Aquavista 21-K822-AVD User manual

1
HIGH-ARC KITCHEN FAUCET WITH
OPTIONAL SIDE SPRAY
21-K822-AVD – Polished chrome finish
21-K822- AV-BND – Brushed nickel finish
PACKAGE AND HARDWARE CONTENTS AD
NSF/ANSI 61
A
PART DESCRIPTION QUANTITY
C
D
A
B
E
F
G
A Faucet body 1
B Hose connection cap 1
C Side spray assembly 1
D Side spray support 1
E Side spray mounting nut 1
F Mounting nut 2
G Putty plate 1
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water supply
lines.
CAUTION
• If you solder the joints during installation, the seats, cartridges, and washers
must be removed before using a flame or the warranty will be voided on
these parts.
• Cover the drain to avoid losing parts.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package and hardware contents list. If any part is missing or damaged, do
not attempt to assemble the product. Contact customer service for replacement
parts.
Estimated AssemblyTime: 30 minutes
Tools required for assembly (not included): adjustable wrenches, groove joint
pliers, pipe wrench, Phillips screwdriver, supply lines, thread seal tape, silicone.
Installation may vary depending on how the previous faucet was installed.
Supplies necessary for the installation of the faucet are not all included;
however, they are available wherever plumbing supplies are sold.
Prior to beginning installation, turn off the hot and cold water lines, then turn
on the old faucet to release built-up pressure.When installing the new faucet,
hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections
that are too tight will reduce the integrity of the system.
Need Help? Please call our toll-free line at [phone] (7:30 a.m. to 4:30 p.m. CST) for additional assistance or service.
11-25-2019Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • HomewerksWW.com

2
HomewerksWW.com
PRODUCT SPECIFICATIONS
Max. Flow Rate: 1.8 GPM (6,81LPM) at 60 PSI Ceramic cartridges
ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
NSF 61-9
Polished chrome or brushed nickel finish Total weight of item: 2.05 lbs.
ASSEMBLY INSTRUCTIONS
1. Turn off water at the supply valve
under the sink or at the main water
supply. Disconnect the supply lines to
the faucet and remove the old faucet.
Clean and dry the surface area
where the new faucet will be
mounted.
15. To connect the water supply, use
1/2 in. IPS faucet supply lines (5.1)
or coupling nuts (5.2) with 3/8 in.
O.D. ball-nose risers (5.3).These
parts are not included.Wrap
thread seal tape around each
faucet shank (5.4) in a clockwise
direction. NOTE: When making
water line connections, hand
tighten with a wrench. Do NOT
overtighten.
5
2. Apply a thin bead of silicone
sealant to the putty plate (G) on
the underside of the faucet body (A).
Carefully slide the faucet shanks (2.1)
into the first and third sink holes
(2.2) from the left. Position the
faucet as desired. From underneath
the sink, thread the mounting nuts
(F) onto the shanks (2.1) on the
faucet body (A) and hand tighten.
Do not overtighten.
A
G
2
.1
2.2
F
26. After installation is complete,
remove the aerator (6.1) from the
spout (6.2) of the faucet body (A).
Turn on the water supply and allow
both the hot and cold water to run
for at least one minute.This flushes
away any debris that could cause
damage to the internal parts.While
the water is running, check for
leaks. Retighten any connections if
necessary, but do not overtighten.
6.1
A
6.2
6
3. Optional side spray installation:
Insert the side spray support (D)
through the far right hole on the
sink (3.1). From underneath the
sink, thread the side spray mounting
nut (E) onto the side spray support
(D) and hand tighten.
3.1
D
E
3
4. Insert the hose from the side spray
assembly (C) down through the spray
support (D) and sink (4.1) until the
spray head (4.2) rests in the top of
the spray support (D).
Underneath the sink, remove the
hose connection cap (B) from the
faucet body (A). Attach the side
spray assembly (C) hose to the hose
connection (4.3) at the bottom of
the faucet body (A) by tightening the
swivel nut (4.4) by hand, then use
pliers (not included) for 1/4 extra
turn. Be careful not to twist the hose
or overtighten the swivel nut (4.4).
A
4.2
D
C
4.4
4.
B
3
4.1
4

3
HomewerksWW.com
OPERATING INSTRUCTIONS
The lever handles control the flow of hot and cold water to the faucet.
Rotate the right handle forward for cold water. Rotate the left handle forward for hot water. Moving the handles forward opens the cartridges and causes water to flow
from the spout.The degree of handle opening determines the volume of water flow. Returning the handles to the original position stops the flow of water.
CARE AND MAINTENANCE
Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the finish and void your warranty.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Faucet leaks underneath handle. Bonnet has come loose or O-ring on cartridge
is dirty or twisted.
1. Move the handle to the OFF position. Unscrew the handle screw and remove
the handle.
2.Tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON
position.The leak should stop draining out from around the cartridge stem.
3. If the leak does not stop, shut off the water supply. Remove the bonnet by
turning it counterclockwise. Lift out the cartridge valve. Inspect the larger
O-ring on the cartridge bonnet and the smaller O-ring on the cartridge stem.
Remove any debris from the O-rings. If either O-ring is twisted, straighten it. If
either O-ring is damaged, replace the cartridge by calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on the
two sides of the cartridge bonnet fit into the grooves on the two sides of the
faucet body.Tightly screw the bonnet onto the faucet body.
5. Reinstall the handle.
Water does not completely
shut off.
Rubber valve seat is dirty, stuck, or broken. 1. Shut off the water supply.
2. Remove the handle from the faucet body. Loosen the bonnet by turning it
counterclockwise. Lift out the cartridge assembly.
3. Inspect the rubber valve seat in the faucet body. If there is debris or brass
scrap on the surface of the seat, remove it. If the rubber seat is stuck tightly in the
water inlet hole, push it gently with a fingertip so it moves up and down
smoothly.The spring (smaller end up) must be placed back underneath the valve
seat. If the rubber valve seat is worn out or broken, replace the cartridge by
calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on the two
sides of the cartridge bonnet fit into the grooves on the two sides of the faucet
body.Tightly screw the bonnet onto the faucet body.
5. Reinstall the handle.
Faucet leaks around aerator. The aerator is incorrectly fitted, dirty, or
small parts inside the aerator are improperly
installed.
1. Remove the aerator from the spout by turning it clockwise. Inspect the black
rubber packing inside the aerator.The rubber packing should be flat.
2. Screw the aerator back onto the spout and tighten.
Faucet has an improper water
pattern.
The aerator is dirty or small parts inside the
aerator are improperly installed.
1. Remove the aerator from the spout by turning it clockwise.
2. Gently flush the small parts inside the aerator to clear away any debris.
3. Reinstall the small parts as shown in the replacement parts exploded diagram.
Metal screens must be flat and plastic supporter must be straight.
4. Screw the aerator back onto the spout and tighten.

4
HomewerksWW.com
ROUGH-IN
8"
13-3/8"
11-1/2"
1/2"-14NPSM-2A
2"
5-7/8"
2-1/4"
6-1/2"
8"
9-3/4"
1-1/8"
REPLACEMENT PARTS
For replacement parts, call our customer service department at [phone], 7:30 am - 4:30 pm, CST, Monday - Friday.
PART DESCRIPTION PART #
8
1
2
4
3
5
6
7
21-K822-AVD 21-K822-AV-BND
1Handle RP03007AVD RP03007BND
2Bonnet RP03008 RP03008
3Ceramic cartridge - hot RP03009 RP03009
4Ceramic cartridge - cold RP03010 RP03010
5Aerator assembly RP03014AVD RP03014BND
6Putty plate RP03011 RP03011
7Mounting nut RP03012 RP03012
8Side spray assembly RP03015AVD RP03015BND
LIMITED LIFETIME WARRANTY
The distributor warrants to the original consumer purchaser this product to be
free from defects in material and workmanship under normal use in residential
applications.At its option, the Company will provide repair parts or replace
defective product when the product is used in accordance with the manufacturer’s
specifications.
Use of mild abrasive, abrasive or chemical cleaners may damage the finish of the
faucet.We recommend cleaning your faucet with a soft cloth, moistened with
water. Damage resulting from the use of abrasive or chemical cleaners SHALL
VOID THIS WARRANTY.
This warranty is not applicable to any products or parts of products where
damage is caused by use of non-genuine parts; is due to installation error,
roduct misuse, negligence or faulty maintenance; or where the product is
not installed according to local building codes.
This warranty excludes labor charges or damage incurred during installation,
repair or replacement, and any indirect, incidental or consequential damages,
losses, injury or costs of any nature.This warranty is in lieu of and excludes
all other warranties, conditions and guarantees, whether expressed or implied,
including without restriction those of merchantability or fitness of use.
Liability under this warranty will not exceed the purchase price for the
product claimed to be defective by the original consumer purchaser. Some
states or provinces do not allow the exclusion or limitation of consequential
damages so the above limitations or exclusions may not apply.This warranty
gives you specific legal rights and you may also have other rights which vary
from state to state, or province to province.
Inquiries regarding warranty claims can be directed to [phone],
7:30 a.m. to 4:30 p.m., CST, Monday - Friday.