Altronix R2416220 Series User manual

Rev. 111605 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
R2416220 Series
Rack Mount
CCTV Power Supplies
Models Include:
R2416220
- 24VAC @ 8A (200VA) or 28VAC @ 7A (200VA).
- Sixteen (16) Fuse Protected Outputs.
R2416CB220
- 24VAC @ 8A (170VA) or 28VAC @ 7A (170VA).
- Sixteen (16) PTC Protected Outputs.
Installation Guide

- 2 - R2416220 Series Installation Guide
Installation Instructions:
1. The unit is factory set for 24VAC operation.
For 28VAC operation, adjust unit prior to mounting and applying power as follows:
a. Open bottom of the unit by removing six (6) screws (Rack Mechanical Drawing & Dimensions, pg. 4).
b. Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and
the yellow wire [24V] is connected to the terminal marked [S] (Fig. 1e, pg. 3).
c. After securing all wires for proper voltage place bottom panel back on the unit and fasten with the six
(6) screws.
2. Mount unit in the desired rack location (Space unit at least 3” from any video monitors).
Do not obstruct side air vents.
3. Set power switch on the back of unit to the OFF position (Fig. 1c, pg. 3).
4. Plug power cord into a grounded 220VAC, 50/60 Hz receptacle (Fig. 1b, pg. 3), ground should be connected
as indicated in (Fig. 1d, pg. 3).
5. Set power switch on the back of the unit to the ON position and measure output voltage before connecting
devices (Fig. 1c, pg. 3). This helps avoiding potential damage.
6. Set power switch on the back of the unit to the OFF position (Fig. 1c, pg. 3).
7. Connect devices to the removable terminal blocks marked [1P & 1N through 8P & 8N] (Fig. 1a, pg. 3).
When wiring is completed on terminal blocks they can be locked down by tightening screw flanges.
8. Upon completion of the wiring, set power switch on the back of the unit to the ON position (Fig. 1c, pg. 3).
9. Green power LEDs on faceplate will illuminate when AC power is present. When an output is in a trouble
condition (blown fuse or tripped PTC) the corresponding LED will not be illuminated (Fig. 1, pg. 3).
a. Blown fuse (R2416220, R2416300220, and R2416600220) - Set power switch on the back of the unit
to the OFF position (Fig. 1c, pg. 3). Remove front faceplate to access fuses.
Replace with fuses rated @ 3.5A/250VA (Altronix model # Fuse1).
Agency Listings:
• CE European Conformity.
Input:
• 220VAC, 50/60Hz.
Output:
• Sixteen (16) fuse or PTC protected outputs.
• 24VAC or 28VAC supply current.
• Outputs are rated @ 3.5A (fuse) or 2.5A (PTC).
• Surge suppression.
Visual Indicators:
• Sixteen (16) individual power LED indicators.
• Illuminated power disconnect circuit breaker
with manual reset.
Features:
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates
costly labor.
• Removable terminal blocks with locking
screw flanges.
Rack Dimensions (H x W x D):
• 2U rack mount chassis for use in standard
EIA 19” rack.
3.26” x 19.125” x 8.5” (83mm x 486mm x 216mm)
Overview:
Altronix R2416220 Series Rack Mount CCTV Power Supplies provide 24VAC or 28VAC distributed via sixteen (16)
fuse or PTC protected outputs for powering CCTV cameras, heaters and other video accessories.
Sixteen (16) Output Rack Mount Configuration Reference Chart:
Altronix
Model Number
Output
Voltage
(VAC)
Total
Output
Current
(Power)
Number
of
Outputs
PTC
Protected
Outputs
(auto-
resettable)
Fuse
Protected
Outputs
Output
Current
(max per
output)
220VAC
50/60Hz
Input
Current
R2416220 24 8A 16 – P3.5A 1A
28 7A
R2416CB220 24 8A 16 P– 2.5A 1A
28 7A
Specifications:

R2416220 Series Installation Guide - 3 -
b. Tripped PTC (R2416CB220, R2416300220, and R2416600CB220) - To reset PTC, set power switch
on the back of the unit to the OFF position. After approximately 30 secs. set power switch to the ON
position (Fig. 1c, pg. 3).
10. Power switch with built-in circuit breaker:
OFF position - Switch not illuminated. Outputs not powered.
RESET (ON) position - Switch illuminated. Outputs powered.
Circuit breaker tripped - Switch not illuminated. Power LEDs on faceplate are not illuminated.
Outputs not powered. To reset circuit breaker set power switch to the ON (RESET) position (Fig. 1c, pg. 3).
Note: Do not exceed unit’s electrical load ratings as indicated in Sixteen (16) Output Rack Mount Configuration
Reference Chart, pg. 2.
Do not place mechanical load on the unit. Data racks should always be properly ventilated.
Unit is designed optimally for normal data room office installations.
CAUTION: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to
the National Electrical Code and all local codes.
XFMR*XFMR*
NPS
Divider
PTC1
PN
S
S P N S P N
24VAC Output
(Factory Set) 28VAC Output
28VAC (Black) 24VAC (Yellow) COM (Brown) 28VAC (Black) 24VAC (Yellow) COM (Brown)
AC Power
LEDs
Used
on PTC
models AC Power
LEDs
AC Power
LEDs
AC Power
LEDs
Removable
Terminal
Block Strain Relief
Line Cord
Illuminated
Power Disconnect
Circuit Breaker
with manual reset
Green Wire
Earth GND
Fig. 1
Fig. 1a Fig. 1b Fig. 1c
Fig. 1d Fig. 1e

- 4 - R2416220 Series Installation Guide
For fuse protected models:
Replace fuses with the same type and rating 3.5A/250V.
Rack Mechanical Drawing and Dimensions:
3.26” x 19.125” x 8.5” (83mm x 486mm x 216mm)
N PNPN PN PNPNPN PN PNPNPN PN
PN
PNPN PN P
OFF
RESET
16 15 14 13 12 11 10 98 7 654 3 21
Bottom View
Rear View
Front View
17.5” (444.5mm)
19.125” (486mm)
2.95” (75mm)
0.65” (16.5mm)
8.5” (215.9mm)
1.0” (25.4mm)
2.52”
(64mm)
1.5”
(38mm)
3.26” (83mm)
3.5A 250V
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of
sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIR2416220 Rack Mount Series K23U MEMBER