large amounts of CO2, accumulated over
millions of years, increasing the greenhouse effect.
However, the use of wood as fuel is in perfect
balance with nature since it uses renewable fuels,
which is in conformity with the environmental cycles
of nature.
The principle of clean combustion is fully compliant
with the objectives and the firm ALFA PLAM took
care about it when designing its products.
What do we mean by clean combustion and how do we achieve this? Control and regulation of
primary air and secondary air insertion leads to the second combustion, that is to post combustion
characterized by a second, stronger and lighter flame that develops above the main one.
That flame, thanks to the introduction of a new oxygen combusts gases significantly by improving
performance and reducing heat to a minimum emission of harmful CO (carbon monoxide)
generated due to incomplete combustion. This is an exclusive feature of the stoves and other
products of the company ALFA PLAM.

3
TABLE OF CONTENTS
1
INTRODUCTION
7.
PUTING INTO OPERATION AND
USING OF THE STOVE
1.1 SYMBOLS 7.1 PELLET LOADING
1.2 PURPOSE 7.2 CONTROL PANEL DESCRIPTION
1.3 PURPOSE AND CONTENTS OF THE
MANUAL
7.3 START UP PHASE
1.4 STORING MANUAL 7.3.1 Electric Power
1.5 UPDATING OFTHE MANUAL 7.3.2 Phase of work
(ignition)
1.6 GENERAL INFORMATION
1.7 GENERAL PROVISIONS RELATING
TO PREVENTION OF ACCIDENTS
AT WORK AND THOSE THAT HAV E
TO BE OBSERVED
7.4 WORK PHASES
1.8 STATUTORY WARRANTIES 7.5 SWITCHING OFF PHASES
1.9 MANUFACTURER’S
ACCOUNTABILITY 7.6 ADVANCED USE OF THE CONTROL PANEL
1.10 CHARACTERISTICS OF THE USER 7.6.1 Clock
1.11 TECHNICAL ASSISTANCE 7.6.2 Timer
1.12 SPARE PARTS 7.7 ALARMS
1.13 IDENTIFICATION TABLE 7.7.1 Alarm Alar ACC (ignition alarm)
1.14 STOVE DELIVERY 7.7.2 Cool Fire Alarm
(Alarm to stop AC power)
7.7.3 Alarm Alar Sond
(Alarm probe to smoke)
2
SAFETY RULES 7.7.4 Alarm Alar DEP
(Alarm for depression)
2.1 WARNINGS FOR INSTALLING 7.7.5 Alarm Alar PELL
(Alarm for pellet temperature)
2.2 WARNINGS FOR USERS 7.7.6 Alarm Alar Fan
(Alarm for the air induction fan)
2.3 WARNINGS FOR MAINTENANCE
WORKERS 7.7.7 Alarm Alar hot (alarm for the high smoke temperature)
7.7.8 Alarm Fire Alar
(Alarm for fire extinction during the
phase of work )
3
SPECIFICATIONS AND
DESCRIPTION OF FUEL AND
STOVE
7.7.9 Alarm Alar Sic
(Alarm for the main thermostat)
3.1
CHARACTERISTICS OFFUEL
3.2 STORAGE OF PELLET
8
MAINTENANCE AND CLEANING
3.3 DESCRIPTION OF THE MAIN
PARTS OF THE CABINET 8.1 SAFETY MEASURES

4
8.2 REGULAR MAINTENANCE BY THE
USERS
4
DELIVERY AND TRANSPORT 8.2.1 Interior cleaning of furnace
8.2.2 Cleaning ashtray
5
PREPARING SPACE FOR
INSTALLATION
8.2.3 Glass cleaning
5.1 PRECAUTION MEASURES 8.2.4 Chimney Cleaning
5.2 GENERAL MEASURES 8.2.5 Setting of the lever
5.3 PLACE FOR INSTALLING THE
STOVE
5.4 AIR USED FOR COMBUSTION
9
INFORMATION ON THE
DESTRUCTION AND TRANSPORT TO
LANDFILL
5.5 SMOKE DISCHARGE
5.5.1
Pushing the smoke up the chimney
onto the roof
10
ELECTRIC SCHEME
6
INSTALLATION
TECHNICAL SPECIFICATIONS
6.1 LEVELLING THE STOVE
6.2 CONNECTING THE APPLIANCE
6.2.1
Connecting to the power
supply
6.2.1.2
Commissioning
Dear Customer,
First of all, we wish to thank you for the trust you have placed in us by purchasing our
product and we congratulate you on your choice.
To make sure that you use your new stove in the best way, we advise you to read this
manual carefully.
1
INTRODUCTION
Do not do anything if you have not understood all the information outlined in the
manual; in case of any doubt, seek assistance from specialized staff of ALFA PLAM
company.
ALFA PLAM reserves the right to change at any time the specifications and technical
and / or functional characteristics of the stove, without prior notice.
1.1
SIMBOL
S
In this manual, very important items are highlighted with the following symbols:
.
DANGER: This symbol expresses a significant remark about the behavior in order to
prevent accidents or damage to materials

INSTRUCTION
: Instruction regarding the proper use of the stoves and the
responsibility of the authorized persons
!
ATTENTION:
An item that is of great importance.
!
DANGER:
This symbol expresses a significant remark about the behavior in order to
prevent accidents or damage to materials

5
1.2
PURPOSE
! The ALFA PLAM unit is a new stove for heating, with its advanced technology, which
only uses pellets and and thanks to automatic operation creates a healthy and safe
heat in space.
The Stove shall work exclusively with a sealed combustion chamber door.
Do not open the door when the stove is operating.
The stove is characterized by a double combustion system: PRIMARY and
SECONDARY with positive effects in terms of performance and in terms of discharge of
the "cleaner smoke."
The above purpose and the designed configuration of the stoves are the only ones
allowed. Manufacturer: never use the stove in non compliance with the submitted
guidelines.
! The above stated purpose is valid only for the devices with the complete structural,
mechanical and installation efficiency. ALFA PLAM stove is a device for indoor space
only.
1.4
STORING
MANUAL
STORING AND CONSULTATION
The manual must be carefully stored and must always be available for consultation, both
from the users, as well as by the staff responsible for installation and maintenance.
Manual - Instructions for use and maintenance is an integral part of the stove.
DESTRUCTION OR LOSING
If necessary, ask the company ALFA PLAM for another copy.
ASSIGNMENT OF THE STOVES
In case of an assignment of the stove, the user is required to submit a new customer with
this manual.
1.6
GENERAL INFORMATION
INFORMATION
In case of exchange of information with the manufacturer of the stoves, it is necessary to
specify the serial number and identification data listed on the page "GENERAL
INFORMATION" at the end of this manual.
RESPONSIBILITY
By submitting this manual, ALFA PLAM company is exempted from any responsibility,
both civil and criminal, in case accidents caused by partial or total disregard of
specifications listed therein.

In addition, ALFA PLAM company is exempted from any repsonsibility in case of
nondesignated or improper use of stove by the user; in case of unauthorized
modifications and / or repairs, in case of use of non-original spare parts or those that are
not designed for this model of the stove.
EMERGENCY MAINTENANCE
Extraordinary maintenance must be performed by qualified personnel trained to intervene
on the model stoves referred to in this manual.
.
ACCOUNATBILY FOR ACTIONS DURING INSTALLATION
Responsibility for actions taken when installing the stove cannot be assignesd to ALFA
PLAM, company but responsibility goes, and remains, with an installer, who is required to

6
conduct checks as for the chimney and bringing of air, as for properly proposed
installation solutions. In addition to that, all safety regulations and applicable special
legislation of the state in which the stove is being installed have to be complied with.
USE
Except for the regulations listed in this manual, using the stove is to be in line with all
applicable safety regulations provided for by special legislation of the state in which the
stove is installed.
1.8
LEGAL GUARANTEE
To be able to use the legal guarantee in accordance with EEC Directive 1994/44/CE, the
user has to strictly abide by the guidelines contained in the manual hereof, the user is to,
in particular:
- use the stove within the stipulted limits;
- regularly and carefully maintain the stove;
- for the use of the stove, authorize persons of proven ability, behavior and those
adequately trained for this purpose.
Failing to comply with the information given in this manual shall lead to the loss of
warranty.
1.9
MANUFACTURER’S RESPONSIBILITY
!
MANUFACTURER’S RESPONSIBILITY
Manufacturer is exempted of any civil and criminal accountability, direct or indirect, in the
case of:
- Installation which is not in accordance with the applicable regulations in the State
with the safety recommendations;
- Not following the instructions contained in the manual;
- Installation which is performed by unqualified and unskilled staff;
- Usage which is not in accordance with safety recommendations contained in this
manual;
-
Performed modifications and repairs for which the user has not obtained the
authorization from the Manufacturer;
-
Using of spare parts or those that are not specific to this model of stove;
-
Non-maintenance of the stove;
-
Extraordinary events
.
1.10
REQUIRED CAPABILITIES OF THE
USER
User of the stove is an adult, a responsible person with the technical knowledge
necessary for routine maintaining of mechanical and electrical parts of the stove.
Make sure that children do not approach the stove that is turned on, in order to play.
11.1
TECHNICAL ASSISTANCE
ALFA PLAM company is able to solve any technical problem related to usage and

7
maintenance of the stove, throughout its lifetime.
Central office is at your disposal so as to refer you to your nearest qualified service
facility.
1.12
SPARE PARTS
Use only original spare parts.
Do not wait for the parts to wear out from use before replacing them.
Replacement of the seedily parts before the breaking leads to prevention of accidents
that occur because of sudden breakage of parts, which can harm people and cause
damage to property.

Carry out periodical inspections on maintenance as specified in the "MAINTENANCE
AND CLEANING“chapter
1.13
NAME
PLATE
The main nameplate affixed to the stove contains all the characteristics of the product,
including information on the manufacturer, identification number and CE mark.
1.14
DELIVERY OF THE STOVE
The stove is delivered in perfect packaging in a cardboard box. Attached to the wooden
base which enables its movement with the help of forklifts and/or other means.
Inside the stove there is following material:
- Manual for usage, installation and maintenance;
- Spatula for cleaning the stove (channel through which the smoke flows).
2
SAFETY WARNINGS
2.1
WARNINGS FOR INS
A
TLLER
!
- Make sure the specifications for the reception of the stove are in accordance with
the local, national and European regulations.
- Adhere to the guidelines from this manual.
- Make sure the specifications of the of chimney and equipment for taking air are in
accordance with the required type of installation
- Do not carry out bare electrical connections with temporary and non-insulated
cables
- Check whehether the grounding of electrical devices is efficient.
- Always use the means for personal protection and other protective equipment as
provided by law
2.2
WARNINGS FOR USER
! -
Prepare the space needed to install the stove in accordance with the local, national
and European regulations.
-
Because it is a heating device, the stove has very hot outer surfaces.
It is therefore recommended to use extreme caution during work, and in particular :
-
Do not touch and or approach the glass door which may cause burns;
-
Do not touch the pipe through which the smoke flows;
-
Do not perform any cleaning;
-
Do not open the door with glass;

8
-
Make sure that the children do not approach the stove;
-
- Adhere to the guidelines contained in this manual.
-
Keep to the guidelines and warnings from the plates affixed to the stove .
-
On the plates, there are guidelines for preventing accidents at work, so they must
always be fully readable. If they are damaged or become illegible, they must be
replaced, requests the Manufacturer to provide an original replacement.
- Use only the fuel in line with the guidelines from the chapter relating to the the fuel
characteristics.
-
Strictly adhere to the plan for regular and emergency maintenance.
-
Do not use the stove without daily control performed as specified in the
"Maintenance" chapter of this manual.
-
Do not use the stove in case of malfunction, in case of doubt that something is
broken or in case of unusual sounds
-
Do not throw water on the stove in operation, or for the purpose of extinguishing the
flame in ember tray.
-
Do not extinguish stove by disconnecting the plug from the socket.
-
Do not lean over an open stove, it can endanger its
stability.
- Do not use the stove as support or for of any kind of
anchoring
- Do not clean the stove before completing cooling
down of its structure and ashes.
- Touch the door only when the stove is cold
- Conduct all the operations calmly and in the
conditions of maximum safety.
- In the case of fire in the chimney, turn off the stove in
the manner described for extinguishing described in
the chapter 7.
ATTENTION: In order to avoid any danger
caused by accidental plug in thermal switch,
this stove should not be supplied through a
device with exterior control, such as timer,
but it should be connected to the circuit that
is regularly supplied and disconnected from
the network.
.
- In case of the poor operation of the stove caused by a
week draft of the chimney, the same should be
cleaned by applying the procedure described in 8.2.5.
In any case, the cleaning of the chimneys should be
conducted at least twice a year, in accordance with
the guidelines from the article 8.2.5.
- Do not touch the painted parts during the stove
operation of, so that the damaging of the colour can
be avoided.
- Replacement of the fuse is done by qualified
personnel.
2.3
WARNINGS FOR MAINTAINANCE WORKER
!
- Abide to the guidelines from this manual.
- Always use means for personal protection and other
protective devices.
- Before beginning with any sort of maintenance, make
sure that the stove, in case it has already been used,
has cooled down.
- In case that any safety device is not working, it is
considered that the stove is not working.
- Pull out the plug in from the socket on the wall before

9
work on electrical, electronic parts and connectors.
3
CHARACTERISTICS O
F FUEL AND STOVE DESCRIP
TION
3.1
FUEL CHARACTERISTICS
- Pellets or wooden rollers (Figure 3.1) is a mixture of different kinds of wood
compressed by mechanical procedures observing environment protection
regulations
It is the only kind of fuel prescribed for this kind of stove.
- Efficiency and thermal power of the stove can vary in accordance with the kind
and quality of the used wooden rollers.
In order for the stove to work correctly, it demands rollers with the following
characteristics:
- dimensions Ø 6 – 7 mm
- maximum length 30 mm
- maximum content of the humidity 8% do 9%
- The stove is equipped with the storage for wooden rollers with the capacity
depicted in the above stated column of characteristic data.
The door for loading are placed on the upper side.
 -
The cover can always be opened so that loading with the wood rollers
can
be conducted.
!
For
resetting of the control at
the working temperature it is not possible to use the
classical fuel.
!
It is forbidden to use the stove for incineration.
Fig.3.1
3.2
PELLET STORAGE
! Pellets should be kept in a dry, not too cold space.
It is recommended that a couple of sacks with pellets should be kept in a room in which
the stove is used or in a adjacent room because of the acceptable temperature and air

10
humidity.
Moist or/and cold pellets (5
o
C) reduce the thermal power of fuel and require more
detailed cleaning of the ember tray (of non-burned material) and combustion chamber.
! Special attention should be paid to storage and moving of the sacks with pellets. One
should avoid its breaking and making of splinters.
If splinters are put in the storage of the stove, it could cause blockage of the system of
pellet loading.
3.3.
DESCRIBTION OF
MAIN PARTS OF THE STOVE
A)
Pellet storage
B)
Door with a handle
C)
Combustion c
hamber
D)
Ashtray
drawer
E)
Control panel
F)
Ember tray
G)
Fan for heating up the space
It is placed in the lower part of the stove. It is automatically moved when the
body of the stove is heated and is automatically extinguished when it is cooled
down.
H)
Smoke expulsion
f
an
It enables aggressive smoke expulsion and simultaneous intake of the air
which is combusted in the ember tray. It works parallel with the system for
loading and exchanges the power for smoke discharge in dependence of the
thermal power.
I)
Thermostat for manual pellet loading
L)
Pressure switch (pressostat)
M)
Thermostat for manual boiler loading
N)
Loading System
It consists of the regulator and dispenser and enables pellet to fall in the
ember tray.
O)
Ele
ctronic small board
P)
S
tove ignition
s
witch
Q)
Electronic lighter
Fig. 3.3.1

11
Fig.3.3.2
Fig. 3.3.3
4
DELIVERY AND TRANSPORT
The stove is delivered with all the associated parts.
Be careful – the stove has a tendency to turnover.
!
Centre of gravity of the stove is moved to the left.
Take care of the above stated even in case of the moving of the stove.
During lifting avoid difficult moves.
Make sure that the fork lift truck has a bigger carrying capacity than the weight of the
stove it should lift.
The operator of the fork lift truck shall be the only person responsible for the lifting of
the weight.
!
Make sure
the children do not play with parts of the packaging material (e.g:
cellophane and polystirol)
Danger of suffocation!
5
PR
EPARING
THE SPACE FOR INSTALLATION
5.1
PRECAUTION MEASURES
!
It is the user who shall bear and keep the responsibility for the operations
conducted in the space in which the stove shall be installed and he/she is

12
entrusted to carry out the checks in regard to the proposed installation
The user is to comply with all the local, national and European safety regulations.
Stove must be installed on the floor of the appropriate capacity.
Instructions for assembly and disassembly of the stove are only intended for
specialized technicians.
Advice to users is to always address our technical assistance with the request for
qualified technicians.
In case of recruitment of other technicians, it is recommended that you check their
actual abilities.
Before beginning with the phase of assembling or disassembling of the stove, the
installer, has to apply security measures provided by law, in particular he is :
A) not to operate in the conditions hampering him in his work;
B) to work in perfect mental and physical conditions and make sure that the
means for the personal protection are complete and in good condition;
C) to wear protective gloves;
D) to wear protective shoes ;
E) to use tools with insulation against electric shock;
F) to make sure that the space in which assembly or disassembly is performed is
freed from obstacles.
5.2
GENERAL MEASURES
There are many factors that influence the effectiveness of fire - in terms of thermal
performance and low emission of pollutants (CO - carbon monoxide).
Some factors depend on the stove, but some depend on the characteristics of the
space, installing and the extent of regular maintenance of products.
Some of the important factors are:
- air that is used for combustion;
- Characteristics of the drainage system for the products of combustion;
- The quality of pellets (moisture content and dimensions).
The following paragraphs lay down certain guidelines that should be followed in order
to achieve the best performance of the purchased products.
5.3
PLACE OF
INSTALLING THE STOVE
Picture (Fig. 5.3.1) shows a minimum distance that must be allowed for when setting up
the stove in the regard of the materials and flammable objects.
A)
Adjoining wall
B)
The wall behind the stove
C)
The side wall
D)
Protection of the floor
Protect from the flame heat radiation all the things that could ignite if exposed to
excessive heat.
Wood floors or those made of combustible materials must be protected with non-
combustible material, such as sheet metal of 2-3 mm thickness
Protection must cover the entire floor area in front of the stove.
The stove can be installed between two walls. .
Minimum space that should be allowed between the stove and the wall surfaces should
be 2 cm.
Any wooden beam placed over the stove must be protected by refractory material.

13
! If the above stated conditions are not fulfilled, the stove cannot be installed.
Fig.5.3.1
Fig.5.4.1
Fig.5.4.2
5.4
AIR
USED FOR COMBUSTIO
N
! The
stove, during its operation takes the air from the room in which it is located through
the hole located on the rear right side of the stove.
The place for taking air from outside can be linked with a hole in the wall by means of
the pipe with a gasket, whose diameter is 80 mm.
!
The maximum
length of
the air intake
pipe
is
4.5
m
with
a maximum of 3
cranks
with an angle of 90
o
. .

14
Air inlets should be placed at a height of 20-30 from the soil.
From the outside, a grid must be placed for permanent ventilation, in very windy areas
exposed to rain and wind, protection must be provided from rain and wind.
If it is impossible to provide the room with outdoor air, it is possible to make an external
opening in the adjoining room, but constant communication with the transit grid must be
provided. The stove configured in this way is no longer hermetically sealed in regard to
the room in which it is installed (Fig. 5.4.2 - C = Crate, G = grid, S = shade).
!
It is forbidden to
take
the air
out of the garage
, storage
with
flammable
materials
or areas where there is a risk of fire.
!
If there are
several other
heaters
in
the area
and the
stove
is
not
hermetically
sealed in the space where it is installed, the access to the air supply must be
guaranteed for the amount of air necessary for the operation of all appliances.
!
If
in
the
area
where
the
stove
is set
,
one
or more
fans for air expulsion
(
aspirator)
is working , it is necessary to check that there are is no poor performance of the
stove caused by the insufficiency of air needed for combustion
Fig.5.5.1
5.5
SMOKE EXPULSION
!
The stove works with combustion chamber in depression and therefore it is
absolutely necessary to check if the smoke discharge channel is hermetically
closed.
-
After choosing the appropriate place for installing and after having in mind
the above stated measures in paragraph 5.3, the place for the smoke
discharge pipes should be determined.
-
The pipes which should be used must be stiff, made of aluminium tin (at
least 1,5 mm thick) or made of stainless steel (at least 0,5 mm thick) with
nominal diameter of 8 cm and with the gaskets (up to 5 meters long) or
up to 10 cm with gaskets (over 5 meters long ) (Figure 5.5.1)
It is advised that the pipes should be isolated with isolation material (glass
A – Chimney cap
B – Checking
C – Acclivity
H – Height

15
wool of minimal thickness of 2 cm) or steel pipes with double layer should
be used, whereas, possibly, the vertical part, if internal, does not have to
be double-layered.
! -
It is mandatory that the first vertical part should be at least 1,5 meter long
so as to guarantee regular smoke discharge.
It is desirable to make up to 5 to 6 changes of directions of the crank up to 45-90
o
or T
joints.
- Always use T joints with access eyes at each horizontal and vertical
change pipe direction.
- Horizontal parts must not be longer than 2-3 m with acclivity of 3-5%.
- Anchor the pipes to the walls.
!
Pipe joint MUST NOT BE CONNECTED
-
On the chimney used by other smoke gen
erators (stoves, fire
-
places, etc.)
-
On the system for air extraction (aspirators, valves, etc.) even if
connected to tubes.
!
It is forbidden to install the
valves
to turn off the
draft
.
!
For
the pipe length of over
5
meters or
in low
draft c
onditions
(
the presence
of many
curves, inadequate endings of discharge channel, etc.) it could happen that the
smoke discharge is not appropriate.
In that case it will be necessary to modify the parameters of work (discharge of
smoke and pellet loading) so as to comply with the real characteristics of the
chimney.
Contact technical support.
5.5.1
Chimney for smoke discharge must be made with respect to the regulations in terms of
dimensions, and in terms of materials used for its production.
COLLAPSED chimneys, made of unsuitable material (fiber cement, galvanized steel, etc.
whose interior is smooth and porous) are illegal and call into question good functioning of
the stove.
Smoke discharge through a traditional chimney (Figure 5.5.1) can be done only if the
following rules are observed:
- Inspect the state of the chimney; in case of the old chimney, it is
advisable to carry out its sanitation by importing of steel pipes insulated in
the proper manner (steel wool, vermiculite).
- Smoke can be extracted directly into the chimney which is equipped with
the access eye.

16
Fig.5.5.4
Fig.5.5.5
A) Wind damper
B) Chimney
C) Hermetic sealing
D) Access eye
!
-
In the case of a larger diameter chimney, it is necessary to "insert" in the
same a steel pipe (with a diameter that corresponds to the chimney) and
is isolated in an appropriate manner (Figure 5.5.1-2).
- Make sure the connection to the chimney in the wall is well sealed.
- Avoid contact with combustible material (wooden beams) and in any case
take care of their insulating with refractory material.
A) Vermiculite and/ or glass wool.
B) Steel pipe.
C) Cover panel.
6
INSTALLATION
Installation must be performed by qualified personnel with respect to regulations.
6.1
CONNECTING THE APPLIANCE
6.1.1
Connection to electricity
Just plug the stove using the supplied plug.

17
 Connecting to electricity (plug) must be easily accessible even after stove installment.
! If the supply cord is damaged, it must be replaced by technical assistance staff or by
qualified technicians in order to avoid any risk.
6.1.1.1
Grounding
! It is mandatory to perform grounding and set up the differential switch in line with the
applicable laws (Figure 6.1.1).
!
The metal chimney must have its own proper grounding.
Fig. 6.1.1
Fig. 6.1.2
6.1.1.2
Stove start- up
To put the stove into operation put the switch to "I" (ignition) (Figure 6.1.2)
7
START
-
UP AND USE OF STOVE
7.1
Loading pellet
The first operation that needs to be done in order to light the stove is to fill the repository with
fuel (pellet).
!
Pellets to be poured into the repository with the blades (Figure 7.1.1). Do not empty the
bag directly into the repository.

18
Fig.7.1.1
7.2
DESCRIPTION OF CONTROL PANEL
A I L G
M N F
FIG.7.2
The control panel consists of two LCD displays with backlight,
ON / OFF (D)
keys, the key to
set the operation MENU (C), four menu buttons A, B, E, F and 6 LEDs that display the state of
functioning the stove.
The panel allows the stove on and off, regulates its operation and allows adjustment of the
management and maintenance programs.
Key:
A
= Increasing the temperature
B
= Decreasing the temperature
C
= Menu set up – Verifying the parameters
D
= On/Off
E
= Decreasing power
F
= Increasing power
G
= State of display / power / parameter name
H
= State of display / clock / temperature / parameter value
I
= LED resistance ON

19
L
= LED – activated timer
M
= LED – coil operation
N
= LED – deactivation
O
= LED – room thermostat
To
access
the menu:
1) Press the
menu
key
(C)
.
2) Press the
menu
key
(C)
several times to browse different menus.
The display
G
will show Set/parametro (Settings/parameter).
The display
H
will show temperature or parameter value.
In order to confirm the values of the parameters, press the
menu
key
(C)
.
7.3
STURT
-
UP PHASE
7.3.1
Electrical power
Connect the stove to the power grid by setting the ignition switch to position “I “(paragraph
6.2).
FIG.7.3.1
If the connection is done correctly, the display is switched on and “OFF” appears on the
label furnished clock (Figure 7.3.1).

The stove operational parameters can be set only in the phase of work.
7.3.2
START
-
UP PHAS
E (ignition)
FIG.7.3.2
To light the stove, hold
On/Off (D)
for a few seconds.
FIG.7.3.3
The display will show captions “
Fan
” and “
ACC
” (ignition).
FIG.7.3.4
This phase is automatic and the stove operates it completely, so it is impossible
to modify any parameter (Figure 7.3.2).

20
Fig.7.3.5
The coil for loading pellets is powered. Starting the coil is marked by turning LED (
M
).
Fig.7.3.6
The display will show captions “
Load
” (loading) and “Wood” (wood).

Automatic ignition: the stove is equipped with an automatic device
that
allows the
burning of pellets without the use of other traditional means of ignition.
When the flame lights up, the stove starts to work.
The display will show the caption “
Fire
” and “
on
”.
! When the stove is new (or when, however, the repository is completely discharged), the
ignition may not occur because the coil for loading pellets takes a few minutes to fill and
supply the ember tray.
To solve the problem, just pour a handful of pellets in the ember tray before you press the
key ON.
In the case of poor performance or improper burning pellets in the ember tray, the ignition
alarm will start.
The display will show the captions “Alarm” and “ACC” (ignition).
Chapter Alarms will explain the procedure to unblock the stove.
7.4
PHASES OF WORK
On completed ignition, the display will show the adjusted power and room temperature.
FIG.7.4.1
Example: the display will show the captions “on 1” and “17
o
C”.
During this phase, the cooker is automatically adjusted depending on the values configured
for the power, speed of the air exchanger and the value of room temperature that was set
during the last ignition.
At this point, if necessary, operating parameters are subject to change.
THE STOVE POWER (the value set between 1 i 5).
Defines the power at which the stove works (Figure 7.4.2).
FIG.7.4.2
Press the keys (E) and (F) to increase or decrease the power. After three seconds, the
values will be automatically saved.
ROOM TEMPERATURE (the value between 7
o
C and 41
o
C)