Ampro TECSHOW QUAD SPIDER 60 User manual

P. 1
| Tecshow Quad Spider 60
QUAD SPIDER 60
Moving LED eect
USER MANUAL / MANUAL DE USUARIO
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE
POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR

P. 2
Tecshow Quad Spider 60 |
Quad Spider 60
Moving LED eect – 6 x 4-in-1 10W LEDs
Quad Spider 60 is a moving beam eect that
sports 6 x 10W 4-in-1 RGBW LEDs divided into 2 tilt
bars. The unit has a beam angle of 4º for each one
of its LEDs. Thanks to its 15 integrated programs
and its razor sharp beams, the unit is capable of
creating incredible eects, generating various
sequences and dynamic light crossings. Quad
Spider 60 was designed to give you great exibility
with its 4 modes of operation, DMX, Master / Slave,
Auto-run and sound active.
Specications
Source & Optics
• Light Source: 6 x 10W 4-in-1 LEDs
• Average lifespan: 50,000 hours
• Beam angle: 4º
Eects and functions
• Razor sharp beams
• Strobe eect
• Pulse eect
• Adjustable speed
• 15 integrated programs
• Linear dimmer 0-100%
Control
• Operational modes: DMX, Master/Slave,
Auto-run & sound active
• Canales DMX: 10/14
Movement
• Tilt: 90º
• Adjustable speed
• Independent control of each bar
Physical
• 4-digit LED screen
• Power connector
• DMX connectors: 2 XLR connectors (XLR-3 input
& output)
• Dimensions: 225x145x150 mm. / 8.85x5.70x5.90 in.
• Weight: 2.25 Kg. / 4.96 Lbs.
1. OVERVIEW
English version

P. 3
| Tecshow Quad Spider 60
English version
In order to install, operate, and maintain the
lighting safety correctly. We suggest that the
installation and operation should be done by
the veried technician and follow the instruction
strictly.
Every person involved with the installation,
operation and maintenance of this device has to:
• Be qualied
• Follow carefully the instructions of this
manual
2. SAFETY INSTRUCTIONS
Keep this equipment away from
rain, moisture and liquids.
Caution
Unplug mains lead before
opening the housing.
Caution
3. DMX-512 CONTROL CONECTION
Be sure to follow gures two and three when
making your own cables. Do not use the ground lug
on the XLR connector. Do not connect the cable’s
shield conductor to the ground lug or allow the
shield conductor to come in contact with the XLR’s
outer casing. Grounding the shield could cause a
short circuit and erratic behavior.
When longer runs of cable are used, you may need
to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt
resistor which is connected between pins 2 and 3 of
a male XLR connector (DATA + and DATA -). This unit
is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using
a cable terminator will decrease the possibilities of
erratic behavior.
XLR Male Socket XLR Female Socket
2 Cold
2 Cold
3 Hot3 Hot
1 Ground
1 Ground
COMMON
DMX512 Out
3-PIN XLR
DMX512 In
3-PIN XLR
DMX +
DMX -
FIGURE 2
FIGURE 3
FIGURE 4
XLR Pin Conguration
Pin 1: Ground
Pin 2: Data Compliment (negative)
Pin 3: Data True (positive)
Termination reduces signal errors
and avoids signal transmission
problems and interference. It is
always advisable to connect a DMX
terminal, (Resistance 120 Ohm 1/4W)
between PIN 2 (DMX-) and PIN 3
(DMX +) of the last xture.

P. 4
Tecshow Quad Spider 60 |
4. MENU FUNCTION
Menu Button (from le to right) ”menu”, ”up”,
”down”, ”OK”
System Menu When making adjustments press
ENTER to conrm your setup then press and hold
the MENU button for at least 3 seconds. To exit
without making any adjustments press the MENU
button. The display will lock aer 30 seconds, press
the MENU button for 3 seconds to unlock.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN
buttons until “ADDR” is displayed, press ENTER.
2. The current address will now be displayed and
ashing. Press the UP or DOWN buttons to nd
your desired address. Press ENTER to set your
desired DMX address.
CHND - This will let select your desired DMX
channel mode.
1. Press the MENU button until “CHND” is
displayed, press ENTER. The current DMX
DMX Address
English version
Channel Modes
Master/Slave Mode
Show Mode
Auto Mode
Sound Mode
Sound Sense
Tilt 1 positive direction
or reverse direction
Tilt 2 positive direction
or reverse direction
Backlight
Display
Auto Test
Reset

P. 5
| Tecshow Quad Spider 60
channel mode will be displayed.
2. Press the UP or DOWN buttons to nd your
desired DMX channel and press ENTER con
conrm and exit.
SLND - This will let you set unit as a master or
slave in a master/slave conguration.
1. Press the MENU button until “SLND” is
displayed, press ENTER. Either “MAST”, “SL 1”,
or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your
desired setting is displayed, press ENTER to
conrm.
NOTE: In a Master/Slave conguration you can set
one xture to Master and then set the next xture to
“SL 2”, the xtures will now have contrast movement
to each other.
SHND - Show modes 0-15 (Factory programs).
Show mode can run with or without sound
active mode active.
1. Press the MENU button until “SHND” is
displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing
a number between 0-15. Shows 1-15 are factory
programs, while show “0” is random mode. Use
the UP or DOWN buttons to nd your desired
show.
3. When you have found your desired show press
ENTER, then press and hold the MENU button
for at least 3 seconds to activate. Aer you have
set your desired show, it can be changed at any
time using the UP or DOWN buttons.
AUTO- auto run mode.
1. Press the MENU button until “AUTO” is
displayed, press ENTER.
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is
displayed, press ENTER.
2. The display will show either “ON” or “OFF”.
Press the UP or DOWN buttons to select “ON”
to activate sound active mode, or “OFF” to
deactivate sound active mode.
3. Press ENTER to conrm.
SENS - In this mode you can adjust the sound
sensitivity.
1. Press the MENU button until “SENS” is
displayed, press ENTER.
2. A number between 0-100 will be displayed.
Press the UP or DOWN buttons to adjust the
sound sensitivity. 0 being the least sensitive,
and 100 being the most sensitive.
3. When you have found your desired setting press
ENTER to conrm.
PINT- With this function you can choose positive
direction or reverse direction of Tilt 1. This
option is used to reverse the Tilt 1 direction.
1. Press the MENU button until “PINT” is
displayed, press ENTER.
2. Press the “YES” or “NO” button to select
reverse or not reverse , choose “Yes” means
direction of Tilt1, choose “No” means negative
direction of Tilt1,
3. When you have found your desired setting press
ENTER to conrm.
TINT - With this function you can choose positive
direction or reverse direction of Tilt 2.
1. Press the MENU button until “TINT” is
displayed, press ENTER.
2. Press the “YES” or “NO” button to select
reverse or not reverse , choose “Yes” means
direction of Tilt2, choose “No” means negative
direction of Tilt2.
3. When you have found your desired setting press
ENTER to conrm
LED - With this function you can have the LED
display turn o aer 5 seconds.
1. Press the MENU button until “LED” is displayed,
press ENTER.
2. The display will show either “ON” or “OFF”.
Press the UP or DOWN buttons to select “ON” to
keep the LED display on at all times, or “OFF” to
English version

P. 6
Tecshow Quad Spider 60 |
switch to have the LED display switch o aer
10 seconds.
DISP - This function will reverse the display 180°.
1. Press the MENU button until “DISP” is
displayed, press ENTER.
2. Press the UP button to select “DSIP” to reverse
the display, or “DISP” to change the display
back.
3. Press ENTER to conrm. To make you LED
display reappear again press any button.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is
displayed, press ENTER. Positions.
RSET- This function will reset the program.
1. Press the MENU button until “RSET” is
displayed, press ENTER. positions.
5. DMX CHANNELS
10 channel denition table
Channel DMX Value Function
10-255 Tilt 1
20-255 Tilt 2
30-255 P/t Speed
40-255 Dimmer from 0-100%
5
Strobe
000-007 O
008-015 On
016-131 Strobe from slow to fast
132-139 On
140-181 Strobe Fast open slow close
182-189 On
190-231 Strobe Slow open fast close
232-239 On
240-247 Random strobe
248-255 On
60-255 Red Dimming
English version

P. 7
| Tecshow Quad Spider 60
14 channel denition table
Channel DMX Value Function
10-255 Tilt 1
20-255 Tilt 2
30-255 Tilt 1, Tilt 2 speed
40-255 Dimmer from 0-100%
5
Strobe
000-007 O
008-015 On
016-131 Strobe from slow to fast
132-139 On
140-181 Strobe Fast open slow close
182-189 On
190-231 Strobe Slow open fast close
232-239 On
240-247 Random strobe
248-255 On
60-255 Red 1 Dimming
70-255 Green 1 Dimming
80-255 Blue 1 Dimming
90-255 White 1 Dimming
10 0-255 Red 2 Dimming
11 0-255 Green 2 Dimming
12 0-255 Blue 2 Dimming
13 0-255 White 2 Dimming
70-255 Green Dimming
80-255 Blue Dimmin
90-255 White Dimming
10
Special Function
000-007 Only others channels can be controlled
008-063 Auto run
064-127 Sound active
128-255 Reset
English version

P. 8
Tecshow Quad Spider 60 |
Design and product specications are subject to change without prior notice.
14
Special Function
000-007 Only others channels can be controlled
008-063 Auto run
064-127 Sound active
128-255 Reset
English version

P. 9
| Tecshow Quad Spider 60
Versión Español
tecshow.amproweb.com
@amprogroup