Amphenol Procom XG-COMBI MOUNT User manual
GPS mount for GPS Antennas and Other Frequencies
DESCRIPTION
Mobile mount with a nice, “streamline”-look, which can be installed everywhere on the
car in an 19 mm dia. hole.
Especially suited for mounting on the narrow strip on rear wing between trunk lid and car
side.
M6 thread whip-mounting system.
Very low requirements to installation depth both under and after installation.
Designed for installation with access from the outside only.
Bendable section in mount makes whip tiltable 30° by hand.
Complete line of whips available for all communications bands up to 1300 MHz.
Mounting body made of stainless steel !
Choice between two connection principles:
XG-Combi mount: FME-connection and GPS (supplied without cable).
XGP4-Combi mount: Permanently attached 4 m RG 58 cable terminated with FME-
connector and GPS.
GPS-antenna for fixed installations.
Full hemispherical coverage.
Built-in high-gain, low-noise amplifier.
Right-Hand Circular Polarization (RHCP).
2.85 V - 5 V supply voltage (typical 3 V).
ECE R118.02 approved cable.
SPECIFICATIONS
Electrical
Model XG-COMBI MOUNT
Application Mount for mobile antennas
Mechanical
Compliance ECE R118.02 approved cable
Build-In Depth Active : 30 mm
Passive : 11 mm
Connection(s) Cable : RG 178, length 150 mm
Connector: FME-male
Materials
Black-chromed brass
Weather- and shockproof plastics
Stainless steel
Installation Torque 4 ± 1 Nm
Colour Black
Dimensions 48 mm x 28 mm (LxW) / 1.89 x 1.10 in.
Whip Connection M6 thread stud
Weight XG-version : Approx. 60 g
XGP4-version: Approx. 200 g
Mounting 19 mm dia. hole
Mounting Plate Thickness Max. 2 mm
GPS Antenna
Noise Figure (GPS Amplifier) < 1.5 dB (typical 1.1 dB)
Gain (GPS Amplifier) 22 dB -2 dB
Frequency (GPS) 1575.42 ± 1.023 MHz
Power Supply (GPS) DC 2.85 V ~ 5 V (typical 3 V)
Current Consumption (GPS Amplifier) <20 mA
Impedance (GPS) 50 Ω
A SELECTION OF THE VARIOUS WHIPS WHICH CAN BE CONNECTED TO THE
XG-COMBI MOUNT
XG-Combi Mount
Page: 1 of 3
Last edited: 2021/12/10
ORDERING
Model Product No. Description
XG-COMBI MOUNT 130002032 XG-Combi mount with FME-system
XGP4-COMBI MOUNT 130002043 XGP4-Combi mount with 4 m RG 58 cable and FME-
connector
Accessories FME-Cables
1 m FME(f) to FME(f) 130000437
2 m FME(f) to FME(f) 130000447
3 m FME(f) to FME(f) 130000457
4 m FME(f) to FME(f) 130000466
5 m FME(f) to FME(f) 130000474
6 m FME(f) to FME(f) 130000483
4 m FME(f) to FME(f), white 110000064
6 m FME(f) to FME(f), white 110000066
12 m FME(f) to FME(f), white 110000068
18 m FME(f) to FME(f), white 110000069
Accessories FME-Connectors
FME(f)-FME(f) 130000583
FME(m)-P(m) (Prolongation) 130000565
FME(m)-N(m) 130000571
FME(m)-SMA(f) 130000578
FME(m)-BNC(m) 130000566
FME(m)-TNC(m) 130000569
FME(m)-UHF(m) 130000572
FME(m)-MiniUHF(m) 130000573
FME(m)-MiniUHF(m)(Elbow) 130000582
FME(m)-BNC(m)(Elbow) 130000580
FME(m)-TNC(m)(Elbow) 130000581
FME(m)-SMA(m) 130000577
FME-SYSTEM ACCESSORIES - NOTE
For further information about other types of FME-cables and FME-connectors, please compare the cable and connector data sheets under accessories.
EU AND UK DECLARATION OF CONFORMITY
Hereby Amphenol Procom declare that the product type XG-COMBI MOUNT is in compliance with EU Directive 2014/53/EU and
the UK Radio Equipment Regulations 2017 (S.I. 2017 No. 1206).
The full text of the Declaration of Conformity is available at:
https://amphenolprocom.com/images/shop/catalog/pdf-for-catalouges/Declaration-of-Conformity-XG-COMBI-MOUNT.pdf
XG-Combi Mount
Page: 2 of 3
Last edited: 2021/12/10
INSTALLATION
XG-Combi mount antenna types can be mounted anywhere on the car, however, roof
top mounting is always recommended.
The oblong XG-Combi mount is able to be mounted on the often very narrow strip on the
rear wing between the trunk lid and the side of the car.
Mounting can take place with access from the outside or inside when drilling an 19 mm
dia. hole.
A good contact surface on the inside of the car body must always be ensured, thus
enabling the base plate to get in direct contact with the metal parts of the car, which is of
utmost importance for proper performance of the antenna.
When cleaning the car in car-washing machines, the whip is easily removed using a fork
spanner, size 9 mm. The whip is refitted again by screwing it onto the thread stud and
tightening it lightly with the spanner.
As the XG-Combi mount is internally equipped with a bendable section, the antennas
can always be adjusted to an upright position independent of the tilt angle of the
installation spot (up to 30° tilt).
1. INSTALLATION DIMENSION
ASSEMBLY INSTRUCTIONS
Put GPS-FME-connector-cable through the gasket (2).
Put the gasket (2) + GPS-part (1) over the body (B).
Put the body (B) + gasket (3) + GPS-part (1) through the ø19 mm hole.
Put the housing (4) over the body (B) and be sure that the GPS-part (1) fits into the square
hole in the body (B).
Put the threaded part over the body (B) and tighten max. 4 ±1 Nm!
Put the corrugated plastic unit (6) over the body (B).
Mount the antenna whip se figure 4.
2. INSTALLATION STEPS
Do not use sealer on rubber gasket or other places.
XG-Combi Mount
PROCOM A/S reserves the right to
amend specifications without prior notice
PROCOM A/S • Smedetoften 12
DK 3600 Frederikssund • Denmark
Page: 3 of 3
Last edited: 2021/12/10
