American Dream Products E-Z Stitch User manual

Attaching Feet and Ankles to LegsStep 1 - Identify and Place FeetBoth Feet (B) are identical with each having a longer and shorter end (as measured from nearest brass inset. On a flat surface, place each foot so that they are mirrored with shorter ends closest together. rearrearfrontfrontParts:(A)2Legs(B)2Feet(C)2Ankles(D)4Cross Braces(E1) 1Right Arm(E2) 1Left Arm(F)2Elbows(G)2Side Bars, 10 inch(H)82½” Threaded Bolts(I)23” Threaded Bolts(J)23½” Threaded Bolts(K)41½” Phillips Head Bolts(L)22” Phillips Head Bolts(M)32Knobs(N)230” Scroll Rods(O)13 yd E-Z StitchTape for FabricFloor StandAssembly InstructionsAABBCCDDDDE2E1FFGGTool Needed:Page 1LongerBB
ShorterShorter
Longer

Step 2 - Identify and Place each Leg and AnkleBoth Legs (A) and Ankles (C) are identical. Identify the outside of each Leg (A) indicated by the single hole left of center. Place the end-hole of Leg (A) over the center brass inset of each Foot (B). Place each Ankle (C) over brass inset of Leg (A) and rear brass inset of Foot (B) as shown. Side Viewsingle hole(left of center)Leg (A) end-holeStep 4 - Attach Ankle to Foot and LegSecure Ankle (C) to Leg (A) using Bolt (K).Secure Ankle (C) to Foot (B) using Bolt (L).Repeat for each leg. frontrearfrontrearPage 2SurfaceStep 3 - Attach Foot to LegUsing Bolt (K), secure each Leg (A) to each Foot (B) BAK
LKBAC
BBAACC

Knob Tip: From this point forward you will be using a screw and 2 knobs to attach each piece together. Make sure you turn the knobs together equally so bolt is not over-extended into one of the knobs, causing knob inset to be pried loose. Page 3Attaching Cross SupportsStep 5 -Determine Length of Cross SupportsThe length of the Cross Supports will be 6 inches greater than the the Scroll Rod (N) length. For example, to configure the 30” scroll rods (included with floor stand) adjust the overlapping Cross Support pair to 36”. (hint: 36” length is acheived by overlapping all but 3 holes on each end). Scroll Rod Length
Cross Support Length
SCROLL ROD LENGTH + 6”
Step 6 - Align and connect Cross SupportsKeeping attachment bolts on top, position two Cross Supports (D) until they combine to the desired length and holes align. Insert Threaded Bolt (H) through aligned holes of each Cross Support and secure with knob (M) on each side of bolt. HHDDOrientAttachment Bolts to TopMMMMStep 7 - Connect Cross Supports to LegsWith assistance from another person to hold leg upright. Insert attachment bolt and pin, located at the ends of each Cross Support into designated holes on Leg (A). Cap the bolt with the knob (M) on the outside of the leg. Repeat untill all Cross Supports are attached.top hole (bolt)bottom hole (pin)MDAN

DDAAThe floor stand willnow stand on its own.Page 4MMMMAttachment BoltHolesAttaching ArmsStep 8 - Attach ArmsThe arm is placed on the inside of the legs (with the grove and holes facing upward) using Threaded Bolt (H), secured with 2 knobs (M). Step 7 - Connect Cross Supports to Legs(continued)

Step 8 - Attach Elbows to LegsThe elbows are placed on the outside of the legs using Threaded Bolt (H) and secured with 2 knobs. FFE2Page 5HHFFMMMMMStep 9 - Attach Elbows to ArmsNext attach Elbow (F) to Arm (E1 & E2) using Threaded Bolt (I) and two knobs.

Step 11 - Attach Scroll Frame to Arms of Floor StandUsing Thread Bolt (J) and two knobs (M), attach Scroll Frame Side Bars (G) to Arms (E1 & E2). Step 10 - Assemble the Scroll FrameIf you haven’t assembled the scroll frame, do so now. Additional instructions are included on how to assemble the scroll frame and attach the fabric. JJGGGGE2E1Page 6If you have any questions regarding your E-Z Stitch frames,please e-mail us at [e-mail] or call us at [phone].Manufactured by Embroidery Central, dba. American Dream Products, 1638 N 200 W, Logan, UT 84341 Congratulations!Your E-Z Stich Floor Stand is now ready to useNNMMMMMMMM

FRONTREARFootB12323StandardB1CAREARFRONTAFRONTREARBC321SwitchedForwardREARFRONTREARBack123ACBB321FRONTACChoose the Standard Position unless you need additional clearance around furniture or other obsticals. Configurations Each Foot (B) has three attachment locationsThe arms and elbows have adjustable locations for placement, depending on how far forward you would like your scroll frame to come toward you while stitching.Page 7