Brunswick Metro User manual

Metro
POCKET BILLIARD TABLE
INSTALLATION MANUAL
www.brunswickbilliards.com
SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
TM
51-905486-001 SEPTEMBER2005

PAGE 2 BRUNSWICK INSTALLATION MANUAL
METRO
NOTE: Please use the instructions in this manual to assemble the tables
shown below. Illustrations may be different depending on the table
being assembled. Also note that careful handling of all components
will assure damage-free assembly.

BRUNSWICK INSTALLATION MANUAL PAGE 3
METRO
BASEFRAME AND LEG ASSEMBLY
FIGURE ONE
Step #1: Loosely assemble the two side sills to the four
cross support sills as shown in Figure One with 5/16-18
x 4” hex head bolts, 5/16 flat washers and 5/16-18 weld
nuts.
Step #2: Attach two slate attach cleats to each end of the
baseframe as shown in Figure One with 5/16-18 x 5-1/2”
hex head bolts, 5/16 flat washers and 5/16-18 hex nuts.
Position flush with the top of the sill and securely tighten
FIGURE ONE
FIGURE TWO
Step #3: Set the legs out with the levelers up. Run out
about 1/4” to assure that they are free to rotate.
Step #4: Set the legs out, upright at the four corners and
set the assembled baseframe on top.
FIGURE TWO
FIGURE THREE
Step #5: Set a leg attach bracket in each corner of the
baseframe on top of the leg.
Step #6: Loosely attach the brackets to the leg using 5/
16-18 x 1-1/4” hex head bolts and 5/16 flat washers.
Step #7: Loosely attach the baseframe to the brackets
using 3/8-16 x 2-3/4” hex head bolts, 3/8 flat washers and
3/8-16 hex nuts.
FIGURE THREE

PAGE 4 BRUNSWICK INSTALLATION MANUAL
METRO
BASEFRAME AND LEG ASSEMBLY
(CONTINUED)
FIGURE FOUR
Step #8: Measure the baseframe assembly diagonally
and adjust as required to obtain the same measurement
to assure the baseframe is square. With all joints flush
and legs aligned properly, tighten all hardware securely.
FIGURE FOUR
FIGURE FIVE
Step #9: Screw #10 x 1” pan head tapping screws
through the top of each leg bracket into the leg.
FIGURE FIVE
FIGURE SIX
Step #10: Position the baseframe and leg assembly in its
final location. Level the baseframe with your preferred
level by rotating the leg levelers. The levelers should be
rotated out atleast 1/4” to allow for further leveling when
the slate is attached.
NOTE: Try to leave atleast 5’ between the outer edge
of the baseframe to any wall.
FIGURE SIX

BRUNSWICK INSTALLATION MANUAL PAGE 5
METRO
SLATE ASSEMBLY AND LEVELING
FIGURE ONE
Step #1: Position the center slate section evenly between
the two slate joint supports as shown, with an equal
amount of overhang at each side of the base frame.
FIGURE ONE
FIGURE TWO
Step #2: Position the two end slate sections on the base
frame as shown. Be sure that the penciled arc forms a
radius as shown.
Step #3: Recheck to be sure the slate has an equal
amount of overhang around the base frame.
Step #4: Using the 12 countersink holes in the slate as a
template, pilot drill 5/32" diameter holes into the mount-
ing cleats.
Step #5: Securely fasten the end slate sections at both
ends of the table with 1/4 x 1-3/4" flat head screws for
UNFRAMED slate or #14 x 3" flat head screws for
FRAMED slate.
Step #6: With a precision tool, level each end slate
section by driving wooden slate wedges (provided)
between the top of the base frame and bottom of the
slate as shown. Keep the wedges as close to the
countersink holes as possible.
Step #7: With both end slates perfectly level, continue
fastening the end slates at the joints. Recheck for
levelness and, if necessary, back the screws out and
adjust the shim position. Then, retighten the slate
attaching screws.
Step #8: When satisfied that both end slates are level,
shim the center slate section as required to obtain a
flush fit at both joints, then screw the center slate down.
Step #9: Slate joints can now be filled with Rock Hard
putty or wax. Lightly sand or scrape across the joints
after grouting.
FIGURE TWO

PAGE 6 BRUNSWICK INSTALLATION MANUAL
METRO
SLATE ASSEMBLY AND LEVELING
(CONTINUED)
FIGURE THREE
Step #10: From the end of a bed cloth, cut strips of cloth
approximately 1-1/2" wide by 8" long and glue the strips
to the pocket cutouts. This is important as this will
provide cushioning from ball impact and the bed cloth
will last much longer.
Step #11: Clean top of slate thoroughly with a damp
cloth before applying the bed cloth.
FIGURE THREE

BRUNSWICK INSTALLATION MANUAL PAGE 7
METRO
ATTACHING BILLIARD CLOTH TO
UNFRAMED SLATE
Before attaching the billiard cloth, clean slate thoroughly.
FIGURE ONE
Step #1: Lay the bed cloth over the top of the slate, nap
side up. Leave an equal amount of cloth overhang at the
ends and sides of the slate.
FIGURE ONE
FIGURE TWO
Step #2: At the head end of the table, fold the cloth back
away from the edge of the slate and spray a coat of
contact adhesive (not included) as indicated by the
shaded area of the edge of the slate. Hold the can
approximately 4-8" from the area to be coated. Coat the
underside of the slate also. Place a piece of protective
paper or card board on the top surface of the cloth.
CAUTION: Do not allow any adhesive to get on the
top surface of the cloth.
FIGURE TWO
FIGURE THREE
Step #3: Attach the cloth at #1.
Step #4: Stretch the cloth across the table at #2. Fold
the cloth overhang underneath the edge of the slate at
the end.
Step #5: Fold the cloth back at the foot end of the table
and repeat Step 1.
Step #6: Stretch the cloth from #1 to #3 and press into
position.
Step #7: Stretch the cloth #3 to #4, pulling from #1 and
#2. Press into place.
FIGURE THREE

PAGE 8 BRUNSWICK INSTALLATION MANUAL
METRO
ATTACHING BED CLOTH TO
FRAMED SLATE
Before attaching the billiard cloth, clean slate thoroughly.
FIGURE ONE
Step #1: Lay the bed cloth over the top of the slate, nap
side up, with the nap running from the head end to the
foot end of the table.
NOTE: In determining the direction of the nap, run
your hand lightly over the surface of the cloth. If it
meets resistance, it is going against the nap.
Step #2: Leave only enough cloth overhang at the head
end and left side to permit tacking into the wood slate
frame. Leave the balance of cloth overhang at the foot
end and right side.
NOTE: Do not spread tacks on the bed cloth. Keep them
in a container that slides over the cloth.
Step #3: Tack or staple the cloth securely to the wood
frame at #1 with two tacks or staples approximately 2"
apart.
Step #4: Stretch the cloth across the table and tack or
staple securely at #2 with two tacks or staples 2" apart.
FIGURE ONE
FIGURE TWO
Step #5: Stretch the cloth from #1 to #3 and tack or
staple securely into the wood frame at the left side of the
table. See Figure B.
Step #6: Stretching the cloth across the table from #3
and pulling from #2, tack or staple the cloth at #4.
FIGURE TWO
FIGURE THREE
Step #7: On the left side, stretch the cloth tightly from
#1 toward the side pocket opening and tack or staple
securely at #5.
Step #8: Repeat Step 5, stretching the cloth from #3 and
tacking or stapling at #6.
Step #9: On the right side of the table, grasp the cloth
firmly and stretch across the table from #5 and toward
the side pocket from #2 and tack or staple at #7.
Step #10: Repeat Step 7, stretching from #6 and toward
the side pocket from #4 and tack or staple at #8. FIGURE THREE

BRUNSWICK INSTALLATION MANUAL PAGE 9
METRO
ATTACHING BED CLOTH TO
FRAMED SLATE (CONTINUED)
FIGURE FOUR
Step #11: At location #9, cut a short slit in the cloth at
the edge centered on the side pocket opening. Grasp the
cloth firmly above this slit, pull the cloth into the side
pocket opening and tack or staple to the wood frame.
Complete fastening of the cloth to the side pocket
opening, making sure the cloth is tacked or stapled to the
wood frame.
Step #12: Stretching the cloth tightly across the table
from location #9, repeat Step 11 at location #10.
FIGURE FIVE
Step #13: At the head end of the table, tack or staple the
cloth at location #11, maintaining uniform overhang.
Step #14: Pull the cloth from location #11 toward
location #12 and tack or staple securely along the wood
frame, keeping the cloth even along the head end.
Step #15: Stretch the cloth firmly from location #11 to
the foot end of the table and tack or staple at location
#13.
Step #16: Stretch the cloth tightly from locations #12
and #13 toward location #14 and tack or staple securely
along the wood slate frame.
FIGURE SIX
Step #17: Tack or staple all of the left side on 2" centers
keeping the cloth even along the wood frame.
Step #18: Tack or staple the balance of the head end on
2" centers also keeping the cloth even along the wood
frame.
Step #19: Stretch the cloth tightly toward the foot end of
the table, tacking or stapling on 2" centers along the
wood frame at the foot end.
Step #20: Stretch the cloth tightly across the table to the
right side, tacking or stapling on 2" centers all the way
along the wood frame at the right side.
FIGURE SEVEN
Step #21: Stretch the cloth into the corner pocket
openings and tack or staple to the wood slate frame.
Step #22: Trim off excess cloth around the perimeter of
the slate. Locate the eighteen (18) rail attach holes and
cut clearance holes in the cloth with a sharp knife.
NOTE: Occasionally cloth will stretch, leaving wrinkles
at the pockets. To retighten, remove apron, one end rail
and one side rail. Pull cloth taut, and retack or restaple
along the open end and side to restore original tightness.
FIGURE FOUR
FIGURE FIVE
FIGURE SIX
FIGURE SEVEN

PAGE 10 BRUNSWICK INSTALLATION MANUAL
METRO
ATTACHING RAIL CLOTH
CORNER POCKET
FIGURE ONE
Step #1: Place cloth on rail with the back side down.
The cloth should have equal amount of overhang at both
ends of rail and extend 1/2" over the featherstrip groove
on the cushion side as shown.
Step #2: Except for approximately 3" at end of rail, tap
featherstrip down with a tapping block and hammer,
starting at center of rail. Stretch cloth tightly toward
each end of rail and tap featherstrip down.
FIGURE ONE
FIGURE TWO
Step#3: At each end of rail, pull the cloth toward the
rubber cushion an additional 3/4". Then tap remainder of
featherstrip down.
FIGURE TWO
FIGURE THREE
Step #4: Trim the cloth on cushion side of featherstrip
along the total length of featherstrip as illustrated.
FIGURE THREE
FIGURE FOUR
Step #5: Fold the cloth down over front of rail, then
using thumb and forefinger as a guide along front edge
of the cushion to keep the tapping block at rear edge of
featherstrip, tap the featherstrip down flush with rail
surface as shown.
NOTE: Never try to tap a featherstrip flush with just a
hammer as you will surely dent the rail surface behind the
featherstrip.
FIGURE FOUR
FIGURE FIVE
Step #6: Turn rail over and at corner pockets fold the
cloth over the mitred edge as shown, stretching tightly
and working out any wrinkles as you staple three places
in area shown.
FIGURE FIVE