Amazon blink XT2 User manual

Start
Here
Quick Start Guide

Page 2Page 3
Thank you for purchasing the
Blink XT2!
You can install the Blink XT2 in three easy steps:
To install your camera or system, you can:
Download the Blink Home Monitor App (page 4)
Connect your Sync Module (page 4)
Add and position your camera(s) (page 6)
Follow the in-app instructions as directed.
Follow the steps listed in this guide.
For more detailed instructions and/or how to
customize your experience, scan the QR code or
visit: support.blinkforhome.com
Step 1:
Step 2:
Step 3:
•
•
•
If you’re adding a new system, go to Step 1 on page 4for
instructions on how to add your system.
If you’re adding a camera to an existing system, go to
Step 3 on page 6for instructions on how to add your
camera(s).
Before you begin, please make sure you have the
following minimum requirements:
A mobile device running the minimum software
requirement. You can check the latest software
requirements by going to:
blinkforhome.com/requirements
Home WiFi Network (2.4GHz only).
Internet access with upload speed of at least
2 Mbps.
–
–
–
How to get started:
•
•
•

Page 4Page 5
Download and launch the Blink Home Monitor App
on your phone or tablet through the Apple App Store,
Google Play Store, or Amazon App Store.
Create a new Blink account.
In your app, select “Add a System”.
Follow the in-app instructions to complete
Sync Module setup.
Note: The Sync Module is required for your cameras to
function.
Blink Sync Module
Step 1: Download the Blink Home Monitor App
Step 2: Connect Your Sync Module
A.
B.
A.
B.
Connectivity between the camera and the Sync Module is
optimized when positioned within 100 ft of each other.
* WiFi range is dependent on conditions.
Distance between Blink devices and WiFi can vary.
*

Page 6Page 7
In your app, select “Add a Blink Device” and choose your
camera.
Remove the camera’s back cover by pressing the latch
in the center downward and simultaneously pulling the
cover away from the camera.
Insert included 2 AA 1.5V non-rechargeable lithium metal
batteries.
Leave the back cover o and continue with in-app
instructions to complete setup.
Step 3: Add Your Camera(s)
A.
B.
C.
D.
Place your camera in your desired location and go to
camera settings to check that the WiFi and Sync Module
signal strengths are strong.
Start a live view in your Blink app and adjust your
camera’s position as needed to make sure you’re seeing
what you want.
Note: Motion detection is optimized to detect when a
subject moves across the eld of view horizontally rather
than directly toward or away from the camera.
Positioning
A.
B.
BBC
1.5V AA
lithium
batteries
XT2
Camera
Latch
Push
Best performance
Camera
view

Page 8Page 9
Attach the mount (and if needed, optional extender)
to the wall using the provided screws in your desired
position.
Snap the center hole on the back of the camera onto the
circular portion of the mount.
Once mounted, you can angle the camera to adjust your
eld of view.
Your mounting kit includes: screws (2), a mount (1), and a
mount extender*(1).
* Note: The mount extender is optional. It helps increase the
range of motion of the camera once it’s mounted.
Mounting
A.
B.
C.
B
A
XT2 Back
Mount
Mount Extender (Optional)
Mount Extender (Optional)MountScrews

Page 10 Page 11
If you are experiencing trouble or need help with your Blink
XT2 or other Blink products, please contact our support
team (available 24/7) through any of the following options:
Your opinion matters and you can show others how Blink
could help them by sharing your experience through any of
the following options:
To view support articles go to:
support.blinkforhome.com
Contact us by going to the hamburger menu ( ) in
the app, tapping ‘Contact Customer Support’ and then
pressing the blue ‘Call Tech Support’ button.
To open a ticket online, visit: ‘support.blinkforhome.com’
and select ‘contact us’ in the top right corner of the page
to submit a request form.
Call us directly at: 781-332-5465
Having trouble? Enjoying your Blink XT2 system?
•
•
•
•
Leave us a review from where you purchased.
Share your experience with the Blink community at:
community.blinkforhome.com
Send us your best user videos via social (@blinkforhome) or
email ([e-mail])! We love seeing what our
users catch on their Blink cameras.

Page 12 Page 13
Individual camera arm/disarm
Individually arm or disarm cameras when your
system is armed to detect motion by tapping
the running man icon above each camera. The
camera is armed when the icon is blue and
disarmed when gray.
Scheduled system arming
To set your system to automatically arm or
disarm, select “scheduling” in the system name
dropdown menu of the app, then tap the plus
sign to set dates and times via the clock.
Live view recording
Automatically record and save live views from
your XT2 camera(s) by toggling on “Save all
XT2 Live Views” in the system name dropdown
menu at the top of the app home page.
Blue recording light
Remove the back cover of your camera(s) to manually switch
the blue “REC. LED” to either “ON” (blue light will turn on
when camera records or streams video) or “OFF” (light will
not turn on to indicate when in use) by using tweezers or a
similar tool.
Make the most of your system
Here are some additional features that come with your
system:
XT2 Back (no cover)
O n / o 
switch
XT2 Back Cover

Page 14 Page 15
from the battery comes into contact with skin or clothes, ush with
water immediately.
Insert the batteries in the proper direction as indicated by positive
(+) and negative (-) markings in battery compartment. It is highly
recommended to use Lithium batteries with this product. Do not mix
used and new batteries or batteries of dierent types (for example,
Lithium and alkaline batteries). Always remove old, weak, or worn-
out batteries promptly and recycle or dispose of them in accordance
with Local and national disposal regulations.
Other Safety and Maintenance Considerations
Your Blink XT2 can withstand outdoor use and has been tested to
withstand water projected through a 6.3mm nozzle at a volume
of 12.5 liters per minute and a pressure of 30 kPa at a distance
of 3 meters for at least 3 minutes. However, Blink XT2 is not
intended for underwater use and may experience eects from
exposure to water. Do not intentionally immerse your Blink XT2
in water or expose it to liquids. Do not spill any food, oil, lotion, or
other abrasive substances on your Blink XT2. Do not expose your
Blink XT2 to pressurized water, high velocity water, or extremely
humid conditions (such as steam room).
1.
WARNING: FAILURE TO READ AND FOLLOW THESE
SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC
SHOCK, OR OTHER INJURY OR DAMAGE
Important Safeguards:
Lithium Battery Safety Information
The Lithium batteries accompanying this device cannot be
recharged. Do not open, disassemble, bend, deform, puncture, or
shred the battery. Do not modify, attempt to insert foreign objects
into the battery or immerse or expose to water or other liquids. Do
not expose the battery to re, explosion or other hazard. Promptly
dispose of used batteries in accordance with applicable laws and
regulations. If dropped and you suspect damage, take steps to
prevent any ingestion or direct contact of uids and any other
materials from the battery with skin or clothes.
If a battery leaks, remove all batteries and recycle or dispose of them
in accordance with battery manufacturer’s recommendations. If uid
Safety and Compliance Information Use Responsibly.
Read all instructions and safety information before use.

Page 16 Page 17
FCC Compliance Statement (USA)
This Device (including related accessories like the adapter) complies
with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) such Device may not cause harmful interference,
and (2) such Device must accept any interference received, including
interference that may cause undesired operation.
The party responsible for FCC compliance is
Amazon.com Services, Inc.
410 Terry Ave North, Seattle, WA98109 USA
If you wish to contact Blink please go to this link
www.blinkforhome.com/pages/contact-us
Device Name: Blink XT2
Model: BCM00200U and BCM00201U
Power adapter designed only for use with Sync Module.
This device is designed to operate in a particular region and is
not intended to be used or distributed outside of that region.
7.
8.
To protect against electric shock, do not place cord, plug, or
device in water or other liquids.
Your Sync Module is shipped with an AC adapter. Your Sync
Module should only be used with the AC power adapter and USB
cable included in box. To reduce the risk of re or electric shock
when using the AC adapter, carefully follow these instructions:
2.
3.
•
•
•
•
Do not force the power adapter into a power outlet.
Do not expose power adapter or its cable to liquids.
If the power adapter or cable appears damaged, discontinue
use immediately.
Power adapter designed only for use with Blink devices.
Closely supervise children when the device is used by or near
children.
Only use accessories that are recommended by the
manufacturer. Use of third-party accessories may lead to
damage of your device or accessory and may cause re, electric
shock, or injury.
To avoid risk of electric shock, do not touch your Sync Module or
any wires connected to it during a lightning storm.
4.
5.
6.

Page 18 Page 19
Blink Terms & Policies
BEFORE USING THE BLINK DEVICE, PLEASE READ THE TERMS
FOUND AT HTTPS://BLINKFORHOME.COM/PAGES/BLINK-TERMS-
WARRANTIES-AND-NOTICES AND ALL RULES AND POLICIES FOR
THE DEVICE AND SERVICES RELATED TO THE DEVICE (INCLUDING,
BUT NOT LIMITED TO, THE APPLICABLE BLINK PRIVACY NOTICE
AND ANY APPLICABLE RULES OR USAGE PROVISIONS ACCESSIBLE
THROUGH THE HTTPS://BLINKFORHOME.COM/PAGES/BLINK-
TERMS-WARRANTIES-AND-NOTICES WEBSITE OR THE BLINK APP
(COLLECTIVELY, THE “AGREEMENTS”). BY USING THE BLINK DEVICE,
YOU AGREE TO BE BOUND BY THE TERMS OF THE AGREEMENTS.
Your Blink device is covered by a one year Limited Warranty. Details
are available at ‘https://blinkforhome.com/pages/blink-terms-
warranties-and-notices’.
© 2019 Amazon.com, Inc. or its aliates. Amazon, Blink, and all
related logos are trademarks of Amazon.com, Inc. or its aliates.
Product Specications Blink XT2
Model Number: BCM00200U and BCM00201U
Electrical Rating: Power: 2 1.5V AA Single Use Lithium Metal batteries
and optional (not included) USB 5V 1A external power supply
Operating Temperature: -4 to 113 degrees F
Product Specications Sync Module
Model Number: BSM00203U
Electrical Rating: 100-240V 50/60 HZ 0.2A
Operating Temperature: 32 to 95 degrees F
Other Information
For additional safety, compliance, recycling, and other important
information regarding your device, please refer to the Legal and
Compliance section of the Settings menu on your device. 
Product Disposal Information
In some areas, the disposal of certain electronic devices is regulated.
Make sure you dispose of, or recycle, your device in accordance with
your local laws and regulations. For information about recycling your
device, go to ‘http://www.amazon.com/devicesupport’.