APTO 6000-0032-5008 User manual

INSTRUCTION MANUAL
MONITOR HOLDER
DESIGNED BY PJ PRODUCTION & HANS THYGE & CO
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©

INSTRUCTION MANUAL
PARTS
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
MONITOR HOLDER
Nordic Dark Blue: 6000-0032-5008
Danish Dusty Green: 6000-0032-7033
Scandinavian Matte Black: 6000-0032-9000
1 x monitorarm 1 x VESA 1 x cable clip1 x holder

INSTRUCTION MANUAL
WHAT YOU WILL NEED
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
1 x ALLEN WRENCH
The Allen wrench is included in the multi
clamp box
4 x SCREWS
Four size fitting screws for the VESA. Please
note that these are not included!
1 x MULTI CLAMP
Nordic Dark Blue: 6000-0000-5008
Danish Dusty Green: 6000-0000-7033
Scandinavian Matte Black: 6000-0000-9000
1 x SCREWDRIVER
One screwdriver. Please note that this is not
included!

INSTRUCTION MANUAL
STEP 1
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
Carefully connect the monitorarm and the holder

INSTRUCTION MANUAL
STEP 2
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
Carefully lead the tube through the hole at the top of the multi clamp

INSTRUCTION MANUAL
STEP 3
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
The finger screw must be open entirely before continuing. Now carefully insert the tip of the Allen wrench into the hexagon cross
section of the socket screw and turn the wrench in a clockwise fashion until the socket screw has been sufficiently tightened.

INSTRUCTION MANUAL
STEP 4
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
The monitor holder can now be attached to the prefered surface.

INSTRUCTION MANUAL
STEP 5
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
When the placement of the monitor holder is correctly, then tighten the finger screw completely.

INSTRUCTION MANUAL
STEP 6
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
The VESA must be aligned with the display before continuing. Now connect the VESA and display with four size fitting screws.
When these are connected, carefully insert the tip of the screwdriver into the hexogon cross section of the screw and turn the
screwdriver in a clockwise fashion until the screw has been sufficiently tightened. Repeat the process with the remaining three
screws.

INSTRUCTION MANUAL
STEP 7
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
Carefully lead the VESA through the monitor holder’s adjustment system.

INSTRUCTION MANUAL
STEP 8
Designed by PJ Production & Hans Thyge & Co // Hårup Skovvej 2, 8600 Silkeborg, Danmark // + 45 86 81 23 75 // www.aptocollection.dk
Copyright ©
Use the enclosed cable clip to control wires and cables from the display.

DANISH DESIGN
Copyright ©
Hårup Skovvej 2, 8600 Silkeborg, Danmark
+ 45 86 81 23 75 // www.aptocollection.dk