Anova RCPWC6 User manual

anovafurnishings.com
888.535.5005 tel
ASSEMBLY INSTRUCTIONS
RCPWC6 6  Flat Bench with Backrest
TOOLS NEEDED:
9/16” Open-end or Box-end Wrench•
Ratchet with 9/16” Socket•
18v (or more) Driver with No. 3 Phillips Head Bit•
2 x
3/8” x 1.25”
Hex Head Bolt
14 x
3/8”
Lock Washer
2 x
3/8” X 3.00”
Carriage Bolt
ASSEMBLY:
The assembly is a two-person operation.
ASI 291 Rev B HRD585 & HRD586 S587
Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.
ASSEMBLY HARDWARE:
BENCH COMPONENTS:
2 x
Bench Support
7 x
Seat/Backrest Plank
Seat End Cap
Seat Plank
2.25” long
Carriage Bolt
packaging cardboard
or other so surface
Flat Washer
Nut
Install Phillips Head
Screws into the front
two Planks and back
Plank only
2 x
Backrest Brace
12 x
3/8” X 2.25”
Carriage Bolt
18 x
3/8”
Flat Washer
Place four of the Seat Planks across the two3.
Bench Supports.
NOTE: When laying out the Planks, make sure the
face of the Planks with the pre-drilled pilot
holes faces downward.
Place a Seat End Cap over each end of the
Seat Planks, aligning the mounting holes with
the Plank mounting holes.
Install 2.25” long Carriage Bolts and insert the
Bolt through the End Cap, Plank and Bench
Support. Install Carriage Bolts through the
two front Planks and the back Plank. Install a
Flat Washer, Lock Washer, and Nut on each of
the Bolts. Tighten the hardware nger tight so
adjustments can be made later.
Bench
Support
1 x
Seat Support
2 x
Backrest End Cap
2 x
Seat End Cap
14 x
3/8-16
Nut
14 x
Phillips Head Screw
Tilt the Bench back so it rests on the tops of the Bench Supports.4.
Locate the two Backrest Braces and position each one about 2  from
the ends of the Bench. Use the Driver with Phillips Head Bit to drive
Phillips Head Screws through the Backrest Brace mounting holes and
into the pre-drilled pilot holes in the Seat Planks.
NOTE: Insert Screws into the two Front Planks and the Back Plank only.
Lock Washer
packaging cardboard
or other so surface
Flat Washer
Nut
Lock Washer
2.25” long
Carriage Bolt
Seat Plank
Bench Support
Seat End Cap
2 x
3/8-16
Flanged Nut
Locate the two Bench Supports and set them up about 6  apart on the packaging2.
cardboard or other so surface to avoid scratching the product.

Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to•
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,•
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.•
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: [phone]
web: anovafurnishings.com
11/2012
3” Long
Carriage Bolt
Flat Washer
Flanged Nut
Flat Washer
Flanged Nut
Seat Support
Phillips Head
Screws
Backrest End Cap
3” Long
Carriage Bolt
mounting hole
for Seat Support
mounting hole
for Seat Support
Carriage Bolt
Flat Washer
Lock Washer
Hex Nut
Phillips Head
Screws
3” Long
Carriage Bolt
Flat Washer
Flanged Nut
Seat Plank
Seat Support
Bench Support
Hex Head Bolt
Flat Washer
Flat Washer
Lock Washer
Hex Nut
Backrest End Cap
Locate the Seat Support and position it so that the ange with the mounting holes aligns with the mounting holes in the Bench5.
Support.
Install a 3.00” long Carriage Bolt through
the Seat Plank, Bench Support, and Seat
Support at each end of the Bench. Place a
Flat Washer and Flanged Nut on the end of
both Carriage Bolts and tighten nger tight.
Place a Flat Washer on one of the Hex Head Bolts and install the Bolt6.
through the mounting holes in one end of the Bench Support and the
Seat Support. Put a Flat Washer, Lock Washer, and Nut on the end and
tighten nger tight.
Install the remaining Hex Head Bolt with Flat Washers, Lock Washer,
and Nut through the mounting holes at the other end of the Bench.
Leave the Hex Head Bolt nger tight to allow for adjustments.
Use the Driver with Philips Head Bit to install Phillips Head Screws
through the Seat Support, Backrest Brace, and into the pre-drilled pilot
holes in the Seat Plank.
The remaining Seat Planks become Backrest Planks. Place7.
these three Planks across the upper portion of the Bench
Supports and Backrest Braces.
NOTE: When laying out the Planks, make sure the face of the
Planks with the pre-drilled pilot holes faces downward.
Place Backrest End Caps over the ends of the Planks and
secure them using 2.25” Carriage Bolts with Flat Washers,
Lock Washers, and Hex Nuts.
Turn the Bench upright and use the Driver with Phillips Head Bit8.
to install Phillips Head Screws through the Backrest Braces and
into the pre-drilled pilot holes in the Backrest Planks.
Tighten all the Carriage Bolt and Hex Head Bolt hardware sets.9.
Move the assembled Bench to the desired location.10.
Retighten hardware two weeks aer initial assembly.11.