Applied LA12-18 User manual

Applied
Truss and Electronics
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
REVISED: 8/30/2018
1
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com
ATTENTION!
750 lb WEIGHT LIMIT

Applied
Truss and Electronics
Motor Point
without
5/8 Shackle
WINCH ONLY CONFIG.
OPTION (A)
Winch
Plate
Motor Bracket
1/4 & 1/2 Ton
Chain Hoists
Motor Point
with 5/8 Shackle
WINCH/MOTOR CONFIG.
OPTION (B)
Winch
Plate
2
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
REVISED: 8/30/2018
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com

Applied
Electronics
Proudly Made in USA
?
Applied
Truss and Electronics
BILL OF MATERIALS
(1) BASE PLATE
(2) FRONT LEGS
(2) REAR LEGS
(2) FRONT ARCHED BRACES
(2) REAR STRAIGHT BRACES
(1) 12IN EURO BOX HINGE
(1) 12IN EURO BOX 6' LENGTH
(1) 12IN EURO BOX ARCHED SECTION
(1) HEAD-BLOCK EURO TRUSS
(1) CLAMPING 3RD WHEEL
(1) WINCH
MOTOR OPTION (REPLACES WINCH)
(2) MOTOR HANGING BRACKET
(1) 5/8" Shackle - Motor Point
(1) 3/8" STEEL SLING - 5' LENGTH
** CHAIN HOIST NOT INCLUDED **
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
3
REQUIREMENTS FOR SAFE USE
1) Build Tower on flat surface.
2) Thick wood or metal plates under leveling jacks.
3) Don't lift load until tower is fully assembled.
4) Maximum Load Capacity is 750Lbs
THIS TOWER SHOULD BE ASSEMBLED/ERECTED AND
BALLASTED BY QUALIFIED INDIVIDUALS.
** BALLAST IS NOT PROVIDED**
* BALLAST REQ'D OUTDOORS,
SEE PAGE 14 FOR BALLAST INSTRUCTIONS.*
ALWAYS...IF YOU HAVE QUESTIONS, PLEASE CALL!
REVISED: 8/30/2018
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com

Applied
Truss and Electronics
Third Wheel
MLAT-12-TW
12x12 Euro Box 6ft
MLAT-12-6TS
12x12 Euro Hinge
MLAT-12-H
12x12 Euro Box
Arched Section
MLAT-12-CTS
X 54
X 58
1-1/4in
X 58
Front Brace
MLAT-12-FB
3in
Front Leg
MLAT-12-FL
Rear Leg
MLAT-12-RL
Rear Brace
MLAT-12-RB
Head Block
MLAT-12-HB
X 1
Base Plate
MLAT-12-BS
X 2
Motor Brackets
MLAT-12-BS
(Optional)
X 1
Steel Sling
93-008
5 ft
(Optional)
X 4
91-330
X 1
Winch
91-506
X 1
Lower Yoke
1-18-700-LY
X 1
Upper Yoke
1-18-700-UY
4
LA12-18 MINI LINE ARRAY TOWER
PARTS SHEET / PER TOWER
X 1
X 1
X 1
X 2
X 2
X 1
X 1 X 2
X 2
X 4
Winch Cable
91-511
(not shown)
Base Leveling Feet
MLAT-12-BLF
(not shown)
Leg Leveling Feet
MLAT-12-LLF
Lifting Arm
1-18-700A
X 1
3/8in Hardware
REVISED: 8/30/2018
MATERIAL
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com

Applied
Truss and Electronics
WINCH MOUNTING BRACKET
(A)
REAR FRONT
STEP 1
1) Attach "Hinge Section" to the base plate with provided 3/8 x 1-1/4 fasteners.
2) IF USING A HAND WINCH ATTACH TO MOUNTING BRACKET (A)
3) Temporarily bolt hinge closed.
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
5
ASSEMBLY
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com
REVISED: 8/30/2018

Applied
Truss and Electronics
LONG LEGS IN FRONT
RIGGING SHACKLE
FACES REAR
SHORT LEGS IN REAR
FRONT
REAR
PINS/LANYARDS
#91-350
Hinge not shown for clarity.
STEP 2
1) Attach "Legs" to the base plate with provided fasteners.
2) Level all feet before weight is placed on base.
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
6
ASSEMBLY
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com
REVISED: 8/30/2018

Applied
Truss and Electronics
29.00
STEP 3
1) Bolt remainder of trusses to hinge with provided 3/8 x 1-1/4 fasteners.
2) Bolt "Head-block" to arched section with provided 3/8 x 1-1/4 fasteners.
3) Clamp the "Third-Wheel" to the arched section at the location indicated by the labels.
FRONT
11
2
3
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
7
ASSEMBLY
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com
REVISED: 8/30/2018

Applied
Truss and Electronics
Hand Winch
STEP 4 (WINCH)
1) Attach Winch with bolts provided.
2) Follow illustration/directions to attach cable
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
8
WINCH
Attaching cable to winch
A) Wrap at least 2 turns of cable around the
drum of the winch.
B) Feed at least 5in of cable thru the hole on
the right side of winch drum, same side as
crank-handle.
C) With your thumb bend a loop in the cable,
as illustrated.
D) Loosen the capture nut and carefully feed
the loop thru the catch and tighten the
capture nut with a wrench.
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com
REVISED: 8/30/2018

Applied
Truss and Electronics
Applied
Truss and Electronics
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
LIFTING
ARM
9
STEP 5A
ASSEMBLE LIFTING ARM.
1) Unbolt upper tube from storage position and rebolt in lifting position.
2) Pin upper and lower yokes to lifting positions.
3) Install cable on Lifting Arm Winch.
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com
REVISED: 8/30/2018

Applied
Truss and Electronics
Position lifting arm and
connect to lower hinge
section.
CAUTION: ONLY LOAD TOWER AFTER
BRACES ARE ATTACHED AND COMPLETELY ASSEMBLED
STEP 5
INSTALLING TOWER CABLE.
1) Run cable from Winch over head-block.
2) Position & Connect Lifting Arm.
3) Secure Lifting Arm to hinge with pins on lower yoke.
LA12-18 MINI LINE ARRAY TOWER
INSTRUCTIONS
TOWER
CABLE
10
PROUDLY MADE IN THE U.S.A.
722 Blue Crab Road
Newport News, VA 23606
757.591.9371 / fax [phone]
www.appliednn.com
REVISED: 8/30/2018