Amano Grandstream HT503 Instruction Manual

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
1
1
Grandstream HT503
Configuration Guideline
Version: 1.0
As of 10/11/2014- FD
© 2014 - Amano Europe n.V.

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
2
2
Table of Content
1INTRODUCTION ............................................................................................................................3
2ABOUT THIS DOCUMENT...............................................................................................................3
3REMARKS .....................................................................................................................................3
4HOW TO CONNECT TO THE DEVICE FIRST TIME ..............................................................................4
4.1 WEBINTERFACE LOGIN ....................................................................................................................4
5CONFIGURATION OF GRANDSTREAM DEVICE ................................................................................5
5.1 BASIC SETTINGS .............................................................................................................................5
5.1.1 NETWORK CONFIGURATION 5
5.1.2 EXTERNAL CALL FORWARD 5
5.2FXO PORT....................................................................................................................................7
5.2.1 CONFIGURE PBX (XPARC SERVER) 7
5.2.2 PSTN CALL CONFIGURATION 8
5.2.3 FXO TERMINATION SETTINGS 9
5.2.4 CHANNEL DIALING CONFIGURATION 9
6CONFIGURATION OF XPARC SERVER (VIA XOFFICE)...................................................................... 10
6.1 XPARC MODULE ..........................................................................................................................10
6.2 CONFIGURATION PARAMETERS........................................................................................................10
6.3 ACTIVATE CONFIGURATION ............................................................................................................10
6.4 CONFIGURE INTERCOM FORWARDING ............................................................................................... 10
6.5 ACTIVATE TARIFF ......................................................................................................................... 10

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
3
3
1Introduction
This document will show how to configure a Grandstream HT503 device, which is
used to connect Xparc intercom to an analog landline (PSTN line).
2About this document
This document mainly directs to the technical staff who has to setup and configure
the device on site or on production floor. It does not contain any trouble shooting
and there is no guarantee, that the configuration shown is working in every country.
3Remarks
1. Everything explained in this document is based on a device which has default
configuration, which means only those items are mentioned that need to be
modified and are not the default setting.
2. As we could not test the settings for every country and condition, please keep
in mind that a test is mandatory before you offer this solution to a customer.

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
4
4
4How to connect to the device first time
4.1 Webinterface Login
The device is configured best by the build in webinterface and therefore needs to be
connected to your network first.
You can connect to the device using the default IP 192.168.2.1 check if this IP is
not already in use in your network.
The default password is: admin
Once logged in you are forwarded to the status page of the web interface.
In this page you have to check the firmware version as only version 1.0.8.4 is
tested and working.

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
5
5
5Configuration of Grandstream Device
5.1 Basic Settings
We start with the Basic Settings tab where you have to edit the network
configuration and set the so called „unconditional call forward to VOIP“ Which
means calls from outside are forwarded to the internal sip number configured in this
place.
5.1.1 Network Configuration
In the IP address
section you have to
enter the static IP
configuration for the
device.
5.1.2 External Call Forward
Once you configured the network settings, scroll down tot he bottom oft he page
and entert he VOIP number to forward external calls. Finally press the apply button
to apply changed and continue with the „FXO PORT“ tab.

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
6
6

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
7
7
5.2 FXO Port
The PXO Port configuration defines the way the internal SIP intercom call of the
Xparc devices are forwarded to the external PSTN line.
5.2.1 Configure PBX (Xparc Server)
First we setup the device to connect as a SIP client to the Xparc PBX.
To make configuration more compfortable, there is a fixed ID 1001 which has to be
used to connect a Grandstream device to the Xparc server.
Mandatory to use
1001
as ID as only this number will be used to forward a call!
It is not neccessarry to add an intercom device fort he Grandstream and you will not find the device in
the device list!

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
8
8
5.2.2 PSTN Call Configuration
In this section you have to adjust the PSTN behaviour according to your provider or
countries requirement.
The example is showing Belgium. Please check the requirements for your Country.
An extra test before first on site installation is recommended.

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
9
9
5.2.3 FXO Termination Settings
In this section you have to edit two values shown in the screenshot below.
5.2.4 Channel Dialing Configuration
In the Channel Dialing section we have to modify, if the device will wait for a dial
tone and if 1 or 2 stage dialing has to be used. This of course depends on the
telephone line or telephone system the port is connected to. The configuration you
find below is showing a typical configuration if the device is directly connected tot
he telephone line oft he provider. This usually does not require a pause before
dialing and 1 stage method can be applied which means that all digits required to
route the call is send in one go.

AMANO Europe NV, Westerring 2, 3600 Genk, Belgium
Tel: [phone], Fax: [phone]
Configuration Guideline HT503
10
10
6Configuration of Xparc Server (via Xoffice)
The Xparc server also need to know that the Grandstream FXO is used for intercom
forwarding. The following steps have tob e taken to enable the device in your Xparc
system.
6.1 Xparc Module
You have to enable Xparc module 109 (Intercom forwarding to analog line)
When enabled the system will automatically configure the Xparc PBX to allow the ID
1001 to connect.
6.2 Configuration Parameters
You also have to configure 2 configuration parameters.
1) Set parameter 2to HT503
2) Set parameter 3to Intercom forward by Asterisk
6.3 Activate Configuration
Activate configuration to make new configuration active and logout in Xoffice.
6.4 Configure Intercom Forwarding
Once the parameters are set as explained above and activated you have to logout
and login at Xoffice to see the new menu layout for intercom forwarding.
Now configure the telephone numbers you want to forward the calls to as usual in
the Intercom Forwarding menu.
6.5 Activate Tariff
Finally activate tariff and test the forwarding