Applico CL64SS User manual

1
User Manual for your
CL64SS/W
CL66SS
4 burner gas hob
CL75SS
CL90SS
5 burner gas hob
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
GS 21/12/10

2
Contents
Environmental note 3
Important safety information 4 – 6
Specifications 7 – 12
CL64SS/W 7
CL66SS 8
CL75SS 9
CL90SS 10
Electricaldetails 11
Gasdetails 11
Gas hob surface layouts 11 - 12
Using the gas hob 13 - 15
Beforefirstuse 13
Switchingthehobon 13
Automaticignition 13-14
(CL64SS/W)
Automatic ignition with flame failure safety device 14
(CL66SS / CL75SS / CL90SS)
Energysavingtips 14-15
Cleaning 15 - 16
Cleaning the hob top 15
Aftereachuse 15-16
Cleaning the hob burners 16
Maintaining the cast iron pan stands 16
(CL66SS / CL75SS / CL90SS)
Installation 17 - 27
Positioning 17
Unpacking the appliance 17 - 18
Installing the appliance 18 – 21
Gas connection 21
Ventilationrequirements 21-22
Gas Safety (Installation and Use) Regulations 22 - 23
Gas Adjustment (Conversion to LPG) 23 - 24
Minimum flow adjustment for hob gas taps 24 - 25
Gas tap maintenance 25 - 26
Electricalconnection 26
Replacing the mains supply cable 26 - 27
My appliance isn’t working correctly 27
Warranty card 31 - 32

Environmental note
3
oThe packaging materials that we use are environmentally
friendly and can be recycled.
all packaging material with due regard for the
environment.
oPlease discard

4
Important safety information
Your safety is of the utmost importance to us. Please
make sure that you read this instruction booklet before
attempting to install or use the appliance. If you are
unsure of any of the information contained in this
booklet, please contact the Retailer where you
urchased your unit from.
ehold use and for
ambient temperature of the
scolouration at
of this temperature limit, will be the liability of
uarantee. The foregoing does not affect
f the manufacturer
ld not use this appliance to store items on or as a work
kept away
p
General Information
This appliance is designed for domestic housothe cooking and frying of domestic foodstuffs.
oIMPORTANT: The adjacent furniture and all materials used in
the installation must be able to withstand a minimum
temperature of 85°C above the
room it is located in, whilst in use.
oCertain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage or di
temperatures below the guidelines given above.
oAny damage caused by the appliance being installed in
contravention
the owner.
oYour new appliance is guaranteed against electrical or
mechanical defects, subject to certain exclusions that are noted
in the Conditions Of G
your statutory rights.
oThe use of this appliance for any other purpose or in any other
environment without the express agreement o
will invalidate any warranty or liability claim.
oYou shou
surface.
oNo modifications to the appliance are permitted by us.
oYou should not store or place flammable or highly flammable
liquids/materials on top of or near the appliance. Items made
from aluminium, plastic or plastic film should also be
from the appliance, as they may fuse to the surface.

5
oRepairs may only be carried out by an Authorised Service
Log onto www.applico.co.nzAgent. to locate a Service
Agent nearest to you.
end that babies and young children are
prevented from being near to the appliance and not allowed to
oIf it is necessary for younger family members to be in the
en should only be allowed to utilise the appliance
when supervised.
oCare should be taken to ensure that the units and work surfaces
u build the appliance into, meet with the relevant
standards.
use.
oYou should not allow the electrical connection cables to come
oIf fat and oil overheats, then it can ignite extremely quickly. For
e left unattended.
oMake sure that all of the cooking zones are switched off after
use.
Child Safety
oWe strongly recomm
touch the appliance at any time. During and after use, all
surfaces will be hot.
kitchen, please ensure that they are kept under close supervision
at all times.
oOlder childr
General Safety
oThe appliance should only be installed and connected by an
Authorised Service Agent.
that yo
During use
oAny film or stickers that are present on the hob surface when it
is delivered should be removed before
oCare should be used when utilising the appliance, otherwise
there is a risk of burns being caused.
into contact with the hob surface when it is hot or any hot
cookware.
this reason, when cooking with fat and oil the appliance should
not b

6
Cleaning
ular basis.
ains and cool.
uld not use a steam jet or any other high pressure
quipment to clean the appliance.
cordance
ith the manufacturer’s instructions and the
oThe manufacturer declines any responsibility for injury or
fN 721 MUST be followed.
nd that this appliance is installed on
any type of marine vessel.
Declaration of conformity
Th
of
EC.
9/109/EEC dated 25/01/1992 Materials that can touch food.
b is built using certified
aterials and requires the appliance to be installed in accordance with
e standards currently in force. This appliance must be used by a
omestic purposes only.
oCleaning of the hob should be carried out on a reg
oIMPORTANT: Before attempting to clean the appliance, it
should be disconnected from the m
oGreat care should be taken whilst using this appliance and when
following the cleaning procedure.
oYou sho
cleaning e
Installation
This appliance must be correctly installed by an
Authorised Service Agent, strictly in ac
w
relevant Standards. Please see the specific section
of this booklet that refers to installation.
damage, to person or property, as a result of improper
use or installation of this appliance.
oIf the appliance is being used in a Leisure Accommodation
Vehicle, the requirements o
oWe DO NOT recomme
is appliance complies with the following European Directives:
-73/23/EEC dated 19/02/1973 Low Voltage Directive.
-89/336/EEC dated 03/05/1989 EMC Directive inclusive
Amending Directive 92/31/E
-93/68/EEC dated 22/07/1993 CE Marking Directive.
-8
-90/396/EEC Gas Products.
-EN60335-1, EN60335-2, EN301-1 Safety Standards.
The manufacturer declares that the ho
m
th
trained person for d

7
pecificationsS
CL64SS/W
Product dimensions: Aperture dimensions:
Depth: 480 mm
550 mm
r
burner
urner
ion
s
tandard accessories:
oLPG conversion jets
Depth: 510 mm
Width: 595 mm Width:
Height: 30 mm
Product specifications:
o1 x 3.30 kW rapid burne
o2 x 1.75 kW semi-rapid
o1 x 1.00 kW auxiliary b
oFront control operat
oAutomatic ignition
oEnamelled pan stand
S

CL66SS
Product dimensions: Aperture dimensions:
8
Depth: 480 mm
idth: 595 mm Width: 550 mm
2 x 1.75 kW semi-rapid burner
rner
oHeavy duty cast iron pan stands
ty device
oLPG conversion jets
Depth: 510 mm
W
Height: 30 mm
Product specifications:
o1 x 3.60 kW rapid burner
o
o1 x 1.00 kW auxiliary bu
oFront control operation
oAutomatic ignition
oFlame failure safe
Standard accessories:

CL75SS
Product dimensions: Aperture dimensions:
9
Depth: 480 mm
idth: 740 mm Width: 550 mm
rner
2 x 1.75 kW semi-rapid burner
rner
oHeavy duty cast iron pan stands
ty device
oLPG conversion jets
oWok stand
Depth: 500 mm
W
Height: 30 mm
Product specifications:
o1 x 4.20 kW triple crown wok bu
o1 x 3.30 rapid burner
o
o1 x 1.00 kW auxiliary bu
oFront control operation
oAutomatic ignition
oFlame failure safe
Standard accessories:

CL90SS
Product dimensions: Aperture dimensions:
10
Depth: 480 mm
idth: 860 mm Width: 830 mm
rner
2 x 1.75 kW semi-rapid burner
rner
oHeavy duty cast iron pan stands
ty device
oLPG conversion jets
Depth: 510 mm
W
Height: 40 mm
Product specifications:
o1 x 4.20 kW triple crown wok bu
o1 x 3.30 rapid burner
o
o1 x 1.00 kW auxiliary bu
oFront control operation
oAutomatic ignition
oFlame failure safe
Standard accessories:

Electrical details
11
Rated Voltage: le pole switched fused outlet with
ax Rated Inputs: 0.02 kW
y Lead: 3 core x 0.75mm² (Type RR-F <HAR> marked)
l Gas (20.9 mbar)
ur hob is located on
e underneath of the appliance. Therefore it is a good idea to record
pliance.
ate of Purchase ……………………………….
face layout
r
d
burner
D) Control
panel
230 Vac 50 Hz
Supply Connection: 13 A (doub
3mm contact gap)
M
Mains Suppl
Gas details
Connection: Rp ½ (ISO R7)
Type: Natura
Alternative LPG G30 (28-30 mbar)
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of yo
th
this information before you install your ap
Model Number ……………………………….
Serial Number ……………………………….
D
Gas hob sur
CL64SS/W
A) 3.30 kW
rapid burne
B) 1.75 kW
semi-rapi
burner
C) 1.00 kW
auxiliary

12
L66SS
A) 3.60 kW triple
crown wok
burner
B) 1.75 kW semi-
rapid burner
C) 1.00 kW auxiliary
burner
D) Control panel
L75S
A) 4.20 kW triple crown wok burner
B) 3.30 kW rapid burner
C) 1.75 kW semi-rapid burner
D) 1.00 kW auxiliary burner
E) Control panel
C
S / CL90SS C

13
sing the gas hobU
Before first use
IMPORTANT: You should clean the hob surface (see
and maintenance” section).
Switching the ho
The following symbols will appear on the control panel, next to each
l
“Cleaning
b on
knob:contro
= gas off
Large flame: maximum setting
Small flame: minimum setting
The miniomum setting is at the end of the anti-clockwise
od between the maximum
a knob position between the maximum and off
ond
on
oburner is lit, turn the control knob to your required
ourner off, turn the control knob fully clockwise to
the gas off position.
rotation of the control knob.
All operation positions must be selecte
and minimum position.
oNever select
position.
oThe symbol on the control panel, next to the control knob will
indicate which gas burner it operates.
Automatic ignition (CL64SS/W)
To ignite a burner:
Press in the control knob of the burner that you wish to light a
turn it anti-clockwise to the maximum position.
If you keep the control knob depressed, the automatic ignitio
for the burner will operate.
Once the
setting between the maximum and minimum setting symbols.
To switch the b

oIn case of power failure, the burners can be lit by carefully using
a match.
14
utomatic ignition with flame failure safety device (CL66SS /
e burner head in
e event of the flame going out.
aximum position.
oYou should hold down the control knob for 20 seconds after the
etting between the maximum and minimum setting
symbols.
oTo switch the burner off, turn the control knob fully clockwise to
the gas off p
oIn case of power ilure, s y carefully using
a match.
Energy saving ti
PANS
A
CL75SS / CL90SS)
The appliance is fitted with a flame failure safety device on each
burner, which is designed to stop the flow of gas to th
th
To ignite a burner:
oPress in the control knob of the burner that you wish to light and
turn it anti-clockwise to the m
oIf you keep the control knob depressed, the automatic ignition
for the burner will operate.
flame on the burner has lit.
oAfter this 20 second interval, turn the control knob to your
required s
osition.
fa the burner can be lit b
ps
BURNERS
Minimum
ØØ
Maximum
Rapid 180 mm 220 mm
Semi-rapid 120 mm 200 mm
Auxiliary 80 mm 160 mm
oThe diameter of the bottom of the pan should correspond to that
of the burner.

15
oThe burner flame must never extend beyond the diametre of the
oUse flat bottomed pans only
little water as possible, to reduce
cooking times.
IMPORTANT: Always place pans centrally over the hob burners and
m
r hob burner flam
pan.
oWhen possible, keep a lid on the pan whilst cooking.
oCook vegetables with as
so that the handles cannot get accidentally caught or
You should also make sure that the handle is not over one
es.
position the
knocked off.
of the othe
Cleaning
Cleaning operations must only be carried out when
cool.
n
ny residues that are left on the hob top surface from cleaning
agents will damage it. You should remove any residues with
ace;
ater.
Although it is easier to clean some deposits whilst the
soft,
oth
be wrung out after being taken out of the soapy water.
bing the surface with a soft, clean cloth.
the hob is
The appliance should be disconnected from your
mains supply before commencing any cleaning
process.
ing the hob top Clea
A
warm soapy water.
Abrasive cleaners or sharp objects will damage the hob surf
you should clean it using warm soapy w
hob surface is still warm. Make sure that the hob surface,
pan supports and hob burners have all cooled sufficiently
before you attempt to touch them.
After each use
oRemove the pan stands and wipe the appliance over with a
damp cloth that has been put into warm soapy water. The cl
should
oDry the appliance by rub

16
oWe would recommend that an appropriate neutral and non-
The hob burners should be cleaned once a week or more frequently if
hob burners have cooled before you attempt to touch them.
pulling them upwards and away
from the hob top.
r about ten minutes in hot water and a little
detergent.
oBefore placing the burners back on the hob top, make sure that
oIMPORTANT: Make sure that you reassemble the burners in the
s (CL66SS / CL75SS /
L90SS)
IMPORTANT: Make sure that the hob surface and pan stands
has been
put into warm soapy water. The cloth should be wrung out after
being taken out of the soapy water.
oUsing a paper towel, thoroughly dry the pan stands.
oTo maintain the appearance of the cast iron pan stands, we
would recommend that you rub a small amount of olive oil into
the pan stands, after you have finished cleaning them.
flammable detergent is used to clean the glass surface of the
hob.
Cleaning the hob burners
they get soiled.
oIMPORTANT: Make sure that the hob surface, pan stands and
oRemove the hob burners by
oSoak them fo
oAfter cleaning and washing them, wipe and dry them carefully.
the gas jet is not blocked.
original way.
Maintaining the cast iron pan stand
C
ohave cooled before you attempt to touch them.
oWipe the pan stands over with a soft, damp cloth that

Installation
The installation must be carried out by an
oAS/NZS 3000:2007 Wiring Regulations
a bathroom or shower room.
etween the highest point of the hob surface (including
iding that the underside
e with the outer edge of the hob.
horizontal surface is lower than 400 mm,
of the
nce, measured from the cut out and between the hob
liance
ng the appliance please check that the following items
Authorised Service Agent, in accordance with the
current version of the following.
o2010 Electricity Safety Regulations
Positioning
The adjacent furniture must be able to withstand a
minimum temperature rise of 85°C above the ambient
temperature of the room it is located in, during
periods of use.
oThis appliance can be located in a kitchen, a kitchen diner or a
bed sitting room. IMPORTANT: The appliance must not be
installed in
This appliance is classified as Class 3 and therefore is to be built into a
kitchen unit (depending on size) or 600mm worktop, providing the
following minimum distances are allowed:
o700 mm b
the burners) and the underside of any horizontal surface directly
above it.
o400 mm between the hob surface, prov
of the horizontal surface is in lin
If the underside of the
then it must be at least 50 mm away from the outer edges of
the hob.
o50 mm clearance around the front, back and sides
applia
surface and any combustible materials.
Unpacking the app
When unpacki
are contained within the packaging:
1 x Hob
Pan stands
Burner assemblies
Instruction manual
Warranty card
17

18
ixing screws
ealing strip
F
Clamps
S
LPG conversion jets
Self-adhesive label for amending the gas category on the appliance’s
rating plate (required if the LPG conversion jets are used).
Installing the appliance
CL64SS/W
CL66SS

19
CL75SS
L90SS
le in the worktop that corresponds with the illustration
above.
the underneath of the appliance and any surface that is below it.
C
oCut a ho
oIMPORTANT: You must have a gap of at least 25 mm between

oCarefully turn the hob upside down and place it on a cushioned
mat.
oApply the sealing strip (A) provided around the edge of the
appliance.
oThe protective covering must be removed from both sides.
oDo not leave a gap in the sealing agent or overlap the thickness.
oIMPORTANT: Do not use a silicon sealant to seal the appliance
against the aperture. This will make it difficult to remove the hob
from the aperture in future if it needs to be serviced.
(A) Sealing strip
(B) Clamp
(C) Screw
oPlace the clamp (B) over the holes that match the size of the
screws. There are one set of screw holes in each corner of the
hob. Slightly tighten a screw (C) through the clamp (B) so that
the clamp is attached to the hob, but so that you can still adjust
the position of it.
oCarefully turn the hob back over and then gently lower it into the
aperture hole that you have cut out.
20