Antonio Bernini REVOTECH GT User manual

A perfect amalgamation of passion and performance, enduring emotions
with automotive engineering, Antonio Bernini presents yet another wrist
adornment- Revotech GT from its Racing Series.
Sporty, elegant & racy, the Revotech GT embodies the automotive excellence
and is a must have for every race enthusiast.
Revotech GT, simulates the GT experience in the dial with oversized numerals
for optimal legibility during racing with extra large spring supported chrono
pushers with an extended crown for ease of functioning.
REVOTECH GT

Chronograph
Second Hand
Minute
Hand
Button A
Chronograph
Start/Stop
Button B
Chronograph
Lap Time
Measurement/Reset
Date
Feature
Hour
Hand
Chronograph
Minute Hand
Day
Feature
Crown
Normal
Second Hand
DISPLAYS AND BUTTONS

•Pull the crown out to the 2nd Position to stop the watch movement. An indicator of this
would be that the Second Hand stops functioning.
•Turn the crown clockwise or anti-clockwise to set the hour and minutes.
•Push the crown back to Normal Position and ensure it is pushed in.
SETTING THE TIME
Normal
Second
Hand Minute
Hand
Hour
Hand
Crown’s
2nd Position

•Pull the crown out to the 2nd Position.
•Turn the crown clockwise for a full round of 24 hours to change the day.
•Push the crown back to Normal Position and ensure it is pushed in.
SETTING THE DAY
Normal
Second
Hand Minute
Hand
Hour
Hand
Crown’s
2nd Position
Day
Feature

SETTING THE DATE
•Pull the crown out to the 1st Position.
•Turn the crown clockwise to set the date.
•Push the crown back to Normal Position and ensure it is screwed in.
* Never Correct the date between 9:00PM and 12:30 AM
Normal
Second
Hand Minute
Hand
Hour
Hand
Crown’s
1st Position
Date
Feature

CHRONOGRAPH FUNCTIONALITY
Simple Time Measurement
•Press Button ‘A’ to start measuring the time using the Chronograph.
•Press Button ‘A’ again to stop the Chronograph Second Hand and measure the elapsed
time.
•On Pressing Button ‘A’ again, you can continue measuring the time from where it was
stopped.
•You can continue the above steps to measure and read multiple simple time(s).
•Press Button ‘B’ to reset the chronograph.
Chronograph
Minute Hand
Chronograph
Second Hand
Button A
Chronograph
Start/Stop
Button B
Chronograph
Lap Time
Measurement/Reset

•Press Button ‘A’ to start measuring the time using the Chronograph.
•Press Button ‘B’ to measure a lap (the Chronograph Second Hand will stop but the
chronograph movement will continue)
•On Pressing Button ‘B’ again, the Chronograph Second Hand will move forward to catch
up with the actual time elapsed.
•You can continue the above steps to measure and read multiple intermediate time(s).
•To Reset, first Press Button ‘A’ to stop the Chronograph and then Press Button ‘B’.
CHRONOGRAPH FUNCTIONALITY
Lap Time or Intermediate Time Measurement
Chronograph
Minute Hand
Chronograph
Second Hand
Button A
Chronograph
Start/Stop
Button B
Chronograph
Lap Time
Measurement/Reset

Cleaning
Ensure the watch is cleaned from time-to-time. Use a cloth to dab the
glass to remove the dust. Wipe the belt with a wet cloth (not the leather
belt).
Condensation
Sometimes a slight condensation may appear under the glass of your
watch. This mist will disappear on its own and will not affect the
functioning of your watch.
Do not leave your timepiece anywhere where it might be subjected to
major variations in temperature or humidity, in direct sunlight or near
strong magnetic fields.
Water Resistance
Ensure the crown is pushed back and is screwed in correctly before the
watch is taken under water.
CARE AND MAINTENANCE

An Antonio Bernini Timepiece operates for more than 2 years in continuous use.
If you envisage not wearing your chronograph for several weeks or months, we would
advise you to put it to one side with the crown pulled out, extending battery life
considerably.
We would advise you to have your watch inspected every 2 –3 years, to benefit from
the highest standards of service and to ensure your guarantee remains in force.