Amplicon Impact 1015 User manual

Part No: 85080229 issue A1
Impact 1015 1U rackmount computer user manual
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

Safety Instructions
Before you unpack your computer system, ensure you carefully read
through this manual and follow any related safety or operational
instructions.
Only suitably qualified and experienced personnel should work inside the
computer.
Before commencing work within the computer ensure that the mains is
disconnected from the computer and any attached peripherals.
Operation of your computer
Before operating your computer please:
Read the equipment ratings plate and ensure that the mains circuit is
suitably rated to power the equipment, to avoid risk of overloading. Do
not use mains adaptors, or extenders.
Ensure that any cables connecting to the equipment are made safe and
do not present a tripping hazard.
To avoid risk of electric shock ensure that equipment is plugged into a
suitably earthed mains outlet. Only use the power cord supplied with your
cut or damaged
----
Ensure the computer chassis is kept away from heat sources, such as
radiators and heating vents.
Computer chassis ventilation slots must be kept clear and not blocked.
Failure to do so is likely to cause the unit to overheat and become
unstable.
Avoid connecting the computer to an electrical supply which may have
unacceptable interruptions, surges, spikes or noise. We recommend the
use of an uninterruptible power supply (UPS), surge protector or mains
conditioner to address the problem.
computer or power supply unit. Do not continue to use the cable if it is
Electrostatic Discharge Damage
When working on the inside of a computer system, you must be aware
that many of the components are electrostatic discharge sensitive (ESD).
These components can easily be damaged if suitable precautions are not
taken. ESD damage is not always immediately apparent and may result
in a failure many weeks later. When working on equipment we
recommend the use of an ESD mat and wrist strap.
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

Chapter 1 Getting Started ..................................................................................... 1-1
System Overview ............................................................................................... 1-2
System Specifications ........................................................................................ 1-6
Mainboard Layout ................................................................................................ 1-8
Chapter 2 Hardware Setup .................................................................................... 2-1
Quick Components Guide .................................................................................... 2-2
CPU (Central Processing Unit) ............................................................................ 2-3
Memory................................................................................................................. 2-4
Power Supply ...................................................................................................... 2-6
Back Panel I/O ...................................................................................................... 2-7
Connector ............................................................................................................ 2-8
Jumper ................................................................................................................ 2-15
Slot ...................................................................................................................... 2-16
System Assembly Flowchart ........................................................................... 2-18
System Assembly .............................................................................................. 2-19
Rack Mounting .................................................................................................... 2-30
Chapter 3 BIOS Setup ............................................................................................. 3-1
Entering Setup ..................................................................................................... 3-2
The Menu Bar ...................................................................................................... 3-4
Main ...................................................................................................................... 3-5
Advanced ............................................................................................................ 3-6
Boot .................................................................................................................... 3-20
Security .............................................................................................................. 3-23
Chipset ............................................................................................................... 3-24
Exit ...................................................................................................................... 3-26
Appendix A Intel ICH9R SATA RAID ..................................................................... A-1
ICH9R Introduction ............................................................................................... A-2
BIOS Configuration .............................................................................................. A-3
Installing Driver .................................................................................................... A-9
Installing Software ............................................................................................ A-11
RAID Migration Instructions ............................................................................... A-15
Degraded RAID Array ........................................................................................ A-22
CONTENTS
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-1
Getting Started
Chapter 1
Thank you for choosing the , a
high-performance system from .
Based on the innovative Intel®3200 ICH9R chipsets
for optimal system efficiency, th ccommo-
dates the latest Dual-Core Intel®Xeon®processor 3000
series, Quad-Core Intel®Xeon®processor 3200 series,
Wolfdale and Yorkfield processors in LGA775 pack-
age and supports up to four 240-pin DDR2 667/800
DIMM slots to provide the maximum of 8GB memory
capacity.
With high scalability, reliability, ease of use, and overall
value, th makes an ideal choice for value con-
scious customers.
Amplicon Impact 1015
1U rackmount Amplicon
+
is system a
is system
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-2
System Overview
Top View
1
2Slim DVD ROM drive
3PCI pansion ot
4CPU ket (LGA775)
5DIMM ots (x 4)
61U Power Supply Unit (PSU)
7Blower
8Fan ct
6
5
2
4
3
7
8
1
Dual hotswappable HDD bays
/CD
Express ex sl
sl
soc
300W
du
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-3
Slim DVD/CDROM drive
1Slim DVD/CDROM drive
HDD bays
2
Ports
3USB ports
LEDs
4Power LED
This indicator shows the power status of the system. It glows (ON) when the
5Status LEDs of LAN1 / LAN2
1. The green LED is when there is an active connection on the LAN port.
2. This LED flashes when transmitting or receiving activities to or from the
system are detected.
6System ID LED
7System Alert LED
Front View
Front Bezel
3
79
10
8
46
5
1
2
Hotswappable Hard Disk Drive bays
ON
power is turned on.
System Overview
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-4
Front Bezel LEDs
Buttons
8System ID button
9Power button
Press this button once to shut down the system, and then once to switch on.
10 System Reset utton
LED Color State Description
Power Blue On Legacy power on/ACPI S0 state
Blue Blink Sleep/ACPI S1, S4, S5 state
Off Off Power off
LAN1/LAN2 Activity Green On LAN link
Green Blink LAN access activity
b
System Overview
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-5
Rear View
Rear Bezel
Rear Bezel LEDs
1PS/2 Keyboard/Mouse Connector 2USB ports
3Serial port 4VGA ort
5LAN Jacks
LED Color LED State Condition
Off LAN link is not established.
Orange On (steady state) LAN link is established.
On (brighter & pulsing) Thecomputer is communicating with another
computer on the LAN.
Green Off 10 Mbit/sec data rate is selected.
On 100 Mbit/sec data rate is selected.
Orange On 1000 Mbit/sec data rate is selected.
RJ45 NIC1 /
NIC2 Link Speed
(Left Side)
RJ45 NIC1 /
NIC2 Access
(Right Side)
1234 5
p
System Overview
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-6
System Specifications
Processor
processor 3200 series, Wolfdale and Yorkfield processors in LGA775
package
FSB
- 1333/ 1066/ 800 MHz
Chipset
- North Bridge: Intel 3200 chipset (Intel 3200/3210 supports PCI
Express graphics)
- South Bridge: Intel ICH9R chipset
Memory
- 4 DDR2 667/800 DIMM slots (240pin / 1.8V)
- Up to 8GB memory capacity
LAN
-
Intel 82573L Gigabit Ethernet controller (LAN1) & Intel 82566DM
Gigabit Ethernet controller (LAN2)
Floppy
- 1 floppy port
- Supports 1 FDD with 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB
IDE
- 1 IDE port by ITE IT8213F
- Supports Ultra DMA 66/100/133 mode
- Supports PIO, Bus Master operation mode
SATA
- 4 SATAII ports by ICH9R
- Supports storage and data transfers at up to 300MB/s
RAID
- Supports RAID 0, 1
.
- Support for Intel Core 2 Duo processors (default processor) and
Dual-Core Intel Xeon processor 3000 series, Quad-Core Intel Xeon
System Specifications
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-7
Graphics
- XGI Z7 graphics controller
- Onboard 16MB Video SDRAM
Connectors
Back Panel
-1PS/2mouseport
-1PS/2keyboardport
-2USB2.0ports
- 1 serial port
-1VGAport
- 2 Gigabit LAN jacks
Onboard Connectors
- 3 proprietary front panel connectors (optional)
- 3 USB 2.0 connectors (6 ports)
- 1 serial port connector
- 1 TPM connector
- 1 SPI Flash ROM connector (for debugging)
- 1 chassis intrusion connector
Slots
- 1 PCI Express x16 slot (with x8 signal)
- *1 PCI Express x4 slot
- *4 PCI slots (supports 3.3V/ 5V PCI bus interface)
Certification
- Safety: UL, CB, BSMI
- EMC: FCC Class A, CE Class A, BSMI
Chassis
- Form factor: 1U 19" rackmount
- Externally hotswappable HDD bay x 2
-SlimDVD/CDROMdrivebayx1
- Full height slot x 1
- Chassis dimension: 428(W) X 44.4(H) X 442(D) mm
Power Supply
- 300 Watt
PFC function: Yes
Form factor: SSI EPS 1U
Safety mark: UL, cUL, TUV, CE-mark, CB
(*Available on motherboard )only
PCI Express
System Specifications
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

1-8
Mainboard Layout
BATT
+
JUSB1
T: Mouse
B: Keyboard
COM1
JLAN1
LAN
Chip
XGI
Z7
JLAN 2
VGA 2
SATA2 SATA4 SATA1 SATA3
JUSB3
JUSB2
J_SATALED1
SYS_FAN2 J_CMOS1
COM2
JAPP2
JSPI1
J_IDE1
ITE
IT8213F
JUSB4
FDD 1
SYS_FAN1
JINT1
PCI1
PCI2
PCI4
DIMM_A1
DIMM_B1
DIMM_A2
DIMM_B2
PCIE1
PCIE2
CPU_FAN1
JPWR2 REAR_FAN1
JPWR1
JAPP1
PCI3
J_BOOT3
J_BOOT1
BMC
Chip
Intel
ICH 9R
Intel
3200
J_ICMB1
J_BOOT2
J1
J_SMBUS1
J_IPMB1
FRONT_FAN1
D_SATALED1 JAPP 3
J_VGA_EN1
D_SATA2
D_SATALED2
D_SATA1
FPC1
JTPM1
ATX form factor Server Board
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-1
Hardware Setup
Chapter 2
Refer to the system assembly flowchart and the chart
below to determine the proper sequence of removing
or installing components to the server.
CPU, Memory, Power Supply, Back
Panel, Connector, Jumper, Slot
Chassis Cover
CPU, Cooler
Memory
Expansion Card
Hard Disk Drives
Slim DVD/CDROM Drive
Rail Set
Rack Mounting
System Assembly
Rack Mounting
Mainboard Hardware
System
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-2
Quick Components Guide
Back Panel
I/O , p.2-7
DIMM Slots ,
p.2-4
JPWR1 ,
p.2-6
CPU_FAN1 ,
p.2-10
FDD1 ,
p.2-8
CPU , p.2-3
COM2 ,p.2-12
PCI Slots ,
p.2-16
PCI Express
Slots , p.2-16
JINT1 ,
p.2-10
JPWR2 ,
p.2-6
J_IDE1 ,
p.2-8
J_CMOS1 ,
p.2-15
SYS_FAN2 ,
p.2-10
SATA1~4 ,
p.2-9
JUSB2/3 ,
p.2-12
JAPP3 ,p.2-11
FPC1 , p.2-10
J_VGA_EN1 ,
p.2-15
JTPM1 ,
p.2-14 SYS_FAN1 ,
p.2-10
JAPP2 , p.2-11 JUSB4 ,
p.2-12
JSPI1 , p.2-13
FRONT_FAN1 ,
p.2-10
JAPP1 ,p.2-11
REAR_FAN1 ,
p.2-10
J_BOOT2,
p.2-13
J_BOOT3 ,
p.2-15
J_IPMB1 , p.2-13
J_ICMB1 , p.2-13
J_SMBUS1 ,
p.2-14 J1 , p.2-13
J_BOOT1 ,
p.2-13
D_SATA1 ,
p.2-9
D_SATALED1 ,
p.2-9
D_SATA2 ,p.2-9
D_SATALED2 ,
p.2-9
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-3
This mainboard supports dual-core Intel®Xeon®processor 3000 series, quad-core
Intel®Xeon®processor 3200 series, Wolfdale and Yorkfield processors in LGA775
package. W hen you install the CPU, make sure that you install the cooler to
prevent overheating. If you do not have the CPU cooler, consult your dealer
before turning on the computer.
Introduction to LGA 775 CPU
The surface of LGA 775 CPU.
Remember to apply some ther-
mal paste on it for better heat
dispersion.
The pin-pad side of LGA 775
CPU.
Yellow triangle is the Pin 1 indicator
Alignment Key
Important
Overheating
Overheating will seriously damage the CPU and system. Always make sure
the cooling fan can work properly to protect the CPU from overheating. Make
sure that you apply an even layer of thermal paste (or thermal tape) between
the CPU and the heatsink to enhance heat dissipation.
Replaceing the CPU
While replacing the CPU, always turn off the power supply or unplug the
power supply’s power cord from the grounded outlet first to ensure the safety
of CPU.
CPU (Central Processing Unit)
Yellow triangle is the Pin 1 indicator
Alignment Key
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-4
Empty
Installed
Memory
64x2=128 pin 56x2=112 pin
DDR2
240-pin, 1.8V
These DIMM slots are intended for system memory modules.
Dual-Channel Mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive data with two
data bus lines simultaneously. Dual-Channel mode is enabled when the installed
memory capacities of both DIMM channels are equal. If different speed DIMMs are
used between channels, the slowest memory timing will be used.
Dual-Channel mode can be achieved with two, three or four DIMMs. To achieve Dual-
Channel mode, the following conditions must be met:
* Matched DIMM configuration in each channel
* Same Density (128MB, 256MB, 512MB, etc.)
* Matched in both Channel A and Channel B memory channels
* Populate symmetrical memory slots (Slot 1 or Slot 2)
Configurations that do not match the above conditions will revert to Single-Channel
mode.
DIMM_A1
DIMM_A2
DIMM_B1
DIMM_B2
DIMM_A1
DIMM_A2
DIMM_B1
DIMM_B2
DIMM_A1
DIMM_A2
DIMM_B1
DIMM_B2
2 DIMMs
3 DIMMs
4 DIMMs
1GB
1GB
1GB
512MB
512MB
512MB
512MB
1GB
1GB
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-5
Installing Memory Modules
1. The memory module has only one notch on the center and will only fit in the right
orientation.
2. Insert the memory module vertically into the DIMM slot. Then push it in until the
golden finger on the memory module is deeply inserted in the DIMM slot.
3. The plastic clip at each side of the DIMM slot will automatically close.
Important
You can barely see the golden finger if the memory module is properly inserted
in the DIMM slot.
Volt Notch
Memory
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-6
pin 12
pin 13
Important
1. Make sure that all connectors are connected to proper power supplies to
ensure stable operation of the mainboard.
2. Power supply of 3 0 watts (and above) is highly recommended for system
stability.
24-Pin System Power Connector: JPWR2
This connector allows you to connect a 24-pin power supply. To
connect the 24-pin power supply, make sure the power supply
connector is inserted in the proper orientation and the pins are
aligned. Then push down the power supply firmly into the connector.
You may use the 20-pin power supply as well. If you’d like to use the
20-pin power supply, please align your power supply connector
with pin 1 & pin 13. There is also a foolproof design on pin 11, 12, 23
& 24 to avoid wrong installation.
8-Pin CPU Power Connector: JPWR1
This connector provides 12V power output to the CPU.
Power Supply
PIN SIGNAL
13 +3.3V
14 -12V
15 GND
16 PS-ON#
17 GND
18 GND
19 GND
20 Res
21 +5V
22 +5V
23 +5V
24 GND
PIN SIGNAL
1 +3.3V
2 +3.3V
3GND
4+5V
5GND
6+5V
7GND
8PWROK
9 5VSB
10 +12V
11 + 1 2 V
12 +3.3V
Pin Definition
JPWR2
112
24 13
JPWR1
1
8
5
4
PIN SIGNAL
5+12V
6+12V
7+12V
8+12V
PIN SIGNAL
1GND
2GND
3GND
4GND
Pin Definition
0
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-7
Back Panel I/O
LED Color LED State Condition
Off LAN link is not established.
Left Orange On (steady state) LAN link is established.
On (brighter & pulsing) The computeris communicating with another computer on the LAN.
Green Off 10 Mbit/sec data rate is selected.
Right On 100 Mbit/sec data rate is selected.
Orange On 1000 Mbit/sec data rate is selected.
Mouse/Keyboard
The standard PS/2®mouse/keyboard DIN connector is for a PS/2®mouse/keyboard.
USB Port
The USB (Universal Serial Bus) port is for attaching USB devices such as keyboard,
mouse, or other USB-compatible devices.
Serial Port
The serial port is a 16550A high speed communications port that sends/ receives 16
bytes FIFOs. You can attach a serial mouse or other serial devices directly to the
connector.
VGA Port
The DE-15 female connector is provided for monitor.
LAN
The standard RJ-45 LAN jack is for connection to the Local Area Network (LAN). You
can connect a network cable to it.
Keyboard
Mouse
LAN Jacks
Serial PortUSB Ports VGA Port
Link/Active Indicator Mode Indicator
RJ-45 LAN Jack
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-8
Floppy Disk Drive Connector: FDD1
This connector supports 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB floppy disk drive.
IDE Connector: J_IDE1
This connector supports IDE hard disk drives, optical disk drives and other IDE devices.
Connector
FD D1
J_IDE1
Important
If you install two IDE devices on the same cable, you must configure the
drives separately to master / slave mode by setting jumpers. Refer to IDE
device’s documentation supplied by the vendors for jumper setting
instructions.
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m

2-9
Seri al ATA Con n ecto r: SATA1 ~ S ATA4
This connector is a high-speed Serial ATA interface port. Each connector can con-
nect to one Serial ATA device.
SATA4
SATA1 SATA2
SATA3
Important
Please do not fold the Serial ATA cable into 90-degree angle. Otherwise,
data loss may occur during transmission.
SAS Connector: D_SATA1, D_SATA2
These connectors are designed to connect Serial ATA devices only.
SAS LED Connector: D_SATALED1, D_SATALED2
These connectors are used to connect external LEDs to show the status of the SATA
HDDs attached to the D_SATA1 & D_SATA2. The D_SATALED1 is intended for the
D_SATA1 and the D_SATALED2 is made for the D_SATA2. When a SATA HDD is
attached to the SAS connector, the LED connecting pin 1 & 2 will glow. When HDD
activity/access is detected, the LED connecting pin 3 & 4 will blink.
PIN SIGNAL
1 +3.3V
2GND
3 +3.3V
4 SATARead
Pin Definition
D_SATA1,
D_SATA2
1
D_SATALED1,
D_SATALED2
Manual
Amplicon.co IT and Instrumentation for industry
Sales: [phone] Website: www.amplicon.co Email: [e-mail]
m
m m