American Aldes TTW – 100 Manual

Internal Fan
Switch
(not found on
all models)
Disconnect per
NEC or local code
(Black)
(Green)
(White)
MODEL VOLTS MAX AMPS MAX WATTS
TTW-100 120 0.22 19
TTW-100M 120 0.22 19
TTW-100H 120 0.22 19
ELECTRICAL DATA
Provide disconnect switch in vicinity of fan to permit
servicing fan in accordance with NEC and local codes.
FIELD WIRING
Local Switch
The units are axial fans designed for exhaust
ventilation of small and medium sized rooms.
Fans are made of white plastic.
Package includes:
-Fan
- Adjustable sleeve
- Exterior gravity louver damper
- Screws with anchors
- User manual
Installation Options are shown in figures 1-2.
Electrical data and connections are shown in
figure 3.
Fans are compatible with 5” (125mm) duct
openings. Fans can be mounted horizontally or
vertically, (Figures 1-2): through the wall,, to the
ceiling, into a ventilation shaft, or to round duct.
Models ending in “M” include occupancy/motion
sensor so that the fan automatically turns off
when the room is unoccupied after a specified
amount of time (adjustable from 2-30 minutes).
Input: 120V AC 60Hz.
Mounting and connection are shown in figures 1-
3. Fans are designed for long-term continuous or
intermittent operation. Airflow direction is
indicated on the fan case. Fans can be operated
at ambient temperatures between -40 to 170oF.
Protection rating from access to dangerous parts
and water penetration of the TTW-100 is IP34.
Some models may differ slightly from those
described in this manual.
WARRANTY
The TTW-100 fans are ETL listed and labeled to meet U.S.
and Canadian standards.
Manufacturer guarantees normal operation of the unit for
1 year from the date of sale subject to the fulfillment of
transport, storage, installation, and operating
specifications.
If proof of sales date is absent, warranty period is
calculated from the production date.
In the occurrence of failure due to faulty equipment
during the warranty period, the consumer has the right to
exchange it.
The unit can be exchanged by contacting the
manufacturer at following address:
American Aldes Ventilation Corporation
4521 19th Street Court E., Bradenton, FL 34203
Phone: [phone]
Email: [email protected]
Manufacturer is not responsible for damages resulting
from the unit or by gross mechanical alteration.
www.americanaldes.com
Figure 3
3166456

TTW – 100
Through The Wall Fan
Installation and
Maintenance
Manual
www.americanaldes.com
Cord set not included on all models.
Adjusting the timer and de-humidistat (not available on all models)
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, INJURY TO PERSONS, READ THE INSTRUCTIONS
CAREFULLY.
1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the
manufacturer.
2. Before servicing or cleaning the unit, switch off the power at the service panel and lock it to prevent
power from being switched on accidentally. When the power can not be locked securely, fasten a
prominent warning device such as a tag to the service panel.
3. Installation work and electrical wiring must be done by qualified person(s) in accordance with all
applicable codes and standards, including fire codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gasses through the flue (chimney) of
fuel burning equipment (if present) to prevent back-drafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as those published by the National Fire Protection
Association (NFPA), and the American Society for Heating, Refrigeration and Air-conditioning Engineers
(ASHRAE), and the local code authorities.
5. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other concealed
utilities.
6. Fans with ducts must always be vented to the outdoors.
7. This unit may have sharp edges. Use caution to avoid being cut while installing and cleaning.
8. This unit must be grounded.
CAUTION!
1. For general ventilation use only. For use in non-fire rated installations only. Do not use to exhaust
hazardous or explosive materials or vapors. Do not install in a cooking area.
2. Install in interior wall, at least 7 feet above the floor.
3. To avoid motor damage and/or noise from an imbalanced impeller, keep drywall spray, construction
dust, etc. off power unit.
4. Before installation inspect fan housing for loose parts resulting from shipping and handling that may
cause damage when fan is operated.
5. Please read the specification label on the product for further information and requirements.
6. Not for installation by children or any person who is unable to follow these safety guidelines.
7. Provide separate wall switch rated for motor duty, 120V 1A.
8. Do not close or block unit inlets and outlets in order to allow optimal air passage. Do not sit or put
objects on the unit.
9. Before installation the fan must be properly stored indoors and protected from water damage.
3166456
ttw-100_fan_iom_0510