Aquabotix Technology Corporation AQUALENS Series User manual
underwater viewing system
VERSION 1
© Aquabotix Technology Corporation. All rights reserved. 10.07.2011
Trademarks used in this guide, Aquabotix and AquaLens, are trademarks of
Aquabotix Technology Corporation. Other names mentioned in this guide may be
trademarks or registered trademarks of their respective owners.
Aquabotix reserves the right to make changes to the specications of the
AquaLens at any time without notice. Also, Aquabotix may alter any or all
documentation without notice.
The purpose of this manual is to provide AquaLens users with a
clear understanding of operating procedures. If further information
website: www.aquabotix.com
Table of Contents
Legal Disclaimer
Important Safety Instructions ___________________________________
Safety and Operational Warnings ________________________________
Additional Restrictions On Use __________________________________
AquaLens Assembly
Overview ______________________________________________________
Pole Attachment ______________________________________________
Topside Box Connections _______________________________________
LCD Screen Attachment ________________________________________
Removing Dome _______________________________________________
Maintenance
Inserting Or Replacing Batteries ________________________________
Recomended Replacement Periods _____________________________
Replacing O-ring _______________________________________________
Replacing Moisture Absorbing Pack ____________________________
Cleaning Dome _______________________________________________
Preventing Fogging On Dome ___________________________________
After Water Care ______________________________________________
Troubleshooting ________________________________________________
Specications _________________________________________________
Warranty ______________________________________________________
1
1
2
4
5
6
7
7
8
9
9
10
10
10
10
11
11
12
Important Safety Instructions
Assemble and use AquaLens only as instructed by this manual.
Read and follow these important safety instructions and the detailed
assembly in this manual prior to using the Aqualens.
Follow all safety and operational warnings.
Heed all additional restricitons on use.
Refer all non-routine service issues to Aquabotix at www.aquabotix.com
Safety and Operational Warnings
Assemble AquaLens in a safe, dry place. Do not assemble while
submerged in water or allow Aqualens to get wet before it is fully
assembled and enclosed in the watertight dome. Do not assemble with
wet hands.
AquaLens is powered by eight (8) AA Alkaline batteries. Do not use any
other type of battery or powering device for AquaLens. Caution should
be used when inserting or changing batteries.
Do not attempt to insert or change batteries into AquaLens while
submerged in water. Do not let the battery assembly area get wet. Do
not assemble with wet hands.
When using topside power to operate your AquaLens, use caution to
prevent shock or damage.
The AquaLens dome must be completely secured to keep it watertight.
Check the security of the dome before submersion. To tighten, line up
the grooves and turn clockwise until it locks.
The topside box and LCD screen are not waterproof. Do not submerge
the topside box or LCD screen in water. Do not let the topside box or
LCD screen get wet.
1Legal Disclaimer
Table of Contents
Legal Disclaimer
Important Safety Instructions ___________________________________
Safety and Operational Warnings ________________________________
Additional Restrictions On Use __________________________________
AquaLens Assembly
Overview ______________________________________________________
Pole Attachment ______________________________________________
Topside Box Connections _______________________________________
LCD Screen Attachment ________________________________________
Removing Dome _______________________________________________
Maintenance
Inserting Or Replacing Batteries ________________________________
Recomended Replacement Periods _____________________________
Replacing O-ring _______________________________________________
Replacing Moisture Absorbing Pack ____________________________
Cleaning Dome _______________________________________________
Preventing Fogging On Dome ___________________________________
After Water Care ______________________________________________
Troubleshooting ________________________________________________
Specications _________________________________________________
Warranty ______________________________________________________
AquaLens is meant for depths no greater than 10 meters from the
water surface. Do not go beyond this depth due to limitation as opera-
tional safety is not tested and rated for such depths.
Secure all cables on board to prevent tripping hazards.
Do not submerge cable connector plugs, let them get wet or handle
them with wet hands.
Assure cable is properly secured to pole with adapter or straps before
use. AquaLens will sink if not properly secured.
Inspect AquaLens prior to use. If there is any sign of water inside the
camera or housing unit or other damage, do not use. Send AquaLens
to Aquabotix for service.
Do not attempt to dislodge or pry foreign objects from AquaLens. Send
AquaLens to Aquabotix for service.
Additional Restrictions On Use
AquaLens is meant for operation by adults over 18 years of age only.
Keep AquaLens out of the reach of children and supervise children and
pets when AquaLens is in operation.
Do not use AquaLens in rain, rough sea conditions and/or storms.
Do not use AquaLens while underwater machinery is in operation.
Do not touch AquaLens to underwater marine growth. Keep AquaLens
clear of all underwater objects.
Do not expose AquaLens to high temperatures above 40
0
Celsius /
104
0
Fahrenheit; avoid direct sunlight.
Use AquaLens in the recommended operating water temperature range
of 2
0
Celsius / 35
0
Fahrenheit to 32
0
Celsius / 89
0
Fahrenheit.
Dropping AquaLens or subjecting it to strong force may damage the
device and its watertight dome. Handle with care.
2Legal Disclaimer
Failure to follow these important safety instructions and the
detailed assembly and use instrucitons of this manual will void your
limited warranty from Aquabotix and may result in serious injury or
death. Aquabotix disclaims all liability arising from or caused by the
failure to assemble and use AquaLens in accordance with this
manual, including all important safety intructions.
3Legal Disclaimer
4Overview
LED lighting
video camera
standard 15 ft. cable
(optional longer length available)
anti-fogging technology
battery compartment
Built in connection
standard attacher
+ universal pole strap
Universal t to any pole
Viewing sphere
video out (composite)
(attach to belt)
(attach to forearm)
+ 12 VDC connector
3.5” LCD screen
arm band
Pole Attachment (prefered method)
If using a boat hook with threaded end:
a) Thread the angular adapter into the hole on the back of the
viewing sphere. Be sure to align the angular adapter vertically with
the camera.
b) Thread your boat hook into the angular adapter.
5AquaLens Assembly
a
b
Topside Box Connections
a) Attach the camera connecter cable to the topside box.
6AquaLens Assembly
a b
LCD Screen Attachment
Attach your forearm strap to the LCD screen. Turn the AquaLens on
with or without LED lighting, using the knob on the topside box. You’re
now ready to take a look at the underwater world!
Removing Dome
To remove dome, turn counter clockwise and remove. Use caution
when handling your dome to prevent scratches and to protect clarity.
Use caution when handling O-ring to be sure the area remains clean to
ensure a water tight seal.
7AquaLens Assembly
Batteries
a) Remove dome, turning counterclockwise. Use caution when handling
your dome to prevent scratches and to protect clarity. Use caution
when handling O-ring to be sure the area remains clean to ensure a
water tight seal.
b) With viewing sphere facing you, loosen, not remove, both screws
with your ngers.
c) Swivel battery access plate to get to battery pack.
d) Disconnect the battery pack, using the battery electrical snap.
e) Insert eight (8) AA batteries (not supplied).
Reconnect the battery pack, using the battery electrical snap. Swivel
battery access plate to cover battery pack. Tighten both screws on the
access plate with your ngers. Re-attach dome by lining up the grooves
and turning clockwise until it locks. Use caution when handling O-ring to
be sure the area remains clean to ensure a water tight seal.
b
c
d
a
e
8AquaLens Assembly
Recommended Replacement Periods
1. O-ring: Every 6 months.
2. Moisture absorbing pack (pg.10): Every 6 months.
To purchase these from Aquabotix, visit our online store---accessed
through our website at http://www.aquabotix.com/categories.php.
Replacing O-ring
1. Remove dome, turning counter clockwise.
2. To remove O-ring, use an O-ring removal tool or something at that
can get it out, such as a at head screwdriver or tweezers.
3. Remove replacement O-ring from package. Inspect for cracks
and tears.
4. Lubricate O-ring with an O-ring lubricant, found at most hardware stores.
5. Insert O-ring. Use caution when handling O-ring to be sure the area
remains clean to ensure a water tight seal.
6. Re-attach dome by lining up the grooves and turning clockwise until
it locks.
9
Maintenance
Replacing Moisture Absorbing Pack
1. Remove dome, turning counter clockwise. Use caution when handling
O-ring to be sure the area remains clean to ensure a water tight seal.
2. Pull off black cap.
3. Moisture absorbing pack will be exposed.
4. Take out moisture absorbing pack and replace.
5. Re-attach black cap.
6. Re-attach dome by lining up the grooves and turning clockwise until it
locks. Use caution when handling O-ring to be sure the area remains
clean to ensure a water tight seal.
Cleaning Dome
Using an acrylic glass cleaner, spray onto surface of dome and rub in
with a microber cloth.
Preventing Fogging On Dome
1. Remove dome, turning counter clockwise.
Use caution when handling O-ring to be sure the area remains clean to
ensure a water tight seal.
2. Spray a small amount of anti-fogging spray on the inside surface of dome.
3. Wipe area with a small cloth until surface is clear.
4. Re-apply as required.
After Water Care
1. Rinse AquaLens with fresh water.
2. Wipe down, using a microber lens cleaning cloth.
3. Safely store AquaLens---cover dome to protect from scratches.
10
Maintenance
b
d
Troubleshooting
LCD screen not working:
- Ensure power switch is in the ON position.
- If lights are on, but LCD screen is off, make sure LCD screen cable
is attached.
- If LCD screen is ickering, replace the batteries.
If AquaLens is leaking:
- Replace the O-ring. Find these instructions in the Table of Contents.
Specications
Weight - 3 lbs.
Diameter - 5 in.
LCD screen
Size: 3.5 in TFT LCD (ratio 4:3)
Resolutioness: 960 X 240 pixels
Camera
Total resolution: 640 X 480 pixels
LED lighting
Mounting straps
Boat hook angular adapter
Depth (cable dependent)
Standard: 15 ft. cable
Optional: 30 ft. or 50 ft. cable
Battery run time
Standard: 10 hours (8 AA batteries required)
Optional: Rechargeable batteries and charger
DC adapter continuous power
Operation voltage - 9.6 to 12 VDC
11 Troubleshooting & Specications
Aquabotix's AquaLens One Year Limited Warranty Certicate
Aquabotix warrants that, under normal use and service, the AquaLens
will be free from defects in material and workmanship for one year from
the date of purchase by the original purchaser.
If Aquabotix receives, during the applicable warranty period, notice of
defect in any product which is covered by Aquabotix's warranty, Aquabo-
tix shall either replace or repair the product at Aquabotix's discretion.
If Aquabotix is unable to repair or replace, as applicable, a defective
product which is covered by Aquabotix's warranty, Aquabotix shall, within
a reasonable time after being notied about the defect, refund the full
purchase price of the product.
Aquabotix shall have no obligation to repair, replace or refund the
purchase or product until the customer submits an RMA form and
returns the defective product to Aquabotix.
Warranty does not cover the following: damage caused by abuse or
misuse, improper maintenance, incorrect assembly, accidental damage,
or damage due to incorrect power connection as described in the user
manual. Consumable items including o-rings, moisture absorbing packs,
LED lights and batteries are specically excluded from the warranty.
Items subject to normal wear and tear include, but are not limited to,
the lens and the outer shell which are only covered for defects in work-
manship or materials.
Claims for damage, shortage or errors in shipping must be reported
within three (3) days following delivery to the customer. Aquabotix is not
responsible for returned items lost or damaged during shipping.
A copy of the dated receipt or bill of sale from the original end user
purchase is required to determine coverage.
This limited warranty gives you specic legal rights, and you may also
have other rights which vary from state to state.
For further information contact Aquabotix at:
617.419.5883
12 Warranty
Aquabotix Technology Corporation
1082 Davol St (L102)
Fall River, MA 02720
www.aquabotix.com
Innovation for the Underwater World
Table of contents
