APLOS ANGEL 600 GPD User manual

Instruction Manual
Manufactured for EPS Group
aplos.ie
Direct Flow
Reverse Osmosis
Drinking Water System
600 GPD

Precautions
01
Introduction
Aplos Angel 600GPD is one of the newest drinking water purifiers, with a
compact, slim design, 4 stage filtration, large capacity, direct flow (i.e., no
storage tank) system, that produces minimum amount of wastewater. Color
indicators embedded in the operation panel help monitor the remaining filter
lifespan, warning when replacement is required.
The system utilizes advanced reverse osmosis technology to purify water.
It relies on the artificial reversal of the naturally occurring osmosis process.
The reverse osmosis membrane with a pore size of 0.0001 micron (0.1 nm),
can significantly improve the quality of your tap water by effectively reducing
bacteria, viruses, heavy metals, pesticide residue, lead, fluoride, and other
harmful substances. Produced water is fresh, pure, and suitable for direct use.
Please read through the instructions carefully before using or installing the
product.
◆ The system must be properly installed and serviced in accordance with the
manual.
◆ We recommend that the system is installed by a trained professional.
◆ The reverse osmosis system should be installed vertically, do not lay down
on it's side.
◆ Reverse osmosis system must be connected to the cold water supply only
◆ Install a pressure reducing valve for inlet water pressure above 3 bar
◆ After reverse osmosis installation, drain water from the RO tap for at least
10 mins. Repeat at least 3 times over the next 24 hours.
◆ It takes a few seconds for water to emerge after the "purified water" tap is
open. If your water supply has a lot of air, you will see bubbles. They float to
the top and dissipate after a few seconds. This is expected and it does not
af fect purified water quality .
◆ If RO system has not been used for more than 72 hours, press the flush
button on the operation panel. Let at least 500 ml of water drain if it smells
or tastes bad.
◆ Do not put magnetic objects close to the water tap, as that may cause an
abnormal startup of the machine and create a potential safety hazard.
◆ Do not install the system where it will be exposed to direct sunlight or
harmful chemicals, or any place where it may be damaged.
◆ Do not install the system near any heat source.
◆ Do not install the system outdoors.
◆ Do not use the system with water that is microbiologically unsafe or of
unknown quality without adequate disinfection.
◆ If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
◆ This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
◆ Shut of f water supply to the unit and unplug if RO system if it will not be in
use for more than a week. Upon return, reactivate water supply and power.
Let purified water drain for at least 5 minutes before usage.

02
Product description
Frame
S/N
Name
Power port
Flush button
Reset button
CFIII life indicator
S/N
6
7
8
9
10
S/N
Back housing
RO Purified water port
Inlet water port
Drain port
RO membrane life indicator
5
2
3
4
1
Water Purification Process Flowchart
S/N
Name Name
Name
3
4
5
6
2
19108
11
7
2
1
34
5
6
78
CFIII composite filter
1
2
3
4
5
6
7
8
Booster pump
RO filter
Wastewater solenoid valve
Check valve
High-pressure switch
Tap
Inlet solenoid valve

Parts and materials in contact with water
Part name Material Quantity Service life
RO membrane filter PP filter housing, PA
Composite filter element
made of PP cotton,
phosphate, and activated
carbon rods
1
6-12months
PP filter housing, PP carbon
Phosphate particles, activated
carbon rods
Model specifications
2-3years
1
03
Specifications
Operating pump pressure
Filtration stages
Rated voltage
Brand
Model
Inlet pressure
Rated power
Operating temperature conditions
Inlet water temperature
Feed water requirements
(Recovery, %)
Product name
Purified water production rate
Electric Control Schematic Diagram
1199480
1199479
* The service life of the filters are estimated based on the average daily pure water consum ption o f 20L in ordinary households and the inlet water
meets the following conditions: water temperature 5°C-38°C, inlet pressure 1-4 bar, pH 7.5+/-0.5, turbid ity <1. 0NTU, total dissolved solids (TDS)
≤500mg/L, total organic carbon (TOC) ≤1.0mg/L
* Filters should be replaced timely according to indicators to ensure high qualit y of purified water. The service life of the filter varies depending on
the inlet water quality and temperature, inlet pressure, daily usage of purified water, an d operating environment.
Inlet solenoid
valve
High- pressure
switch
Booster pump
Flush solenoid
valve
Power adapter CPU
Main con trol board
Red
Green
Red
Green
APLOS
Angel 600 GPD
4
60W
220V～
Municipal tap water or pre-treated well water
65%
Direct flow reverse osmosis drinking
1-3 bar
4-6 bar
90L/h
5°C-38°C
4°C-40°C
Maximum daily production rate 600 GPD

04
Display signal description
Filter Replacement
1. Shut off water supply to unit.
2. Open tap to drain pure water and release pressure. Close tap.
3. Isolate power and unplug unit.
4. Slightly bend the unit backward. Hold the bottom of the filter that is being replaced
and pull it out.The filter will rotate and come off.
5. Align the new filter with the corresponding tube inside the unit.
Press down firmly on the bottom of the filter until you hear a "click" sound,
indicating that it is properly installed.
6. Reactivate water supply and power
7. Check for any water leakage
8. Reset replaced filter lifespan (refer to the procedure described above, steps
3.1-3.3)
9. Press "Flush" button to flush the system`s filters
1. Filter life indicators
Filter life power indicators (red, yellow, green) display in real time and their color
reflects the corresponding filter lifespan.
1.1 Green indicates that the life of the filter is normal.
1.2 Yellow indicates that the life of the filter is about
to expire.
1.3 Red indicates that the filter life has expired and
needs to be replaced urgently. The system will
beep 5 times every 3 hours, until filter is replaced
and reset.
2. Flush button:
Press "Flush" to turn the rinsing function on and of f.
3. Reset button:
3.1. Press "Reset" to enter the reset mode: the RO
filter life indicator stays on and the other goes of f , indicating that the RO filter is
selected. Press "Reset" again to switch to the CFIII filter life indicator.
3.2 If there is no operation within 5 seconds, it will exit the "Reset" mode and return
to the regular operating state.
3.3 Hold "Reset" for 3 seconds to reset the life of the selected filter to its original life.
After reset, it will enter the regular operating state, and the filter life indicator will
turn green.

05
Before installation, please check that all components are included in the package.
Installation Step
I. Install the three-way ball valve (see Figure 1)
1.1 Take out the three-way ball valve from the
accessory box.
1.2 Close the water inlet valve.
1.3 Connect the water inlet three-way valve and the
ball valve (note that the threaded connection
should be sealed with padding material and
seal ring).
1.4 Reconnect the original water pipe.
1.5 Connect the PE pipe to the water outlet of the
three-way ball valve and reserve a certain
length of the PE pipe.
II. Install the tap (see Figure 2)
2.1 Confirm the installation location for the RO
tap and drill a hole.
2.2 Fix the tap in the installation position. Ensure
that the tap base does not rotate, the platform
and the water pipe connections do not leak.
2.3Connect the quick fitting with a PE pipe first,
then connect the other end of the quick fitting
to the tap, leaving suf ficient length for the
pipe .
III. Install the drain saddle (see Figure 3)
3.1 Install the drain saddle on the vertical drainpipe,
which is the recommended location.
3.2 Place the saddle on the drainpipe and align for
drilling.
3.3 Drill a hole in the drainpipe carefully. Be sure
not to penetrate the opposite side of the pipe.
Slip the front plate on one end of the tubing and
insert the tubing into the drilled hole for about
0.6''. Position the back plate on the drain pipe
by tightening the screws and nuts evenly while
leaving the tubing in the hole
IV. Connect pipes and power supply
4.1 Connect the pipe from the three-way ball valve
to the inlet water port and the pipe should be
connected securely to avoid leakage.
4.2 Connect the PE pipes from the tap to the RO
purified water and filtered water ports
4.3 Connect the drain water pipe to the drain port.
Do not install any valve on the drain water pipe.
4.4 Activate power supply. First, connect the power
adapter to the unit power port, and then plug it
into the socket
V. Start up and Inspection
5.1 Open the RO tap and the water inlet ball valve.
RO system will start working, automatically
flushing, and water will be discharged from the
drain pipe. After approximately 10 seconds, the
flushing will end, and the RO system ill be ready
to purify water. Water will flow through the filters
directly to the tap.
5.2 Stop the unit for inspection. Turn of f the tap.
The drain pipe will stop draining water, but the
system will continue operating until it is full of
purified water.
5.3 Pipeline inspection. During the trial operation,
check the parts, components, and connections
for leakage and looseness.
5.4 After installation and inspection drain water
from the RO tap for at least 10 min. Repeat at
least 3 times over the next 24 hours.
Figure 1
Figure 2
Figure 4
Figure 3

Repair Guide
Failure description Possible Cause Troubleshooting
Purified water
isn't coming
through the
system
Water leaks at
the connection
Purified water has
an unpleasant
taste or smell
Wastewater pipe
does not drain
Damaged connector
seal ring
Damaged filter cartridge
seal ring
The water purifier has not
been used for a long time
The water purifier was not
flushed as required when
it was installed Incorrect
tubing installation.
Inlet valve is not open
CF Composite filter or
RO membrane blockage
Unit is not powered
Inlet valve is not open
Filter blockage
Flush solenoid valve
blockage
Wastewater pipe
keeps draining
Water purifier
cannot be stopped
Severe RO membrane
blockage
Failure of high-pressure
switchFailure of inlet
solenoid valve
Failure of one-way valve
Failure of inlet solenoid valve
Water purifier
starts frequently
Loud sound of
RO system
Reversed installation of
check valve
Check valve missing
Failure of check valve
Water pressure is lower
than 1.5 bar
The system is placed
against the cabinet.
Internal water pipe
interference
Composite filter blockage
Ensure proper installation of the check valve
Increase water inlet pressure. The sound will
decrease when the water pressure stabilizes
Do not place the system against the cabinet.
The system may vibrate when in operation
Adjust internal pipeline Replace the filter
Open the water inlet valve
Replace the filter
Check the power under the sink, as this
mostly occurs when the power under the
sink is off. Also, check the connection
between the plug and the power outlet,
and ensure that the system has been
plugged correctly into the power outlet
Contact the seller for the replacement
spare parts
Drain at least 500 ml of water before
purified water usage
Re-Flush as required
Make sure the waste water tubing is not
connected with RO tap
Contact the seller for the replacement spare
parts
Replace the filter
Contact the seller for the replacement spare
parts
06
Open the water inlet valve
Replace filter. If well water as the source
and the feed water has not been pre-treated,
the filter get clogged quickly. Ensure that
the feed water is pre-treated. Otherwise,
large particles in the well water will easily
clog the filter and shorten the filter life.
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the environ
ment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact the retailer
where the product was purchased.
They can take this product for environmental safe recycling.
Correct Disposal of this product

Packing List
Name
PE tube (1/4")
Unit
set
PE tube (3/8")
RO System
Quantity
1
1
1
package
RO tap 1
pc
User Manual
set
Accessories
Power adapter pc
set
1
set 1
1
Name
Unit
Quantity
Product warranty period is 12 months from the date of purchase.
Warranty only applies if the system is installed, used and maintained in compliance
with instructions and requirements enclosed with this system.
The warranty does not cover:
• components that require replacement because of normal wear and tear;
• faults and problems that have arisen due to untimely replacement of consumables.
All claims related to taste, smell, and other quality indicators of water purified by
this system should be accompanied with a water test report issued by an accredited
laboratory.
Warranty
After-sales Service Record
Service
date
Cause of service Service description
Service
personnel
signature
User
signature Remarks
aplos.ie