Andrew Alliance Waters OneLab User manual
INSTALLATION GUIDE
OneLab standalone server
Copyright © 2022 Waters Corporation
About this manual
Read the user manual before using this device. Strictly follow usage and mainte-
nance instructions provided in the manual. It is the user’s responsibility to become
familiar with all available information concerning the correct use, care and limita-
tions of these products. If you are uncertain about the correct use or limitations of
the products, contact Andrew Alliance service and support. The manufacturer, the
distributor and their respective owners, employees, agents and representatives are
not responsible or liable for errors or omissions.
Information in this User Manual is subject to change without notice and does not
represent a commitment on the part of Andrew Alliance. Andrew Alliance assumes
no responsibility for any inaccuracies that may be contained in this User Manual.
Andrew Alliance makes no commitment to update or keep current the information in
this User Manual, and reserves the right to make improvements to this User Manual
and/or to the products described in this User Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete, we
would appreciate your comments and suggestions.
Safety instructions
• The device must always be completely switched o (cables
removed) before moving it.
• The user must maintain a distance of at least 20cm from the
product (WiFi antenna) while it is being installed and operated.
• The device is intended for indoor use only.
• Device maintenance has to be done exclusively by an Andrew
Alliance representative.
• If the device is used in a manner not specied by the manufac-
turer, the protection provided by the device may be impaired.
Feel free to contact
the Andrew Alliance
support team Send us an email to
Chat with our support team
directly in OneLab
We reply within 1 business day
What’s in the package
Product overview
OneLab
standalone server
Power supply USB WiFi Adapter
(only for Service & Support use)
Gigabit Ethernet 2×
Power socket
Power button
with LED
If the server doesn’t start automatically,
please push the red power button on the
front face.
A. Installation of the standalone server
Unbox the standalone server.
Plug the standalone server into a power source.
You will know that the OneLab Standalone Server is ready
when you will see the “onelab_standalone” network
in the list of Wi-Fi networks.
The server should be
ready in less than a
minute.
1
2
3
onelab_standalone
!
B. Access to OneLab standalone
1
2
3
Connect your computer to OneLab standalone WiFi network
a. Go to your Wi-Fi settings
and select the network
named “onelab_standalone”
b. Enter network password
“OneLab_Standalone”
Launch a web browser, type http://192.168.5.1
and log into OneLab using these credentials
IMPORTANT!
Change the OneLab credentials
http://
192.168.5.1
Password: onelab
a. On OneLab, click on the menu located in the top right
b. Click on “Prole settings”,
go to “Account Password” area
and create a new password
Annex 1: Pairing your connected devices
with OneLab standalone
Press 5 times the main button Wait the LED sign to turn blue
and blink
After a couple of minutes, the de-
vice will inform you when it is in
installation mode.
5 times
Connect your computer, tablet or smartphone to your device
Launch a web browser, type http://192.168.2.1,
follow the on-screen steps to continue installation
and take the steps 5 and 6 in consideration (next page).
A. Go to your Wi-Fi settings and select the network named
Andrew-718.xxxx.xxxxx or Stand-618.xxxx.xxxxx
1 2
3
4
xxxx.xxxxx is the device serial number
(for Andrew+, you can nd it on the door of the Optical Location Module
and for Pipette+ Stand+, you can nd it in the back of your device)
B. The LED sign will stop blinking when it’s successfully connected.
http://192.168.2.1
In case you need to pair the device (e.g. switch from Wi-Fi to Ethernet):
In case of Wi-Fi connection,
select the onelab_standalone_xxxxxxxxx wireless network.
At this step, ll the form with these information
then continue the installation.
xxxxxxxxx is the MAC address of the Wi-Fi interface of the standalone server.
If wired connection will be used, simply follow the instructions stated
in the pairing application.
5
6
Network password: OneLab_Standalone
Password: onelab
OneLab web address: http://192.168.5.1
Annex 2: Power OFF the OneLab server
Never remove the server from the
power before switching it o.
Press the red button for 3 seconds
and wait until the LED will turn OFF.
Then, you may unplug the device
from the power source.
Technical data
SOC Intel 10th Generation Quad-Core J4125.
Its base operating frequency is up to 2.7GHz
Memory 8GB DDR4
Graphics Intel UHD Graphics to support 4K HD video playback
Storage capacity 256GB M.2 SSD
Video & audio • 2 × HDMI Port (4k @ 60Hz)
• 1 × Audio Jack (HP & MIC)
USB • 2 × USB2.0
• 2 × USB3.0
• 1 × Type-C port
Ethernet 2 × Gb Ethernet RJ-45
Wi-Fi 802.11 b / g / n / ac, Bluetooth 4.0
Operating system Linux
Power 12 V @ 2A
Operating humidity 30% ~ 90% relative humidity, non-condensing
Operating temperature 14-113°F / -10~45°C
Dimensions 124 mm × 113 mm × 41 mm (4.88 in × 4.45 in × 1.61 in)
Weight 0.2950 Kg
Certications CE/FCC Class A, RoHS compliant, REACH
Waters Corporation
34 Maple Street
Milford, MA 01757
USA
Phone: +1-508-478-2000
Andrew Alliance S.A. (HQ)
Chemin Grenet 21
1214 Vernier (Geneve)
Switzerland
Phone: +41 22 518 0357
Part number: 818.206.3 | 2022 © Andrew Alliance - A Waters Company.
Table of contents
