Clarke CWMWR1 User manual

ASSEMBLY & FIXING
INSTRUCTIONS GC05/12
WALL MOUNTED WOOD RACK
Model No: CWMWR1
Part No: 7640030

2
Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]
INTRODUCTION
Thank you for purchasing this CLARKE Wood Rack.
Please read this manual thoroughly and follow the instructions carefully. In
doing so you will ensure the safety of yourself and others around you, and
you can look forward to the product giving you long & satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose. Faulty goods
should be returned to their place of purchase. No product can be returned
to us without prior permission. This guarantee does not effect your statutory
rights.
ENVIRONMENTAL PROTECTION
If broken, do not dispose of this product with general household waste. This
product contains valuable raw materials and should be disposed of
appropriately at a recognised disposal facility.
GENERAL SAFETY PRECAUTIONS
NEVER load the rack with more than the maximum permitted working load.
ENSURE that the rack is installed in a location strong enough to take the
combined weight of the rack and whatever is being stored on it.
ALWAYS check for damage before use. Any damage should be properly
repaired or the part replaced. If in doubt, do not use. Consult your dealer.
ENSURE that the weight is evenly distributed across the full width of the rack.
ALWAYS keep the storage area tidy. Cluttered areas invite accidents.
ALWAYS ensure that adequate lighting is available and well positioned.
NEVER swing or climb on the wood rack.
ALWAYS fix the rack to a solid wall able to take load of 6 x 50 kg = 300 kg.
ALWAYS distribute any heavy loads evenly across the rack.
Please keep these instructions in a safe place for future reference.

3
Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]
TECHNICAL DATA
Vertical height 99.5 cm
Shelf Depth 31 cm
Max load capacity 50 kg per level (total 300 kg)
CONTENTS
2 x Vertical bars 6 x Spacers
12 x Horizontal Bars 12 x Screws
ASSEMBLY & FIXING INSTRUCTIONS
1. Insert a screw into the lowest
screw-hole in the vertical bar.
Take one of the horizontal bars
and slide it down the vertical bar
with the notch on the lower side
until it rests in position against the
screw.
2. Insert a screw into the next hole
up and install the next horizontal
bar. Repeat untill all the bars are
installed.
3. Mark the positions of the fixing
holes accurately on the wall using
the vertical bars as templates to
mark the drilling locations.
Note: The optimum distance apart
between the two vertical bars is
dependant upon the size and
weight of the objects/materials
being stored. For longer materials
or greater weight, multiple wood
racks can be used.

4. Position the spacers between the
mounting holes and the wall, and
fasten to the wall using suitable
fixings.
Note: You will need to provide screws and wall plugs of the correct type, able
to adequtely support the weight you intend to place on the rack.
5. When installing on dry-lining (stud) walls, take care to ensure fixing into a
solid structural member. Fixings should always be located in the centre of
the wall studs.
6. When installing on masonry walls, use (6mm) wall plugs. The vertical bars
of the wall rack are 41 mm thick. Therefore fixings of at least 70 mm length
are suitable. Always use suitable masonry bits and a hammer drill for
drilling into solid walls.
7. When installing on steel walled sheds, mount the wall rack in such a way
that the weight is correctly transferred to the wall structure, such as by
fixing to the vertical framework.
8. When installing on timber fencing, structural reinforcement will be required
if the fence was not designed to carry load. A combination of horizontal
and vertical supports may easily be added and the wall rack fixed using
70mm woodscrews.
SPACER
A SELECTION FROM THE VAST RANGE OF
QUALITY PRODUCTS
AIR COMPRESSORS
From DIY to industrial, plus air tools, spray guns and
accessories.
GENERATORS
Prime duty or emergency standby for business, home
and leisure.
POWER WASHERS
Hot and cold, electric and engine driven - we have what
you need.
WELDERS
MIG, ARC, TIG and Spot. From DIY to auto/industrial.
METALWORKING
Drills, grinders and saws for DIY and professional use.
WOODWORKING
Saws, sanders, lathes, mortisers and dust extraction.
HYDRAULICS
Cranes, body repair kits, transmission jacks for all types
of workshop use.
WATER PUMPS
Submersible, electric and engine driven for DIY,
agriculture and industry.
POWER TOOLS
Angle grinders, cordless drill sets, saws and sanders.
STARTERS/CHARGERS
All sizes for car and commercial use.