Aqua-Marina AM-20NU User manual

USER MANUAL
AM-20NU
STANDUP PADDLE BOARD
EN
INFLATABLE

2
SAFETY
There is a risk of serious injury or death from drowning. Paddle
sports can be very dangerous and physically demanding. The
user of this product acknowledges, understands, and assumes the
risks involved in paddle sports. Observe the following warning
labels and safety standards carefully whenever using this product.
GENERAL PADDLING INFORMATION
This manual has been compiled to help you operate your
Inflatable Stand Up Paddle Board (Hereinafter referred to as ISUP)
with safety and pleasure. It contains details of the ISUP, the
equipment supplied, and information on their operation. Please
read it carefully and familiarize yourself with the ISUP before
using it.
For your own safety and that of your equipment,
make sure to take the following precautions.
Failure to follow warning notices and instruction
may result in property damage, serious injury or
death.
WARNING
aquamarina.com

3
WARNING LABEL INSTRUCTIONS
140kg
308lbs
MANDATORY INSTRUCTION
• Wear personal flotation device
• Read instructions first
• Fully inflate all air chambers
• Numbers of users
• Max. load capacity
• Safe distance to shore 150 m (492.1’)
PROHIBITION INSTRUCTION
• Do not use in white water
• Do not use in breaking waves
• Do not use in offshore current
• Do not use in offshore wind
•
Not for children 14 years old
and below
ATTENTION / DANGER / WARNING
• Design working pressure
• No protection against drowning
MANDATORY INSTRUCTION
• Swimmers only
PRODUCT SERIAL NUMBER
• Item No.
• Manufacturer information

OrientalRecreationalProducts (Shanghai) Co., Ltd.
1699DayeRoad, Fengxian Shanghai, China 201402
18psi/1.24bar
NOPROTECTIONAGAINST DROWNING
AUCUNEPROTECTIONCONTRE LA NOYADE
KEINSCHUTZGEGEN ERTRINKEN
SINPROTECCIÓNCONTRA EL AHOGAMIENTO
SWIMMERSONLY
LESNAGEURSSEULEMENT
NURFÜRSCHWIMMER
SÓLOLOSNADADORES
ItemNo.: BT-18RP
CN-ORP
1
130kg
287lbs
D-ring
D-ring
Towing eyelet
High pressure
recessed valve
EVA deck
Slide-in fin box
4
ACCESSORY
SPECIFICATION
D-rings
Towing eyelet
Neoprene carry handle
Bungee cord stopper
Heavy Duty Slide-in Center Fin
Specially Designed
Slide-in Center Fin
MODEL
NUTS
AM-20NU
SIZE
10‘6“ x 32“ x 6“
320 x 81 x 15cm
FIN VOLUME
300 L
MAX. RIDER WGT
308 LBS / 140 KG
MAX. AIR PRESSURE
18 PSI

INSTRUCTION FOR ASSEMBLING
AND DISASSEMBLING
Pump Set Up And Inflation
A
B
1. Release the valve cover by twisting counter-clockwise. Ensure the valve is
clear from debris, sand, or dirt before releasing.
2. Push valve button in and turn counter-clockwise 90 degrees so it pops up
and is in the “OUT” position.
3. Insert the pump hose and twist it 45 degree clockwise to lock in place.
Inflate until you reach the required pressure.
12PSI minimum for proper inflatable boards
operation and 18PSI maximum. Over inflation
will void your warranty.
Connect the pump hose to the
gauge housing and secure it tightly.
5
* Pump is not included in the package.

6
• Electric Pumps can be used to inflate board up to 80-90%. However, the
remaining pressure required should be achieved by using the hand
pump to avoid over-inflation.
• Do not use air compressors as this voids warranty of board.
• Before long trips, ensure the board has been inflated and has
maintained pressure for a minimum of 24 hours.
PRECAUTION & TIPS
C
Inflate Faster With Less Effort
•Use full range of the pump
cylinder while keeping your
arms extended.
•Bend your knees and use the
body weight.
1. Use DOUBLE ACTION mode by closing the air-tap to pump the board
up to 7 psi.
2. Switch to SINGLE ACTION position by opening the air-tap to pump the
board up to 18 psi.
3. After inflation, return the valve cover and tighten in clockwise direction
to lock in place.
DOUBLE
ACTION
SINGLE
ACTION

Slide-in Center Fin Installation
Once the board is inflated, slide in the Center Fin to the fin box and secure
the push-in pin.
7
D
E
Deflation
To deflate your board, follow the instructions below.
1. Release valve cap by twisting counter-clockwise. Ensure the valve is
clear from debris, sand, or dirt before releasing.
2. Push valve button in and turn clockwise to lock it in DOWN position.
F
1. Roll up your board from nose to tail, pushing all air out as you roll, or
using the pump on “deflate” position for faster deflation.
2. Press all air out of the board, return valve cover, and tighten in
clockwise direction to lock in place.
or

1. Clean the area around the cut or puncture using acetone or M.E.K.
2. Draw the outline of the patch using chalk or pencil (do not use ink).
Cut the patch, cover the cut or puncture with approximately 2.5cm (1
inch) overlap on all sides.
3. Apply tape along the outline of the patch. This will prevent the glue
from spreading outside the patch area.
4. Apply glue on both the board and patch using a brush or other
applicator. Make sure the glue is spread evenly and completely over the
board and patch. Let the glue dry for 5 minutes.
4 5 6
8
HOW TO REPAIR A CUT OR PUNCTURE
IN YOUR INFLATABLE BOARD
GSUPPLIES REQUIRED
• Glue (AQUASEAL® is recommended)
• Acetone or methyl ethyl ketone (M.E.K.)
•Hairdryer
•Brush
•Tape
•Spatula or spoon
•Towel
(Not provided in the SUP board package)
1 2 3
Glue
M.E.K.

9
24h Allow the glue to cure with
the board un-inflated for 24
hours prior to use.
H
HOW TO FIX A LEAKING VALVE
open
close
open
close
1. Inflate your board up to the max air
pressure
2. Stick your valve wrench down inside of
valve and turn clockwise to tighten the
valve back down onto the board
1. Completely deflate your board
2. Undo the dust cap and insert the valve wrench into the valve and
twist counterclockwise to remove the valve
5. Apply the patch starting on one side and move towards the other side
Be careful not to trap any air bubbles.
6. Use a hairdryer to gently heat the area to ensure a good bond between
the patch and the board.
Use a metal spatula or spoon and firm pressure to ensure a good bond
and to remove any air bubbles.
A. Try to tighten the valve
B. Re-install or replace a valve

10
NOTE: Correctly use the wrench by pressing it with
one hand on top.
open
close
3. Check the rubber ring to make sure that it is in the correct position,
tight around the valve and there is no debris in the way
4. Be sure the pin spring is functioning properly and that there are no
cracks along the edges
5. Ensure there are no strings from the drop stitching material
6. Note the bottom piece of the valve is not attached to anything
7. Fit the valve back into your board
8. Align all the threads and twist to tighten
9. Once the valve is hand tight, use the valve wrench to seal completely
Rubber Ring