APPLIED ELECTRONICS ERGOADVANTAGE 7823H Series User manual

Avia Pole-mount Monitor Arm
Assembly Instructions
Page 1 of 3
D
A
C
M
m
B
F
1. Mount pole (F) to work surface usingeither the clamp
or grommet (see sidebar).
2. Assemble supportring(D). to pole at desired height.
3. Mount arm assembly (E) or dual hub with arms (m)
to pole (set tocorrect height) and tighten set screw (G)
to forcorrect tension, followedby trimring (A).
4. For additional screens, repeat steps 2to 5.
5. Insert monitor cables through cable managers (M)
and support ring tabs (D).
6. Mount monitor onto knuckle (C).
7823H & 7818H Series
C
C
M
B
q
F
n
A
Dual Hub Models
1. Mount pole (F) to work surfaceusing either theclamp
or grommet (see sidebar).
2. Assemble support ring (q).to pole atdesiredheight.
3. Mount Dual Hubassembly (n) to pole (set tocorrect
height) making sure the front plate slides between
the cable managers on the support ring (q) followed
by trimring (A).
4. Tighten setscrews at rear of hub.
5. For optional thirdscreen,assemble support ring (D)
to pole at desired height. Mount monitor assembly (C)
to pole (set tocorrectheight) followed by trimring (A).
6. For additional screens, repeat steps 2 to 5.*
7. Insert monitor cables through cable managers (M)
and support ringtabs (D) and/or dual hubsupport ring (q).
8. Mount monitor ontoknuckle (C).
*20 lb. maximum screen weight per monitor mount.
Your arm style
may vary from
illustration.

Avia Pole-mount Monitor Arm Assembly Instructions
Page 2 of 3
Mounting pole to work surface using
the Grommet Mounting System:
1. Use Phillips screw driver to remove the screws which
attach the upperclamp bracket (J) to polebase.
2. Assemble lower clamp bracket(H) to furthest slots
on upper clamp bracket (J) to alignclearance holes.
3. Slideknob (j) on to bolt (K) (long 3/8” bolt).
4. Lay monitor cables through grommet holes inthe work surface.
5. Alignpoleonwork surface.
6. Installbolt(K) through the clearance holes on clamp bracket(J)
insert the threaded end through the grommetand into the pole
base, using knob (j) to tighten securely.
7. For applications requiring increased tightness, remove knob
frombolthead and using a 9/16”wrench tighten the bolt
to 90 in-lbs. Caution: DO NOT OVERTIGHTEN
Adjusting the Height Adjustable Segment:
1. Removethe plastic shroudonthe side of the height
adjustable segment.
2. With the monitor mounted to the arm, move the monitor through
the heightrange; Ensure the arm will hold the monitor in the
positionyou placed it.
3. If the monitor drops or rebounds upward,adjust the tension screws at the front
and back of the arm segment as shown using the 3/16” Allen key. Repeatsteps
until the monitor is counterbalanced.
Mounting pole to work surface using the Clamp Mounting System:
1. Slideknob (j) on to bolt (l) (short3/8”bolt),ensuring the bolthead is
securely engaged into the knob.
2. Screw bolt (l) into the lower clamp bracket(H) andusingclamp pad
screw (r) attachclamp (k) to the end of the bolt (I).
3. Hook lower clamp bracket (H) in to one of the top 2 (of the 3)
positions provided.
4. Position clamp bracket and poleassembly (F) onto work surface in
desired location.
5. Using knob (j) tighten securely.
6. For applications requiring increased tightness, slide knob up bolt to expose
the bolt head and using a 9/16”wrench tighten the bolt to 90 in-lbs.
Caution: DO NOT OVERTIGHTEN

Avia Pole-mount Monitor Arm Assembly Instructions
Page 3 of 3
Adjusting the torque:
1. Remove joint cap (L) from the top of the joint using a small flat
head screw driver.
2. Unscrew the cable manager (M) from the bottom of the joint.
3. Holding the bolt in the top of the joint with a 9/16” socket, use a
second 9/16” socket on the nut in the bottom of the joint to adjust
the torque setting.
4. Replace cap and reassemble cable manager.
Using the Height Adjustable Cable Manager:
1. Remove cable manager (N) by pinching at release points.
2. Lay cables in cable manager.
3. Snap cable manager back into place. Note text indication
“FRONT” inside cable manager.
Mounting the Monitor:
Quick Connect Bracket:
1. Affix Quick Connect Bracket to screen, make sure
arrow is pointing up.
2. Make sure faceplate arrow is also pointing up then slide
monitor mount assembly onto faceplate until bottom tab
clicks onto faceplate.
3. To remove the monitor, depress tab and remove from
monitor mount assembly.
Adjusting the Tilt Tension:
If the monitor drops or is too tight, adjust the tension screw at the side
of the head as shown using the 3/16” Allen key.
i
1
2
3401 Madison Street
Skokie, IL 60076
[phone]
[email protected]