StarTech.com DRW110SAT User manual

Manual Revision: 10/04/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
*actual product may vary from photos
DRW110SAT / DRW110SATBK
5.25in Bay SATA Hard Drive Mobile Rack
*DRW110SATBK shown

Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.

Instruction Manual
i
Table of Contents
Introduction ...........................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Installation ..............................................................................................2
Installing Hard Drive in the Caddy...................................................................................................... 2
Installing the Bay in the PC.................................................................................................................... 3
Installing the Caddy in the Bay ............................................................................................................ 3
Removing the Drive Drawer.................................................................................................................. 4
Monitoring Your Hard Disk Drive and Drawer ................................................................................ 4
Specications..........................................................................................5
Technical Support ..................................................................................6
Warranty Information............................................................................6

Instruction Manual
1
Introduction
This high quality Removable SATA Hard Drive Drawer/Mobile Rack delivers a
convenient SATA hot-swap solution, allowing you to quickly swap Serial ATA hard
drives in and out of a computer without having to open the computer case.
Simply install the (included) drive bay into a 5.25in drive bay on the host computer,
then mount a 3.5in SATA HDD into the (removable) caddy. Connecting the SATA hard
drive to the computer is as easy as inserting the caddy into the drive bay, which can be
locked to prevent unauthorized removal of the installed SATA drive.
A suitable solution for large volume drives, the HDD drawer supports SATA, SATA II, and
SATA III-6Gbps hard drives allowing you to swap in large amounts of data in a matter of
seconds. With support for SATA HDD speeds up to 6.0 Gbps, the mobile rack/backplane
is fully compatible with RAID installations to ensure maximum performance and
versatility for enhanced storage applications.
The drive caddy features a rear panel ball bearing fan that helps keep the enclosed
drive cool, in turn helping to optimize operation while preserving drive lifespan.
To prevent damage to the hard drive(s) while being transferred in and out of the
computer, the drive caddy features shock absorbers and rubber cushioning that help
limit vibration/shock to the drive. This mobile rack is also compatible with DRW113-
series SATA hard drive caddies.
Packaging Contents
• 1 x Hard Drive Caddy
• 1 x Drive Bay
• 2 x Keys
• 1 x Screw Kit
• 1 x Instruction Manual
System Requirements
• Computer with an available 5.25 inch Drive Bay
• 1 x 7-pin SATA data cable
• Computer Power supply with available LP4 Molex power connector

Instruction Manual
2
Installation
Installing Hard Drive in the Caddy
WARNING! Hard drives and storage enclosures require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
1. Remove the caddy from the bay by lifting the handle and sliding the caddy out of
the bay.
2. Remove the top panel from the caddy by pressing the cover release button and
sliding the lid towards the back of the caddy.
3. Connect the short SATA data cable inside the drive caddy to the hard drive.
4. Attach the SATA power cable inside the drive caddy to the hard drive.
5. Gently place the hard drive in the caddy, making sure that the screw-holes on the
bottom of the hard drive line up with the holes in the caddy.
6. Firmly hold the hard drive to the shock absorber plate and use the four #6-32 x
1/4”(coarse thread) screws to mount your hard drive to the drawer from underneath.
7. Replace the top panel of the caddy.

Instruction Manual
3
Installing the Bay in the PC
WARNING! Computer parts can be severely damaged by static electricity. Be sure
that you are properly grounded before opening your computer case. StarTech.
com recommends that you wear an anti-static strap when installing any computer
component. If an anti-static strap is unavailable, discharge yourself of any static
electricity build-up by touching a large grounded metal surface (such as the computer
case) for several seconds.
1. Turn your computer o and any peripherals connected to the computer (i.e. Printers,
external hard drives, etc.). Unplug the power cable from the rear of the power
supply on the back of the computer and disconnect all peripheral devices.
2. Remove the side covers from your system and remove the front cover from an
available 5.25”drive bay (see your computer’s user manual for details, if necessary).
3. Insert the bay into the 5.25” bay slot, making sure that the screw-holes on the side of
the bay line up with the holes in the bay slot.
4. Connect a SATA data and LP4 Molex power cable to the rear of the bay from the
computer systems SATA controller and power supply respectively.
NOTE: If the drive will be hot-swapped, the SATA host controller and operating system
must both support hot-swapping. The “System” drive cannot be hot-swapped, as it
contains the operating system. Only secondary drives can be hot-swapped through
the operating system.
5. Place the cover back onto the computer case.
6. Insert the power cable into the socket on the power supply and reconnect all other
connectors removed in Step 1.
Installing the Caddy in the Bay
1. With the handle on the caddy fully raised, insert the caddy into the bay.
2. Once inserted as far as it will allow, lower the handle to rmly seat the caddy into
the bay.
3. Use the provided key to lock the caddy into the bay by turning the lock counter-
clockwise. The caddy must be locked in order for the drive to power up.

Instruction Manual
4
Removing the Drive Drawer
1. Insert the key and turn clockwise to unlock the drive drawer.
2. Lift the handle and gently pull the caddy out of the bay.
NOTE: Do not unlock the drawer when the hard drive is in use (See “Monitoring Your
Hard Disk Drive and Drawer” below). Only power down the drive when the hard drive is
idle. Once you have powered down the hard drive, wait about 15 seconds to let the
hard drive“spin down” before removing the caddy from the bay.
Monitoring Your Hard Disk Drive and Drawer
The status LED is located on the right side of the drive drawer. It is your best indication
of the hard drive’s status, and is lit when the drawer is successfully inserted and locked
into the caddy.
NOTE: It is recommended that you avoid removing a drawer during hard disk activity,
as doing so could damage the drive and/or data.

Instruction Manual
5
Specications
Number of Drive Bays 1
Host Interface SATA (pass through)
Host Connectors 1 x 7-pin SATA data male
1 x 4-pin LP4 Molex male
LEDs 1 x Power
Compatible Hard Drives 3.5in SATA
Fans 1 x 40mm (ball bearing)
Insertion Rating 3, 000
Enclosure Material Plastic
Dimensions (LxWxH) 220.0mm x 148.0mm x 41.0mm
Weight 530g

Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.

Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.