ALZO Porta Flash Mini User manual

2/27/2016 ALZOPortaFlashSoftboxAssembly
http://www.alzodigital.com/customer_support/assy_alzo_porta_flash_softboxshopify.htm 1/4

ALZOPORTAFLASHSOFTBOXASSEMBLY
Figure1
AssemblingtheALZOPortaFlashMiniSoftboxis
veryfastandsimplewhenyoufollowthese
instructions.
Youwillneeda3ftx3ftcleancleartable
spacetoassembletheALZOPortaFlash
softbox.
Thesoftboxconsistsof4parts:
1.WireframeSoftbox
2.Ring
3.Flashmountbracket
4.Diffuser
Figure2

STEP1:ASSEMBLESOFTBOX
Openthesoftboxbyinsertingahandinsidethe
foldedsoftboxpushingonthewireframeinthe
fabricuntilitpopsopen.Setitonatablefacing
you.Laythediffuserinfrontofthesoftboxwith
theVelcrohookssidefacingup,Rolltheback
edgeofthediffuserandattachthediffuseredge
tothebottominteriorVelcrostripinsidethe
softbox.
Nowpullthecenterfrontedgeofthediffuserup
andattachittothecenterupperinteriorVelcro
stripofthesoftboxasshownbelow.

2/27/2016 ALZOPortaFlashSoftboxAssembly
http://www.alzodigital.com/customer_support/assy_alzo_porta_flash_softboxshopify.htm 2/4
 

Usingthefollowingsequenceattachthe
remainingedgesofthediffusertotheinterior
Velcrostripsinthesoftbox.
 
Figure3
STEP2:ASSEMBLEBRACKET
Attachtheringtothebracketwiththesupplied
wingscrew(1)asshownandtightensecurely.
PositiontheHotShoemount(3)totherear
mostposition.
NOTE:TheFlashshoemount(3)canbe
removedprovidinga1/4x20screwmount.
NOTE:TheFlashshoemount(3)isinsulated.
Theflashwillrequireasynccordconnectionto
thecamera.
NOTE:Thumbscrewadjusters(2)and(3)allow
forpositioningtheringrelativetoyourflash.
Adjuster(2)setstheheightofthering,while
adjuster(3)positionsthefrontoftheflash.
Attachyourflashtotheshoemountconnected
to(3).Adjust(2)and(3)suchthattheflash
faceenterstheopeningintheringorrestsup
againsttheringsurface.Thenremovetheflash
andtightenthethumbscrews.Hotshoemount
(3)canberotatedtoallowfrontorrearentryof
flashhotshoemount.
 
Attachthebrackettotherearofthesoftbox
(flashremoved)byslippingtheringunder3of
thewireframeprotrusionsandpryingupthe
lastprotrusion.

2/27/2016 ALZOPortaFlashSoftboxAssembly
http://www.alzodigital.com/customer_support/assy_alzo_porta_flash_softboxshopify.htm 3/4
Figure4
STEP3:ATTACHFLASH
Loosenthethumbscrew(3),attachtheflash,
adjustpositionofflashandtighten(3).The
entireassemblycannowbesetontopofthe
ALZODigitalFlipBracketorlightstand.
NOTE:TheFlashshoemount(3)canbe
removedprovidinga1/4x20screwmount.

FOLDINGandSTORINGtheALZOPortaFlashMiniSoftbox


2/27/2016 ALZOPortaFlashSoftboxAssembly
http://www.alzodigital.com/customer_support/assy_alzo_porta_flash_softboxshopify.htm 4/4
Theninsertintozipperedcase