AND-Tech AVR Prog MKII User manual

AVR Prog MKII
MANUAL
AVR Prog MKII manual
www.and-tech.eu 1

1. Programming in BASCOM and AVRDUDE 3
a) Driver in tallation 3
b) Configuration 7
1. BASCOM 7
2. AVRDUDE 9
2. Programming in AVR Studio 10
a) Driver in tallation 10
b) Configuration 11
3. Firmware update 13
4. Programmer interface 18
a) ISP connector 18
b) TPI and PDI connector 18
c) Jumper and LED 18
d) Bootloader button 19
5. Environment protection 20
ATTENTION!!
AVRISP mkII programmer i compatible with BASCOM and
AVR DUDE environment. If you want to u e thi programmer
with AVR Studio, you need to update it firmware (in truction in
chapter 3: Firmware update)
AVR Prog MKII manual
www.and-tech.eu 2

1. Programming in BASCOM
a) Driver in tallation
ATTENTION!!
Before you connect programmer to computer , in tall AVRJungoUSB driver fir t.
link: http://www.and-tech.pl/MKII/AVRJungoUSB.exe
To connect programmer to computer, mini U B cable is needed (widely used with mobile
devices and cameras). It is recommended to use 1.8m long cable or shorter.
To connect programmed circuit with programmer, IDC-10 cable is needed (pins order on
programmer).
After you connect programmer, system should find and install appropriate drivers. If I
nstallations is successful, device Jungo (with AVRI P mkII and WinDriver) should be
available in device manager.
ATTENTION!!
When programmer i in talled ucce fully, green LED diode hould turn on. If
not, connect programmer directly to PC or laptop without HUB or dock tation .
In ome ca e , programmer doe n't work properly with the e device .
AVR Prog MKII manual
www.and-tech.eu 3
Picture 1

Please download LibU bDotNet_Setup.2.2.8.
link: http://www.and-tech.pl/MKII/LibUsbDotNet_ etup.2.2.8.exe
After you accept licence agreement and chose installation path, you should see window presented in
Picture 2. Check only first position – Runtime Files and click Next.
Check Instalall libusb-win32 with filter capabilitied? as in Picture 3 and click Next.
AVR Prog MKII manual
www.and-tech.eu 4
Picture 3
Picture 2

tart Filter Wizard. It is available in the following path: tart >Programy >LibUsbDotNet >libUsb-
win32 >Filter Wizard.
AVR Prog MKII manual
www.and-tech.eu 5
Picture
Picture 4

In window Install/Remove Device Filter(s) choose first option: Install a device filter- Picture 6.
Now, please find device AVRI P mkII, as in Picture 7.
If installation is successful, the following window appears:
Programmer is installed correctly.
AVR Prog MKII manual
www.and-tech.eu 6
Picture 6
Picture 7
Picture 8

b) Configuration
1. BASCOM
ATTENTION!!
AVR Prog MKII i upported by BASCOM 2.0 and higher. If you work with older ver ion
plea e u e additional program AVRDUDE.
We need to configure programmer to make it work with BA COM environment. Please, start
BA COM and find programmer settings (Options >Programmer). Now find USBprog Programmer
/ AVRISP mkII in the following list (Picture 9).
Check U B and click OK.
AVR Prog MKII manual
www.and-tech.eu 7
Picture 9

Click Program chip icon in order to program circuit.
AVR Prog MKII manual
www.and-tech.eu 8
Picture 10
Picture 11

Flash, EEPROM, Lock and Fuse bookmarks show state of FLA H, EEPROM memory and fuse
bits after sending current program to processor.
Button:
- identifies processor
- checks if processor's memory is empty
- erases processor's memory and sends new program
AVR Prog MKII manual
www.and-tech.eu 9
Picture 12

2. AVRDUDE
In order to use AVRDUDE environment, please download avrdude-5.8-w32_avrdude-
GUI_1.0.5
link: http://www.and-tech.pl/MKII/avrdude-5.8.zip
After you extract it, turn on graphical user interface: avrdude-GUI.exe and then choose
from list Programmer: Atmel AVR ISP mkII (avrispmkII), from list Port: - usb and from
Device – choose model of processor, you want to program.
AVR Prog MKII manual
www.and-tech.eu 10
Picture 13