visplay Xero L P/L User manual

play it smart
XeroLP/L
Assembly and operating instructions

2
General Instructions
1/2019 (EN)
EN Visplay products are manufactured according to the
latest technology and comply with valid rules and
regulations.
Nevertheless, these products can cause injury or
damage if:
• the product is improperly installed
• the product is improperly used
• the product is improperly altered or modified
• original accessories are not used
• the safety regulations are not observed.
⚠WARNING
Each person involved in the planning, installation
and/or use of our products must be carefully read
and observe these instructions of use.
The following are of course also valid:
• Relevant accident prevention regulations
• Generally recognized safety rules
• National regulations – please consult Visplay if there
is a discrepancy with the Assembly manual
Safety instructions
⚠WARNING
When playing, children often incorrectly assess
danger. You must therefore make sure that your
store fittings are not used as toys.
Please pay attention to the following points:
• Structural conditions, in particular the design and
bearing capacity of walls, ceilings and floors. If
bearing capacity for the specified tractive or pressure
load cannot be achieved by suitable fastening or
stabilising elements, please refrain from installation.
• All the structural components supplied for stabilising
structures are to be used in an unrestricted manner
and must not be removed.
• The products may only be loaded after all the
installation steps have been completed.
• Merchandise supports should be loaded as evenly as
possible.
• Avoid loading in fits and starts.
• The maximum weight loads is to be observed. This can
be found in the instructions on assembly and use, as
well as in our sales documentation.
• Furniture with castors is generally much more unstable
than furniture with glides. Tall, heavy structures on
castors should thus be avoided.
• The recommendations of your safety ocer should
also be observed.
General care for chrome, silk and pearl
In clothing retail applications, frequent dragging of
clothes hangers along the surface can cause slight
abrasion to their hooks. This eect is most pronounced
- more so than with front-on horizontal or inclined-pole
displays - where garments are hung side-on such that
hangers have to be moved more frequently. To prevent
garments from becoming soiled, cleaning of the hanging
rods is essential.
This abrasion can be considerably reduced by using a
coat hanger cover (scliss, 929-449.02).
No responsiblity can be accepted for damage caused by
soiling, as the above mentioned abrasion depends on the
material of the coathangers in use.
With powder-coated surfaces subject to frequent use,
use of special paints is recommended. We will be happy
to advise you.
Use and care of merchandise supports
with anodised aluminium surfaces
Visplay merchandise supports with anodised aluminium
surfaces are hard-wearing. However, the exchange of
accessories might cause slight marks on the surface.
Accessories with plastic inserts usually cause less wear or
none at all.
To remove the marks, we recommend using cleaning
agents ranging from pH 5–8 (do not use any detergents
with acidic or alkaline reaction). Clean by washing the
surfaces using a sponge and water containing a wetting
agent. Then remove any loose or greasy dirt. Rubbing
o the surfaces with detergent using pure cotton waste
or porous cleaning tissue and applying the necessary
pressure in rubbing direction will remove the marks.
Aluminium profiles with widths exceeding  mm must
be subjected to abrasive cleaning using detergents
specifically developed for this purpose. The cleaning
agents developed for abrasive cleaning contain very
finely ground neutral polishing agents and have to
be adapted to the oxide layer. Alternatively, cleaning
can be carried out using an abrasive fibrous web (e.g.
Scotch-Brite, type A, red, fine or very fine) in combination
with a non-abrasive detergent.
Subsequently, residual cleaning agents should to be
rinsed o using a sponge and clear water. Then rub o
the part with a chamois.

3
Xero L P/L
349-060.19
349-061.19
red
blue
6.1
4.2
138-978.19 (75 W) 138-979.19 (EU)
138-980.19 (UK)
NV (24 V)
L = 500 mm
100–240 V
L = 200 mm
ø 7.7 mm
220–240 V
L = 1800 mm
1/2019 (EN)1/2019 (EN)
EN
TECHNICAL DATA SHEET XEROLP/L
XeroLP/L electrification in detail: conductor rail with power supply, integrated into system support profile.
Correct functioning and safety are guaranteed when properly used. No liability is accepted in event of improper use. Product safety
is based exclusively on the use of original Xero L P/L and XeroTwinP/L accessories from Visplay.
No alterations may be made, for safety reasons; the only exception being the shortening of profiles from the right-hand side.
The safety instructions of the assembly instructions must be followed as well as the instructions on the labels of the individual parts.
The indicated nominal current (A) may not be exceeded.
In event of improper use or cleaning with liquids, a risk of electric shock exists due to possibly exposed live parts. Always disconnect
from power before cleaning or servicing.
If rails or adapters exhibit visible signs of damage, disconnect them immediately and inform your service technician.
Product safety
Converter 24 V for electrified profile
Converter 75 W with input voltage 100–240 V / mains frequency:
50–60Hz / electronic protection against overheating and short-
circuit.
- Mains connection with connector for mains cable
- Nominal voltage =24V / SELV
- Safety class 2
Single power adapter 24 V
Single power adapters can be used with the XeroLP/L and Xero Twin P/L systems. Low
voltage lighting and low voltage appliances may only be connected by trained personnel.
If multiple adapters and appliances are used, their total power consumption may not exceed
the specified nominal current or fuse rating. The permissible nominal voltage and nominal
current are also limited according to the adapters used (see printed label and safety
information).
Permissible nominal current max. 4A.
Only use Xero L P/L and XeroTwinP/L system accessories! Do not use any other parts.
The user is responsible for ensuring that any connected equipment is electrically, mechanically and thermally compatible with the conductor rail.

4
Xero L P/L
1 2
UK
EU
3
32
1
Xero L P/L Xero Twin P/L Xero Twin P/L Xero L P/L
23
30
60
L = 500180 L = 200
1/2019 (EN)
EN
Check the power consumption of electrical appliances! Their maximum power consumption should be 10% below the nominal power of the
transformer.
Visplay connection system
Powering with 75 W transformer
Powering with 150 W transformer
Dimension of 75 W LED transformer
1 Visplay 24 V distributor, 8 way
2 Visplay LED transformer
3 Visplay mains cable 220–240 V

5
Xero L P/L
606/981/1231 ±0.5
Xero L P/L
638.5/1013.5/1263.5 ±0.25
A 617.5/A 992.5/A 1242.510.5
16
10.5
16
19
16.25
26.3
1200 / 2400 / 3000 / lto ± 1
2
2
27
49
49
15086.5
ø 5.6
2
30
ø 13
16
39
2
45.5
17.2
L = 2000
1/2019 (EN)1/2019 (EN)
EN
Assembly dimensions for 1 axis: XeroLP/L profile set electrified
Assembly dimensions / Layout
Xero Twin P/L profiles can be screwed in cabinets or on panels.
The accessories with fixed axis distance from Xero L P/L and Xero Twin P/L can be used.
Please observe the indications concerning weight loading and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.
All fastening points are to be used in event of maximum loads!
End caps must be fitted on profile with conductor rail.
Width of rear panel
Total length (with power supply and end cap)
Start of slot

6
Xero L P/L
Xero Twin P/L
Xero L P/L Xero L P/L
Xero Twin P/LXero L P/L Xero L P/L
606.5/981.5/1231.5 ±0.5
1276/2026/2526 ±0.3
A 617.5/A 992.5/A 1242.5
16
A 617.5/A 992.5/A 1242.5
606.5/981.5/1231.5 ±0.5
10.5 10.5
1200/ 2400 / 3000 / lto ± 1
2
2
27
49 49
15086.5
ø 5.6
2
30
ø 13
16
19
16.25
26.3
16
39
45.5 2
17.2
Xero Twin P/LXero L P/L Xero L P/L
L = 2000L = 2000
1/2019 (EN)
EN Assembly dimensions for 2 axis: XeroLP/L profile set electrified and Xero Twin P/L profile electrified
Width of rear panel Width of rear panel
Total length (with power supply and end cap)
Start of slot
The electrical components and end cap must be removed before a profile is shortened.
Always shorten a profile from the top side and trim the edges.
Make sure that all shavings are removed from the profile.
The electrical components and end cap must then be fitted back onto the profile.
Shortening a profile

7
Xero L P/L
1. 2. 3.
580
890
1140
332-420.05/.06 580 mm (3000K/6W)
332-421.05/.06 890 mm (3000K/10W)
332-422.05/.06 1140 mm (3000K/13W)
332-436.05/.06 580 mm (4000K/6W)
332-437.05/.06 890 mm (4000K/10W)
332-438.05/.06 1140 mm (4000K/13W)
349-065.12/.26/.07
red
blue
349-182.07/.26/.07
1/2019 (EN)1/2019 (EN)
EN
Weight loads
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please note that max. permissible load decreases as the merchandise support increases in length.
Please note that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise sup-
ports result in an uneven overall appearance of the goods display.
Please note that the weight limit can be reduced considerably when mounting in glass and sheet metal.
The max. permissible load of the Xero L P/L depends on the nature of the wall, the number of fastening points as well as the fastening
material used. All fastening points are to be used in event of a maximum weight load.
Please also observe the weight loads indicated in our sales documentation.
Max. load
Profile per  mm kg
Shelf frame with LED lighting for wooden or glass shelf  kg
Brackets with/without single power adapter  V for wooden shelf  kg
Attaching the glass shelf
The merchandise support has a slight slope (approx. 2°)
Production drawings of wooden shelves are available for
downloading on www.visplay.com or can be received on request.
Drawing no. 229-120
Production drawings of wooden shelves are available for
downloading on www.visplay.com or can be received on request.
Drawing no. 252-821
Wooden shelf for brackets with single power adapter
Wooden shelf for brackets

8
Xero L P/L
1/2019 (EN)
EN