AMG AMG5526G User manual

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 1 of 8 AMG5526G Instruction Sheet D20747-
00.doc
AMG5526G
Instruction Manual
Dual System with 2x Independent Channels each of :
[Receive Unit with one Bi-directional Data Channel and two
Uni-directional Alarms for a Singlemode Fibre Link]
The AMG5526G is a DUAL rackmount data receive unit which provides two independent channels,
each designed to receive 2 uni-directional alarms and transmit and receive 1 data signal over one
Singlemode optical fibre.
The AMG5526G is designed to plug into a third party subrack and powered by an AMG2001
standalone power supply.
The AMG5526G is designed to operate with two AMG5515 single channel or one AMG5525 /
AMG5525R dual channel transmit units in a point to point configuration. The R suffix in the partno.
indicates a rackmount configuration.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 2 of 8 AMG5526G Instruction Sheet D20747-
00.doc
Contents
Introduction 3
Unit Functional Schematic.................................................................................................................. 3
Optical Connection ............................................................................................................................. 3
Connections 4
Optical Connections Singlemode ....................................................................................................... 4
Power Connection .............................................................................................................................. 4
Data and Alarm Channel Connections ............................................................................................... 4
Front Panel Indicators 5
Power / Opto LED............................................................................................................................... 5
Low Speed Data LEDs ....................................................................................................................... 5
Alarm LEDs......................................................................................................................................... 5
Data and Alarm Channel Configuration 6
Data Channel Configuration ............................................................................................................... 6
Data Interface Connections ................................................................................................................ 7
Alarm Channel Configuration ............................................................................................................. 7
Alarm Interface Connections .............................................................................................................. 7
Physical Information 8
Dimensions ......................................................................................................................................... 8
Mounting Details................................................................................................................................. 8
Removal / replacement from / to the Case......................................................................................... 8
Safety 8
Maintenance and Repair 8

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 3 of 8 AMG5526G Instruction Sheet D20747-
00.doc
Introduction
Unit Functional Schematic
The AMG5526G provides two
independent, receive channels.
Each channel receives 1 data and 2 uni-
directional alarm signals from up to two
AMG5515 transmit units.
It also transmits 1 data signal to each
AMG5515.
The schematic diagram shows one of the
two available channels of the AMG5526G
Optical Connection
The AMG5526G connections are illustrated in the following example which shows two AMG5515
single channel transmit units together with an AMG5526G configured as a dual channel point to point
system.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 4 of 8 AMG5526G Instruction Sheet D20747-
00.doc
Connections
Optical Connections Singlemode
No. of Optical Connections..................1 per channel
Optical Fibre ........................................Singlemode
Connector ............................................SC/PC
Primary Optical Launch Power ............-10dBm
Transmit Wavelength...........................1550nm
Primary Optical Sensitivity...................-30dBm
Receive Wavelength............................1310nm
Minimum Optical Dynamic Range .......20dB.
Power Connection
Connector Type ...................................Removable 2-pin, 3.81mm, Screw Terminal
Connector Partno.................................Phoenix 1803578
Supply Voltage.....................................+12 to +15 Volts DC
Maximum Power ..................................2.5 Watts
Data and Alarm Channel Connections
No. of Data Channels ..........................1 per channel.
No. of Alarm Outputs ...........................2 per channel.
Connectors ..........................................Removable 8-pin, 2.5mm, Screw Terminal
Connector Partno.................................Phoenix 1881383
Data Interfaces ....................................RS-232, RS-422 or R-S485. Selected by slide switch inside
enclosure. *See appropriate section on how to remove the case
for access to the data switches
RS-485 – Switch Position - Top
RS-422 – Switch Position - Middle
RS-232 – Switch Position - Bottom
Alarm Output........................................Solid-state Relay, maximum 150mA at 125Vac/dc, Ron < 6.5Ω

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 5 of 8 AMG5526G Instruction Sheet D20747-
00.doc
Front Panel Indicators
Power / Opto LED
Power / Opto........................................ Green - Unit powered, Opto sync.
Red - Unit powered, no Opto sync.
Off - No power applied to unit
Low Speed Data LEDs
Data Present IN (RS485 or RS422) ....Green - logic zero (+V, -V) present on IN+, IN-
Red - logic one (-V,V+) present on IN+, IN-
Off - tri-state off or no connection on IN+, IN-
Data Present IN (RS232) ....................Green - logic zero (+V) present on input IN+
Red - logic transitions present on input IN+
Off - logic one (-V) present on input IN+
IN corresponds to the data signals being transmitted onto the optical fibre.
Data Present OUT (RS485 or RS422) Green - logic zero (+V,-V) present on OUT+, OUT-
Red - logic one (-V,+V) present on OUT+, OUT-
Off - tri-state off or no connection on OUT+, OUT-
Data Present OUT (RS232) ................ Green - logic zero (+V) present on OUT+
Red - logic transitions present on OUT+
Off - logic one (-V) present on OUT+
OUT corresponds to the data signals being received from the optical fibre.
Alarm LEDs
Channel 1
ALARM 1 OUT..................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM 2 OUT..................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
Channel 2
ALARM 1 OUT..................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM 2 OUT..................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 6 of 8 AMG5526G Instruction Sheet D20747-
00.doc
Data and Alarm Channel Configuration
The AMG5526G sends and receives data to/from up to two AMG5515 single channel or one
AMG5625 or AMG5625R rackmount equivalent dual channel transmit units. Each physical data
interface RS-485, RS-422 or RS-232 is individually selectable by the user with the corresponding slide
switch mounted on the main PCB inside the enclosure.
2 uni-directional alarms are also provided for each video channel, each of which can receive an on/off
signal from an AMG5515 and are typically used to convey contact closure status. Each alarm output
uses a Solid-state relay, with a maximum load current of 150mA at 125Vac/dc and Ron < 6.5Ω.
Data Channel Configuration
Each low speed data channel provides an RS-232, RS-422 (full duplex, four wire) or RS-485 (half
duplex, two wire) interface defined by the corresponding mode switch inside the enclosure. Every data
channel as shipped from the factory is set up for RS-485 operation unless otherwise requested.
The data input for both the RS-485 and the RS-422 modes detects a tri-state input condition by
monitoring the differential voltage level across the input. A differential level below 600mV positive or
negative will be detected as a tri-state condition. A level above 600mV positive or negative will be
detected as a logic 1 or logic 0 respectively. It is important therefore to terminate the RS-485 bus or
the RS-422 input bus using 120Ω if a pre-bias is present on the RS-485 or RS-422 bus.
A large number of third party equipment manufacturers apply a pre-bias on their RS-485 bus. This pre-
bias is applied by pulling one arm of the RS-485 bus high (+5 volts) and the other arm low (0 volts)
using high value resistors within the third party equipment. In order to ensure that the AMG equipment
detects a tri-state condition, then these resistors should have a value above 5kΩ. If the third party
bias resistors are less the 750Ω the bus can be multiple terminated as required to ensure that a tri-
state level is detected.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 7 of 8 AMG5526G Instruction Sheet D20747-
00.doc
The system detects a tri-state input condition on the data channel bus when in RS-485 or RS-422
mode.
Data Interface Connections
Data Channels 1 and 2.
Data Channel
Connector
Pin No. RS-485
[switch top]
RS-422
[switch middle]
RS-
232
[switch bottom]
1IN + (A) IN
2IN - (B)
3GND GND GND
4
5
6
7IN/OUT + (A) OUT + (A)
8IN/OUT - (B) OUT - (B) OUT
Note: (A) or (B) in brackets in the above table refers to RS-485 / RS-422 data specification.
Alarm Channel Configuration
The AMG5526 provides 2 uni-directional alarm outputs per channel.
Each alarm output provides a set of contacts from a solid state relay.
Alarm Output 1 : provides a pair of normally open, volt-free contacts.
Alarm Output 2 : provides a normally open, switched contact to Ground (0V / GND).
Alarm Interface Connections
Channels 1 & 2
Alarm Interface
Connector Pin
No. Alarm 1 Alarm 2
1
2
3ALARM 2 GND
4ALARM 2 OUT +
5ALARM 1 OUT -
6ALARM 1 OUT +
7
8

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 8 of 8 AMG5526G Instruction Sheet D20747-
00.doc
Physical Information
Dimensions
Height...................................................3U Plug-in
Width....................................................7HP
Depth ...................................................170mm excluding connectors
Weight..................................................600grams
Mounting Details
The unit is designed to be mounted within a non AMG Subrack on standard card guides.
Removal / replacement from / to the Case
Note: - The AMG unit PCB is static sensitive. Handle with proper care and use normal electrostatic
discharge (ESD) procedures. Use properly grounded protection (for example, wrist straps) when
handling the PCB out of the case.
To remove the PCB from the case for example to access a Low Speed Data mode switch, remove the
2 fixing screws on the rear panel and slide the PCB sufficiently out of the case to enable access to the
switch.
To replace the PCB into the case, slide the PCB gently into the case, if necessary aligning the board
with the appropriate slots.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:
Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at other people.
Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825-2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone [phone]
Technical Support [phone]
Email [e-mail]