APR TB-10010 User manual

APR - 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Website: APR-Rework.com
TB-10010 Page 1 of 5 © 2020 DESCO INDUSTRIES INC
Employee Owned
Scorpion Auto-Focus Camera
Installation and Operation Instructions
Description
The APR 670029 Scorpion Auto-Focus Camera pairs
with the Scorpion Rework System to provide solder
reflow visibility and rework inspection. The auto-focus
camera features 1080p resolution and 60 fps image
quality for sharp imagery with minimal lens configuration
and no motion blur. The quick knob on the included
articulating arm easily locks the camera's orientation,
so it can transition between side-view and overhead
positions for multi-purpose use. Embedded software
saves and recalls images and videos onto an SD
card for quality control documentation. The Scorpion
Auto-Focus Camera includes the camera, macro zoom
lens, LCD monitor, LED ring light, articulating arms, and
wireless mouse.
Packaging
1 Auto-Focus Camera
1 Macro Zoom Lens
1 LCD Monitor, 12"
1 LED Light Ring with North American Power Cord
1 Camera Articulating Arm
1 Monitor Articulating Arm
1 Wireless Mouse
1 SD Memory Card, 16 GB
1 HDMI Cable, 5'
2 Power Adapter, 12 VDC, with interchangeable plugs
(North America, UK/Asia, Europe)
1 Mounting Block with Knob and Washer
2 Flat Head Screw, M6 x 16 mm
April 2020
USER GUIDE TB-10010
Figure 1. APR 670029 Scorpion Auto-Focus Camera
Installation
1. Use a 4 mm hex key and the two included flat head
screws to secure the mounting block to the left
gantry arm on the Scorpion Rework System.
Figure 2. LED Ring Light, Auto-Focus Camera with
Macro Lens, LCD Monitor, Camera Articulating Arm,
Monitor Articulating Arm, and Wireless Mouse
Figure 3. Using the two at head screws to secure the
mouning block to the left gantry arm on the Scorpion
Rework System
1
2
2. Insert the camera articulating arm's stud into the
mounting block. Use the mounting block's knob to
tighten the arm into place.

APR - 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Website: APR-Rework.com
TB-10010 Page 2 of 5 © 2020 DESCO INDUSTRIES INC
Employee Owned
3. Tighten the quick knob on the camera articulating
arm to lock its movement.
6. Use the clamp on the monitor articulating arm to
secure it to the left gantry arm on the Scorpion
Rework System.
Figure 4. Using the knob on the mounting block to
secure the camera articulating arm into place
Figure 5. Tightening the quick knob on the camera
articulating arm to lock its movement
4. Remove the protective plastic cap from the
auto-focus camera's lens, and connect the macro
lens.
5. Secure the auto-focus camera to the platform on the
camera articulating arm using the grey knob.
Figure 6. Securing the auto-focus camera to the platform
on the camera articulating arm
Figure 7. Using the clamp to secure the monitor
articulating arm to the left gantry arm on the Scorpion
Rework System

APR - 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Website: APR-Rework.com
TB-10010 Page 3 of 5 © 2020 DESCO INDUSTRIES INC
Employee Owned
7. Use the mounting clip located at the back of the
LCD monitor to secure it to the opposite end of the
monitor articulating arm.
Figure 8. Securing the LCD monitor to the monitor
articulating arm
8. Connect the HDMI cable to the HDMI port located
on the bottom of the LCD monitor. Connect the
opposite end of the cable to the HDMI port located
on the back of the auto-focus camera.
9. Insert the SD card and the wireless mouse's USB
transmitter into their appropriate connectors located
on the back of the auto-focus camera.
10. Secure the LED light ring onto the macro lens using
its three thumbscrews. Connect its power cord into
an AC outlet. Enable the power switch on the LED
light ring.
NOTE: The LED light ring is rated to accept 100-240
VAC and includes a NEMA 5-15p power plug. A
plug adapter must be sourced and used if the LED
light ring is to be used in a region without a NEMA
5-15 outlet.
11. Connect one of the two included power adapters
to the power jack located on the bottom of the LCD
monitor. Connect the opposite end to an AC outlet.
Enable the power switch on the LCD monitor.
12. Connect the second power adapters to the power
jack located on the back of the auto-focus camera.
Connect the opposite end to an AC outlet. Enable
the power switch on the auto-focus camera.
Operation
Side-View Reflow Inspection
1. Use the quick knob on the camera articulating arm
to position the auto-focus camera in a side-view
orientation. Loosen the knob to free the arm's
movement, and tighten the knob to lock the arm in
place.
Figure 9. Scorpion Auto-Focus Camera installed on the
Scorpion Rework System
Figure 10. Tightening the quick knob on the camera
articulating arm to lock the auto-focus camera into side-
view orientation
2. Adjust the macro lens and LED ring light until the
desired results are achieved on the LCD monitor.
Figure 11. Adjusting the macro lens while the auto-focus
camera is in side-view orientation

APR - 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Website: APR-Rework.com
TB-10010 Page 4 of 5 © 2020 DESCO INDUSTRIES INC
Employee Owned
Figure 12. Tightening the quick knob on the camera
articulating arm to lock the auto-focus camera into
overhead orientation
Figure 13. Adjusting the macro lens while the auto-focus
camera is in overhead orientation
3. Use the wireless mouse to navigate through the
camera's embedded software and control its
auto-focus, photo, and video features.
Overhead Rework Inspection
1. Use the quick knob on the camera articulating arm
to position the auto-focus camera in an overhead
orientation. Loosen the knob to free the arm's
movement, and tighten the knob to lock the arm in
place.
2. Adjust the macro lens and LED ring light until the
desired results are achieved on the LCD monitor.
3. Use the wireless mouse to navigate through the
camera's embedded software and control its
auto-focus, photo, and video features.
Specifications
Auto-Focus Camera
Input Voltage and
Frequency
(External Adapter)
AC/DC Power Adapter
Power Input:
100-240 VAC, 50/60 Hz
Power Output:
12 VDC @ 1.50 A
Cable Length:
5 ft. (1.5 m)
Image Sensor 1/2.86 inch Panasonic Full HD
2.0MP
E󰀨ective Pixels 1920 x 1080
Frame Rate 60 fps
Denition More than 1200 lines
Housing Aluminum
White Balance Automatic, Manual, Continuous
Brightness Control Automatic, Manual, Continuous
Color R/G/B adjustable
Edge Enhancement Yes
OSD Yes (HDMI mode)
Edge Enhancements Yes
Freeze Image Yes
HDR Yes
Crosshair Multi-color, small, or large
Horizontal & Vertical
Lines
Multi-color, two lines for each
Noise Reduction Supported
SD card slot Supports up to 32 GB
HDMI Port 1080p
USB Port USB 2.0
Dimensions 3.1" x 2.8" x 3.6"
(78 mm x 70 mm x 92 mm)
Weight 1.2 lbs (0.5 kg)

APR - 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Website: APR-Rework.com
TB-10010 Page 5 of 5 © 2020 DESCO INDUSTRIES INC
Employee Owned
Limited Warranty, Warranty Exclusions, Limit of
Liability and RMA Request Instructions
See the APR Warranty -
APR-Rework.com/Limited-Warranty.aspx
Macro Lens
Max Magnication 61.9X
Back Focal Length 24.28
EFL 18-108 mm
Exit Pupil Position 238.60
Focus Control Manual
Format 2/3"
F Stop 2.5 - Close
Iris Control Manual
Zoom Control Manual
Length 6.7" (171 mm)
Weight 1.3 lbs (0.6 kg)
LED Light Ring
Input Voltage and
Frequency
(Internal Adapter)
AC/DC Power Adapter
Power Input:
100-240 VAC, 50/60 Hz
Power Output:
24 VDC
Power Consumption:
4.5 W
Power Cord Length:
5.5 ft. (1.7 m)
Light Intensity 35,000 lux
Dimensions 3.8" x 4.7" x 1.3"
(97 mm x 120 mm x 33 mm)
Weight 0.5 lbs (0.2 kg)
Camera Articulating Arm
Load Capacity 6.6 lbs (3.0 kg)
Max Length 20.9" (531 mm)
Weight 2.4 lbs (1.1 kg)
Monitor Articulating Arm
Load Capacity 4.4 lbs (2.0 kg)
Max Length 11.2" (284 mm)
Weight 0.6 lbs (0.3 kg)