American Standard SELECTRONIC 605XTMV User manual

Installation Instructions
Installation Instructions
(In Toronto Area only: 1-905-3061093)
SELECTRONIC™
Thermostatic Mixing Valve
Certified to comply with ASME A112.18.1M
© 2005 American Standard
M968808
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
605XTMV
Specifications
Installation
Adjust Temperature
Service
Replacement Parts
1
2
3
3
4
Fig. 7d
Fig. 7a
Fig. 7e
Ins tal lati on In stru cti ons

Installation Instructions
Fig. 7d
Fig. 7a
Fig. 7e
MOUNTING
HOLES 4-1/4"
(108mm)
1-3/16"
(46mm)
5"
(126mm)
3-3/8"
(85mm)
3-3/16"
(33mm)
20"
(508mm)
1. Electronics Mixing Valve
and Enclosure
2. Supply Hoses
3. Mounting Kit
4. Installations instructions
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin. UNPACKING
1. Remove the Mixer and loose items from the carton. The picture below shows the Mixer and
all loose items after the carton has been opened.
1
TOOLS REQUIRED; Fig. 2 Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Phillips Screwdriver
4 Flat Blade Screwdriver
5 Electric Drill & 1/4" Drill Bit
6 Tape Measure
12
3
45
6
Roughing-in Dimensions
10'
Thermostatic Mixing valve
• 3/8" stainless steel compression flex
hoses, 20" length
• meets ASSE 1016
• anti-scald protection
1 42
3
Installation Instructions
Ins tal lati on In stru cti ons
(In Toronto Area only: 1-905-3061093)
SELECTRONIC™
Thermostatic Mixing Valve
Certified to comply with ASME A112.18.1M
© 2005 American Standard
M968808
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
605XTMV
Specifications
Installation
Adjust Temperature
Service
Replacement Parts
FAQ, s
1
2
3
3
4
5

Installation Instructions
Fig. 5
1. Remove the bottom SUPPLY HOSE (1) from the
SELECTRONIC ENCLOSURE (2). Fig. 3
2. Remove BOTTOM PLUG (3) from SELECTRONIC
ENCLOSURE (2). Fig. 3
3. Remove 4 screws from MIXER ENCLOSURE
COVER (2) and pull off COVER (2). Fig. 3b
4. Remove MIXING VALVE (7) from ENCLOSURE (3).
5. Install MIXER ENCLOSURE (4) under SELECTRONIC
ENCLOSURE (2) as shown in Fig. (3a). Hold the MIXER
ENCLOSURE (4) in that location and mark the four
mounting hole locations as shown. Fig. (3a)
NOTE: MIXER ENCLOSURE SUPPLY HOSES are
20" long. Distance between wall valves and MIXER
ENCLOSURE (4) must be taken into consideration.
5. The ENCLOSURE (4) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(5) supplied. If the MIXER ENCLOSURE (4) is to be
installed on a tile or plaster wall the ANCHORS (6) and
SCREWS (5) should be used.
6. For installations on drywall or tiled walls; use
ANCHORS (6) and SCREWS (5) for securing MIXER
ENCLOSURE (4) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (6) flush with face of the finished wall.
Align the MIXER ENCLOSURE (4) and Install the
MOUNTING SCREWS (5). Tighten to secure MIXER
ENCLOSURE (4) to mounting surface.
1. Install MIXING VALVE (1) back into ENCLOSURE.
2. Install FIBER SEAL WASHER (4) on MIXING
VALVE NIPPLE (3). Hold MIXING VALVE (1) in place
with one hand and with your other hand thread
SWIVEL NUT (2) onto MIXING VALVE NIPPLE (3).
Fig. 4. Use an adjustable wrench to tighten SWIVEL
NUT (2). Fig. 4a
3. Replace ENCLOSURE COVER and tighten securely.
1. Turn off hot and cold water supplies before
beginning.
2. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall
supplies. Connection on MIXER supplies are 3/8"
compression. Connect left supply to Hot and right
supply to Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten. FIG. 5
3. Faucet supplies measure 20" from the bottom of the
ENCLOSURE (3) base.
Note: If additional supply length is required, installer
must purchase parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop
as to avoid kinking.
MOUNT ENCLOSURE; Fig. 3
1
CONNECT MIXING VALVE; Fig. 4
2
CONNECT MIXING VALVE TO
WATER SUPPLIES; Fig. 5
3
2
Fig. 4 Fig. 4a
1
2
3
4
3
1
HOT COLD
2
2
ADJUSTABLE
WRENCH
WALL SUPPLIES
INSTALLATION Fig. 3
Fig. 3a
Fig. 3b
4-1/4"
(108mm)
1-3/16"
(46mm)
4
2
MOUNTING HOLES
ILLUSTRATION SHOWN
LESS MIXING VALVE
1
3
SUPPLIES
WASTE
LAVATORY RIM OR
MOUNTING SURFACE
ENCLOSURE
MOUNTING
HOLES
2
6
457
Fig. 7d
Fig. 7a
Fig. 7e
Ins tal lati on In stru cti ons

Installation Instructions
1. Adjust temperature by inserting a 4mm Hex Wrench
into hex opening in the side of enclosure. Fig. 6.
2. To decrease temperature, rotate up. (clock-wise)
3. To increase temperature, rotate down. (counter-
clockwise)
TO ADJUST TEMPERATURE;
Fig. 6
4
1. Turn off water supply.
2. Remove MIXING VALVE ENCLOSURE COVER.
3. Disconnect MIXING VALVE (1) from SELECTRONIC
ENCLOSURE (2). Fig. 7.
4. Pull MIXING VALVE (1) out from ENCLOSURE (5).
If SUPPLY HOSES (3) are not long enough to gain
access to TEMPERATURE CALIBRATION UNIT (6)
&THERMOSTATIC CARTRIDGE (4) disconnect
SUPPLY HOSES (3) from wall valves. Fig. 7a.
5. Rotate the BLACK CLAMP (7) with your finger and
pull off the TEMPERATURE CALIBRATION UNIT (6).
Fig 7b, 7c.
6. Use a adjustable wrench to unthread
THERMOSTATIC CARTRIDGE (4) from housing. Fig. 7d.
7. Remove THERMOSTATIC CARTRIDGE (4). Fig. 7e.
8. Rinse clean any debris from SCREENS (8) and
inspect O-RINGS (9) for damage. Replace O-RINGS (9)
if any damage is found. Fig. 7f.
9. Reverse above steps and reassemble MIXING
VALVE (1). Assemble MIXING VALVE (1) to
SELECTRONIC ENCLOSURE (2).
10. Assembly ENCLOSURE COVER and tighten
securley.
TO SERVICE CARTRIDGE; Fig; 7
5
3
Fig. 6
Fig. 7
TO INCREASE
TEMPERATURE
TO DECREASE
TEMPERATURE
4mm HEX
WRENCH
Fig. 7b
Fig. 7f
Fig. 7d
Fig. 7d
Fig. 7a
Fig. 7a
Fig. 7c
Fig. 7e
Fig. 7e
1
6
7
4
4
4
8
9
1
3
26, 4
5
SERVICE
ADJUST TEMPERATURE
Ins tal lati on In stru cti ons

Installation Instructions
M968808
Fig. 7d
Fig. 7a
Fig. 7e
Ins tal lati on In stru cti ons