Arconic Huck Powerig 940 User manual

Instruction Manual
940
Hydraulic Powerig®
August 10, 2017
HK496
Makers of Huck®, Marson®, Recoil®
Brand Fasteners, Tools & Accessories
Serial Number Notice
2
Safety Instructions
3
Description
4
Principle of Operation
4
Preparation for Use
4
Specications
5
Checking and Adjusting
Pressures
5
Operation
5
Maintenance
6
Components Drawings
7-10
Options and Accessories
11
Troubleshooting
11

2
940 Powerig® (HK496)
NOTICE
This manual applies to 940
serial number 3927 and above.
For any other serial numbers, please contact a Huck customer service representa-
tive.

3
940 Powerig® (HK496)
1. Ahalfhourlonghands-ontrainingsessionwithqualied
personnel is recommended before using Huck equipment.
2. Huck equipment must be maintained in a safe working
condition at all times. Tools and hoses should be inspected
at the beginning of each shift/day for damage or wear. Any
repairshouldbedonebyaqualiedrepairmantrainedon
Huck procedures.
3. Repairman and Operator must read manual prior to using
equipment. Warning and Caution stickers/labels supplied
with equipment must be understood before connecting
equipment to any primary power supply. As applicable, each
ofthesectionsinthismanualhavespecicsafetyandother
information.
4. ReadMSDSSpecicationsbeforeservicingthetool.MSDS
Specicationsareavailablefromtheproductmanufactureror
your Huck representative.
5. When repairing or operating Huck installation equipment,
always wear approved eye protection. Where applicable,
refer to ANSI Z87.1 - 2003
6. Only genuine Huck parts shall be used for replacements or
spares. Use of any other parts can result in tooling damage
or personal injury.
7. Ifapartafxedwithwarninglabelsisreplaced,orlabels
are missing or damaged, the end user is responsible for
replacement. Refer to assembly drawing and parts list for
replacement part number and proper placement.
8. Disconnect primary power source before performing
maintenance on Huck equipment or changing Nose
Assembly.
9. Tools and hoses should be inspected for leaks at the
beginning of each shift/day. If any equipment shows signs of
damage, wear, or leakage, do not connect it to the primary
power supply.
10. Mounting hardware should be checked at the beginning of
each shift/day.
11. Make sure proper power source is used at all times.
12. Release tool trigger if power supply is interrupted.
13.Toolsarenottobeusedinanexplosiveenvironmentunless
specicallydesignedtodoso.
14.Neverremoveanysafetyguardsorpintaildeectors.
15.Whereapplicable,ensuredeectororpintailcollectoris
installed and operating prior to use.
16. Never install a fastener in free air. Personal injury from
fastener ejecting may occur.
17. Where applicable, always clear spent pintail out of nose
assemblybeforeinstallingthenextfastener.
18. There is possibility of forcible ejection of pintails or spent
mandrels from front of tool.
19. Check clearance between trigger and work piece to ensure
there is no pinch point when tool is activated. Remote
triggers are available for hydraulic tooling if pinch point is
unavoidable.
20. Unsuitable postures may not allow counteracting of normal
expectedmovementoftool.
21. Do not abuse tool by dropping or using it as a hammer.
Never use hydraulic or air lines as a handle or to bend or pry
the tool. Reasonable care of installation tools by operators is
animportantfactorinmaintainingtoolefciency,eliminating
downtime, and in preventing an accident which may cause
severe personal injury.
22. Never place hands between nose assembly and work piece.
Keep hands clear from front of tool.
23. There is a risk of crushing if tool is cycled without Nose
Assembly installed.
24. Tools with ejector rods should never be cycled with out nose
assembly installed.
25. When two piece lock bolts are being used always make sure
the collar orientation is correct. See fastener data sheet for
correct positioning.
26. Tool is only to be used as stated in this manual. Any other
use is prohibited.
27. There is a risk of whipping compressed air hose if tool is
pneudraulic or pneumatic.
28. Release the trigger in case of failure of air supply or hydraulic
supply.
29.Useonlyuidsorlubricantsrecommended.
30. Disposal instruction: Disassemble and recycle steel, aluminum
andplasticparts,anddrainanddisposeofhydraulicuidin
accordance with local lawful and safe practices.
31. Iftoolisxedtoasuspensiondevice,ensurethatthedevice
is secure prior to operating the tool.
NOTE: Where the following trade names are used in this manual:
DEXRON is a registered trademark of General Motors Corporation.
Loctite is a registered trademark of Henkel Corporation, U.S.A.
LUBRIPLATE is a registered trademark of Fiske Brothers Rening Co.
MERCON is a registered trademark of Ford Motor Corp.
Never-Seez is a registered trademark of Bostik, Inc.
Quintolubric is a registered trademark of Quaker Chemical Corp.
Slic-tite is a registered trademark of LA-CO Industries, Inc.
Teon is a registered trademark of E. I. du Pont de Nemours and
Company.
Threadmate is a registered trademark of Parker Intangibles LLC.
TRUARC is a trademark of TRUARC Co. LLC.
Vibra-Tite is a registered trademark of ND Industries, Inc. USA.
Safety Instructions
GLOSSARY OF TERMS AND SYMBOLS:
- Product complies with requirements set forth
by the relevant European directives.
- Read manual prior to using this equipment.
- Eye protection is required while using this
equipment.
- Hearing protection is required while using this
equipment.
Notes: are reminders of required procedures.
Bold, Italic type, and underline:emphasizeaspecic
instruction.
WARNINGS: Must be understood to avoid
severe personal injury.
CAUTIONS: Show conditions that will damage
equipment or structure.

4
940 Powerig® (HK496)
CAUTION
PULL
PRESSURE
CAUTION
RETURN
PRESSURE
115V AC
Electrical
Enclosure
Pilot
Valve Quick
Disconnect
Coupler
Quick
Disconnect
Coupler
Four-Way
Directional
Valve
Reservoir
Power
Cord
High Pressure
Relief Valve
Motor
and
Pump
}
Figure 1
Figures 1 & 5
Model 940 Powerig®is a portable, electrically operated
power source designed to operate all Huck hydraulic
installationequipmentexcludingHuck-Spin®tools. It
operates on 115 volt AC, 50-60 Hz, one-phase electrical
power. The power cord is a 10/3 SJTO cord with a NEMA
L5-30 plug. The motor is rated at 115V, 50/60Hertz,
25A. An electrical enclosure contains a motor contact,
transformer, relay and circuit breaker. Hydraulic pressure
occurs by a two-stage, gear-piston pump driven by a 1 1/8
horsepoweruniversalelectricmotor.Pressurizeduidis
directed by a four-way directional valve to either the PULL
or RETURN port of the installation equipment. The four-
way directional valve is operated by a 24 volt AC control
circuit. The high pressure relief valve controls PULL
pressure(maximumpressureoftheunit)andisadjustable
by the operator. An internal relief valve is preset at
the factory to protect the Operator and equipment.
The internal relief is not adjustable by the operator. A
pressure switch controls RETURN pressure and turns off
the Powerig at the end of an installation cycle. Pressures
are adjustable to match Huck equipment being used. See
applicable tool instruction manual for pressure settings for
otherHuckinstallationequipment.Hydraulicuidisstored
in the reservoir which also serves as the base. Remove
thellercap/dipsticktocheckuidlevelandtoadduid.
Hydraulic quick disconnect couplers are furnished for
connecting hoses from installation equipment.
Description
FIGURE 2
Pressureswitch(PS)contactsarenormallyclosed.
Increasing pressure opens contacts. When the
tool trigger switch is depressed, 24 volts AC is
applied between relay terminals CR13 and CR14
activating the relay coil and closing two sets
of contacts, CR9-CR5 and CR12-CRS. Closing
contacts CR9-CR5 starts the motor. Closing
contacts CR12-CR8 activates the solenoid coil
of the pilot valve. The pilot valve shifts the
directional valve spools.
PressurizeduidisdirectedtothePULLpressure
port of the installation equipment. When the tool
trigger switch is released, the relay contacts open.
The solenoid coil is deactivated and the spring
return of the pilot valve shifts the directional
valvespools.Pressurizeduidisdirectedto
the RETURN pressure port of the installation
equipment.
The motor contact is held closed until the preset
RETURN pressure is reached and pressure switch
(PS)contactsopen.Themotorturnsoff,the
pressure drops, and pressure switch returns to the
closed(normal)position.
SERVICE
Introduction of foreign material into Hydraulic Unit will result
in poor performance and down time for repair. To avoid this:
Cleantheareaaroundthellercapbeforeaddinghydraulic
uid,alwaysuseacleanfunnelwithalter,keepquick-
disconnectcouplerscleanbykeepingthemofftheoor,ans
wipe off quick-disconnect couplers before connecting them.
BEFORE USE
Fillthereservoirwithhydraulicuid,approximately2.6
gallons(9.8liters),untiltheuidlevelisbetweenthegrooves
of the dipstick.
The 940 Powerig is shipped without hydraulic uid.
Principle of Operation
Preparation for Use





  


















 
 
 





 










 



 

Figure 2
Electrical Schematic Diagram

5
940 Powerig® (HK496)
CSA-US CERTIFIED
940 Powerigs are intended for use in indoor factory
environments, and if used outdoors they must be
protected from the elements.
WIDTH:16.1inches(40.9cm)
LENGTH:13.9inches(35.4cm)
HEIGHT:18.5inches(47cm)
WEIGHT:66pounds(30kg)(withemptyreservoir)
ELECTRICAL SYSTEM:115VAC(25A),50/60hz,singlephase
CONTROL SYSTEM: Solenoid operated directional valve, 24V
MOTOR: 12000 RPM, 1-1/8 HP, 25 amps. nominal
PUMP: 2-stage, gear-piston type, 70 in3/min @5,000 psi out
pressure(Outputpressureadjustableto10,000psi)
RESERVOIR CAPACITY: 2.6gallons(9.8liters)
PRESSURE SETTING AS SHIPPED:
RETURN:2,200-2,400psi(15,200-16,500kPa)
PULL:5,400-5,700psi(37,200-39,300kPa)
Minimum Operating Temperature (ambient):0°(18°C)
Maximum Hydraulic Fluid Temperature:150°F(65°C)
HYDRAULIC FLUID: HydraulicuidshallmeetDEXRON®
III,DEXRONVI,MERCON,AllisonC-4orequivalentATF
specications.
Fireresistantuidmaybeusedifitisanesterbaseduid
suchasQuintolubricHFDorequivalent.Waterbaseduid
shall NOT be used as serious damage to equipment will
occur.
Specications
CHECKING PRESSURES
WARNINGS above must be understood. Check PULL and
RETURN pressures before use, before troubleshooting, and
afteroverhauling.Seepressuresgiveninthespecictool
instruction manual. For checking pressures, use T-124833CE
Pressure Gauge and its instruction manual.
ADJUSTING PRESSURES
NOTE: Using gauge T-124833CE, set pressures according to
thespecicinstallationequipmentmanual.
ADJUSTING PULL PRESSURE
NOTE: PULL pressure is the maximum Powerig®pressure.
Do not exceed the pressure rating of the installation
equipment. See the installation equipment manual for
pressure rating.
1. Loosen the jam nut of the high pressure relief valve.
2. Turn the adjusting screw clockwise to increase PULL
pressure OR counterclockwise to decrease PULL pressure.
3. Tighten the jam nut after PULL pressure has been
adjusted.
4. Check PULL pressure. Follow instructions in the
appropriate section of this manual.
ADJUSTING RETURN PRESSURE
1. Loosen the jam nut on pressure switch.
2. Turn the adjusting screw clockwise to increase RETURN
pressure OR counterclockwise to decrease RETURN
pressure.
3. Tighten the jam nut on pressure switch after return
pressure has been adjusted.
4. Check RETURN pressure. Follow instructions in the
appropriate section of this manual.
Checking and Adjusting Pressures
WARNINGS:
Maximum PULL pressure is 8400 psi. Refer to
specic tool instruction manual for PULL and
RETURN pressures. Severe personal injury may
occur if excessive pressures cause violent failure
of equipment. Higher than normal pressures will
also cause premature wear of equipment.
If recommended maximum pressure is exceeded,
violent failure of fastening system may occur.
This may cause severe personal injury.
Operation
Before each use:
1. Checktheuidlevelinthereservoirandaddhydraulic
uidasrequired.
2. Inspect hoses for damage and wear. If hoses show wear
thathasremovedmorethanthesurfacetexture,they
must be replaced.
3. Check the entire system and repair any leaks.
4. Checkelectricalcordandextensionforabrasionand
replace as required.
Be sure that the hose from PULL PRESSURE on the
control panel runs to the port stamped with a letter ‘P’
on the tool, and the hose from RETURN PRESSURE on the
control panel runs to the port stamped with letter ‘R’ on
the tool.
Plug the control cable from the tool into the two-prong
socket on the POWERIG Hydraulic Unit control panel.
Depress the tool trigger switch and let the POWERIG
HydraulicUnitoperateforafewminutestocirculateuid
and remove air from the system.
Attach a nose assembly to the installation equipment.
Fasteners may now be installed. Follow instructions in the
tool manual.
Operating Tools:
Plug the power cord into a grounded wall outlet.
Check pressures and adjust as necessary. See the appropriate
sections in this manual. WARNINGS must be understood
before checking pressures. Connect hydraulic hoses from a
HUCK hydraulic tool to the Powerig.

6
940 Powerig® (HK496)
Maintenance
PREVENTIVE MAINTENANCE
An effective preventive maintenance program includes
scheduled inspections to detect and correct minor troubles.
Perform the following steps monthly during normal use:
· Ensuresecurerofhydraulicandelectricalttings.
· Inspect hoses for signs of damage. Replace hoses if
abrasionisdeeperthanthesurfacetexture.
· Rotate hoses end-for-end to equalize wear and fatigue.
· Inspect during operation to detect any abnormal heating,
vibration or leakage.
· Inspecthydraulicuid.Ifcontamination(particles,water,
sludge,etc.)isdetected,cleanreservoirandreplaceuid.
· Cleanexteriorsurfaces.
· Check supply voltage. Do not operate the Powerig®
Hydraulic Unit if the line voltage is more than 5 percent
above or below 115 Volts.
· Checkmotorbrushes.Seegurebelow.
SPARE PARTS
The quantity of spare parts that should be kept on hand
varies with the application and number of the Powerig
Hydraulic Units in service. Parts that should be available to
the service technician are: Pump-to-Motor Coupling, Relay,
Transformer, Pilot Valve, and Motor Brushes. See Options
and Accessories section of this manual for part numbers.
DIRECTIONAL VALVE OVERHAUL
If overhaul of the directional valve is necessary, a valve repair
kit that has the spools, cartridges & poppets is 129437,
is available for purchase, and should be kept on hand. To
rebuild valve, follow instructions included with kit.
PUMP OVERHAUL
If pump requires overhaul return it, or the complete unit, to
the nearest repair facility shown on the inside back cover.
REPLACING PUMP-TO-MOTOR COUPLING
Pump-to-motor coupling can be replaced by removing four
socket cap screws holding the motor housing to the cover
plate and lifting the motor to one side. Lift out the original
coupling with needle-nose pliers. Drop in the new coupling,
align the slots and reassemble motor to cover plate.
INTERNAL ADJUSTMENT OF PRESSURE SWITCH
1. Remove the top cover of the switch.
2. Loosen two screws located in bottom of switch housing.
3. Place a 0.20-inch-thick shim between the spring retainer
and the platen.
4. Loosen the set screw on the spring retainer until it
contacts shim.
5. Lock the spring retainer in place with the set screw.
6. Slide the switch mounting bracket toward the switch
button until it contacts the platen surface.
7. Secure with two screws located in the middle of the
bottom cover.
8. Connect a volt/ohm meter to the electrical cord.
9. Tighten the switch adjustment screw against the switch
mounting bracket until the switch button contacts the
platen and actuates. The volt/ohm meter will react when
the button actuates. A click can be heard.
10. Continue tightening the switch adjustment screw 1/8 of a
turn after the switch button actuates.
11. Replace the top cover of the switch.
CHECKING MOTOR BRUSHES
Checking motor brushes frequently helps to prevent premature failure
of the armature. To check the brushes:
1. Remove the metal brush cover plates.
2. Unscrew the plastic brush holder caps. Note: Springs on the
brushes will push on the caps. Hold the caps as they are
loosened.
3. Remove brush assemblies.
4. Clean copper commutators on the armature with a pencil eraser.
5. Clean out spaces between connections with a plastic tool. If
commutator is damaged or worn, replace armature with Armature/
Field Kit, which is included in the Motor Service Kit. See Options
and Accessories section of this manual for part numbers.
6. Measure the length of the carbon brush, and replace both brushes
if either one is 1/4 inch or less in length.
7. Install brush assemblies, brush holder cups, and metal brush cover
plates.
(Spring)
Brush
Brush
Holder Cap
Brush
Holder
Replace both brushes
ifeitheroneislessthan
1/4 inch in length.
Motor
Shell
SERVICE PERIOD ACTION
BEFORE
EACH
USE
EVERY
50
HOURS
EVERY
100
HOURS
EVERY
200
HOURS
Hydraulic Hose Fittings Check-Clean •
Electrical Connections Check •
Hydraulic Fluid Level, Fill Cap Tight Check •
Verify Pull & Return Pressure, Tighten
Adjustment Screw Jam Nuts Check •
Tighten Cover Plate Screws Check •
Tighten Screws on Engine Check •
Change Hydraulic Fluid, Clean Tank Change • (Notes 1and 2)
Check Motor Brushes Check •
Directional Valve Seals, Poppets & Seats Check • (Note 3)
ExternalReliefValveStem Check • (Note 4)
Notes:
1. Service more frequently
when used in dusty
areas.
2.Hydraulicuid:use
32AW (0°F - 70°F
ambient),46AW(30°F-
120°Fambient),orATF
(30°F-90°Fambient).
3. If poppets show wear,
use Huck Directional
Valve Kit to replace
poppets, seats & seals.
4. If valve stem shows
wear, replace with Huck
Valve Stem.

7
940 Powerig® (HK496)
Note:
This assembly is purchased
complete. The bill of material
listed is for reference and
replacement part purposes
only.




(10)




























(4)








with











(4)





Figure 4
111345 Pump, Motor, Valve Assembly

8
940 Powerig® (HK496)
506362 Contactor
110685 Female Base 508266
Strain
Relief
506365 Relay Socket 502767 Screw 502769 Screw
506366
Relay &
506393
Hold-down
Spring
506363
Circuit
Breaker
128187 Power
Cord Assy
(Includes Strain Relief 508266)
502783 Screw 500693 Lockwasher 500234 Hex Nut
590303 Schematic Sticker
506368 Enclosure Gasket
123479
Enclosure
507293
Transformer
500424
Screw (4)
502767
Screw (2)
502758 Screw (2)
590131
Sticker
(115V AC)
590131
Sticker
(Class 2
Circuit 30V)
123433
Enclosure
Panel
590134
Sticker
(24V AC)
501214 Screw (3)
590012 Nameplate 502992 Screw (4)
Motor Cord
502783
Screw (4)
Pressure Switch Solenoid
123432 Motor Gasket
506364
Strain
Relief
Figure 5
123490 Electrical Enclosure Assembly

9
940 Powerig® (HK496)
Electrical Schematic and Wiring Diagram

 
 





 




 

  





  

  

  



















   
     
  
     
       
 
 
  
     
Figure 6
Wire No. Color From To
1A red transformer lower right circuit breaker
1 red CR12 CR9 1 red circuit breaker MCL3 1 red MCL1 MCL3 1 red MCL3 CR9 2 white MCL2 transformer lower
left
2 white MC terminal MCL2 3 red MCT3 CR5 6 blue transformer upper left trigger 7 blue trigger CR14 8 blue transformer upper
right CR13

10
940 Powerig® (HK496)
508883Screw(4) Torque to 22 in/lbs
500192 LockWasher(4)
115766 Ball Bearing
NOTE 1
115767 Ball Bearing
NOTE 1
115764 Armature Note: CCW rotation viewed from shaft-end.
115785 Brush
HolderCap(2)
131338
Motor Base
131337 Motor
Baffle Plate
111415 Motor
Brush Set
(Set includes 2 brushes)
115784 Brush
Holder(2)
NOTE 2
A
A
131339 Motor Shell
508882 Setscrew(2)
500693 Toothed
LockWasher(2)
508884MachineScrew(2)
Do not Loctite these screws.
NOTES:
1. Press bearings into armature, and install as a unit into
the motor shell. Apply Loctite® 277 Threadlocker, or equivalent, between outer race and bore. Place motor in an upright position while Loctite cures.
2. Brush Holders must be installed with slot and dimple
facing the open end of the Motor Shell. Apply Loctite® 680™ Retaining Compound, or equivalent, between Brush Holder and bore.
3. Insert Flag Terminals into adjacent Brush Holders. 4. Line leads must be routed through the rectangular
opening in the Motor Shell.
VIEW A-A
.020 min. Typ.
.020 min. Typ.
.677-.702 (both sides)
NOTE 3
115768 Field Stator must be installed with part number and date visible through the opening of the Motor Shell
NOTE 4
111346_revE
111346 Motor
Figure 7

11
940 Powerig® (HK496)
Troubleshooting
1. Motor fails when tool switch is depressed:
 (a)Looseordefectivecontrolcordorconnectors.
 (b)Powersourcenotproperlyfused.
 (c)Defectivetoolswitch.
 (d)Loosewire(s).
 (e)Defectiverelay.
 (f)Incorrectpowersource.
 (g)Defectivemotorcontactor.
 (h)Defectivetransformer
2. Motor runs, but tool will not reciprocate:
 (a)Hosesnotcoupledproperly.
 (b)Hydraulicuidviscositynotproperorlevelislow.
 (c)Defectivepilotvalvesolenoidorcoil.
 (d)Unloadingvalvemissingintool.
 (e)Bindintoolornoseassembly.
 (f)Defectivedirectionalvalve.
 (g)Pumptomotorcouplingdamaged.
3. Pintail of fastener fails to break off:
 (a)PULLpressuresettoolow.
 (b)Wornordefectivehosecouplers.
 (c)Hydraulicuidviscositynotproperorlevelislow.
 (d)Hydraulicuidoverheated.
 (e)Wornordefectivedirectionalvalve.
 (f)Internalreliefvalvesettoolowordefective.
 (g)Wornordefectivepump.
4. Tool will not return when switch is released. (Tool will
notpushnoseassemblyoffswagedfastener.):
 (a)RETURNpressuresettoolow.
(b)Hosesnotcoupledproperly.
(c)Wornordefectivesolenoid.
 (d)Wornordefectivepilotvalve.
5. Motor fails to shut-off when installation cycle is
completed:
 (a)RETURNpressureswitchsettoohigh.
 (b)Hydraulicuidviscositynotproperorlevelislow.
 (c)Hydraulicuidoverheated.
 (d)Defectivelimitswitchinpressureswitchassembly.
6. Pump making noise throughout entire cycle:
 (a)Pumpiscavitating-uidlevelmaybeloworuid
viscosity too heavy.
 (b)Strainerisdirtyandclogged.
7. Tool operation slow; Entire cycle does occur:
 (a)Pumpiscavitating-uidlevelmaybeloworuid
viscosity is too heavy.
 (b)Strainerisdirtyandclogged.
 (c)Wornordefectivedirectionalvalve.
 (d)Wornordamagedpump.
 (e)Wornordefectivehydrauliccouplers.
Alwayscheckthesimplestpossiblecauseofmalfunctionrst.Forexample,blownfuse,trippedcircuitbreaker,
defective switch or control cord. Eliminate each possible cause until the defective circuit or part is located. Where
possible,substituteknowngoodpartsforsuspectedbadparts.Aqualiedelectricianshouldcheckoutthe
electrical system. Use this section as an aid in locating trouble and correcting it.
OPTIONS
940T-1 (SpecialVersionof940)
The 940T-1 is part of Huck’s revised aftermarket Truck
Kits, which contain different pressure installation tools.
This hydraulic unit will be shipped from the factory with
output pressures set as follows:
PULL: 5700-5800 psi RETURN: 4400-4600 psi
ACCESSORIES:
Auxiliary Switch and Control Cord 113056
Anauxiliaryswitchisavailableforusewhencheckingand
adjusting pressures and when troubleshooting.
Gauge T-124833CE
A “T” gauge is available for use when checking and
adjusting pressures, and troubleshooting.
Hose and Control Cord Kits of various lengths
Please contact your HUCK representative.
Directional Valve Kit 129437
Includes seals necessary to service Directional Valve
103596.
Rig Transport Dolly 129703
Heavy duty steel dolly for easy movement of powerig
throughout the work area.
Motor 111346
Motor and Pump Assembly 111345
Motor Service Kit 115770
includes:
Motor Brushes Set 111415
115V Armature 115764
Upper Bearing 115766
Lower Bearing 115767
115V Motor Field 115768
Brush Holder 115784
Brush Holder Cap 115785
Gasket 115786
Options & Accessories

12
940 Powerig® (HK496)
Record your own notes here.

13
940 Powerig® (HK496)
Limited Warranties
Limited Lifetime Warranty on BobTail® Tools:
Huck International, Inc. warrants to the original purchaser
that its BobTail® installation tools manufactured after
12/1/2016 shall be free from defects in materials and
workmanship for its useful lifetime. This warranty does
not cover special order / non-standard products, or part
failure due to normal wear, tool abuse or misapplication,
or user non-compliance with the service requirements and
conditions detailed in the product literature.
Two Year Limited Warranty on Installation Tools:
Huck International, Inc. warrants that its installation tools
and Powerigs®manufactured after 12/1/2016 shall be
free from defects in materials and workmanship for a
period of two years from date of purchase by the end
user. This warranty does not cover special order / non-
standard products, or part failure due to normal wear,
tool abuse or misapplication, or user non-compliance with
the service requirements and conditions detailed in the
product literature.
90 Day Limited Warranty on Nose Assemblies and
Accessories:
Huck International, Inc. warrants that its nose assemblies
and accessories shall be free from defects in materials
and workmanship for a period of 90 days from date of
purchase by the end user. This warranty does not cover
special clearance noses, or special order / non-standard
product, or part failure due to normal wear, abuse or
misapplication, or user non-compliance with the service
requirements and conditions detailed in the product
literature.
Useful lifetimeisdenedastheperiodoverwhichthe
productisexpectedtolastphysically,uptothepoint
when replacement is required due to either normal
in-service wear, or as part of a complete overhaul.
Determination is made on a case-by case basis upon
return of parts to Huck International, Inc. for evaluation.
Tooling, Part(s) and Other Items not manufactured by
Huck:
HUCK makes no warranty with respect to the tooling,
part(s),orotheritemsmanufacturedbythirdparties.
HUCKexpresslydisclaimsanywarrantyexpressed
or implied, as to the condition, design, operation,
merchantability,ortnessforuseofanytool,part(s),or
other items thereof not manufactured by HUCK. HUCK
shall not be liable for any loss or damage, directly or
indirectly,arisingfromtheuseofsuchtooling,part(s),
or other items or breach of warranty or for any claim for
incidental or consequential damages.
Huck shall not be liable for any loss or damage resulting
fromdelaysornon-fulllmentofordersowingtostrikes,
res,accidents,transportationcompaniesorforany
reason or reasons beyond the control of the Huck or its
suppliers.
Huck Installation Equipment:
Huck International, Inc. reserves the right to make
changesinspecicationsanddesignandtodiscontinue
models without notice.
Huck Installation Equipment should be serviced by trained
service technicians only.
Always give the serial number of the equipment when
corresponding or ordering service parts.
Complete repair facilities are maintained by Huck
International,Inc.Pleasecontactoneoftheofceslisted
below.
Eastern
One Corporate Drive Kingston, New York 12401-0250
Telephone(845)331-7300FAX(845)334-7333
Outside USA and Canada
Contact your nearest Huck International location (see
reverse).
In addition to the above repair facilities, there are
AuthorizedToolServiceCenters(ATSC’s)located
throughout the United States. These service centers offer
repair services, spare parts, Service Parts Kits, Service
Tool Kits and Nose Assemblies. Please contact your Huck
Representative or the nearest Huck International location
(seereverse)fortheATSCinyourarea.

Arconic Inc. (NYSE: ARNC) creates breakthrough products that
shape industries. Working in close partnership with our customers,
we solve complex engineering challenges to transform the way we
fly, drive, build and power.
Through the ingenuity of our people and cutting-edge advanced
manufacturing, we deliver these products at a quality and efficiency
that ensures customer success and shareholder value.
Arconic Fastening Systems and Rings world-wide locations:
AMERICAS
Kingston Operations
1 Corporate Drive
Kingston, NY 12401
800-278-4825
845-331-7300
FAX: [phone]
Carson Operations
900 Watson Center Rd.
Carson, CA 90745
800-421-1459
310-830-8200
FAX: [phone]
Waco Operations
PO Box 8117
8001 Imperial Drive
Waco, TX 76714-8117
800-388-4825
254-776-2000
FAX: [phone]
Tucson Operations
3724 East Columbia
Tucson, AZ 85714
800-234-4825
520-747-9898
FAX: [phone]
Acuña Operations
Hidalgo #120
Parque Industrial Amistad
26220 Acuña Coahuila
Mexico
FAX: [phone]
TELEX: 1173530 LUKSME
EUROPE
Telford Operations
Unit C, Stafford Park 7
Telford, Shropshire
England TF3 3BQ
01952-290011
FAX: [phone]
Us Operations
BP4
Clos D’Asseville
95450 Us par Vigny
France
33-1-30-27-9500
FAX: [phone]
AUSTRALIA
Melbourne Operations
11508 Centre Road
Clayton, Victoria
Australia 3168
03-764-5500
Toll Free: 008-335-030
FAX: [phone]








Huck is Forever, For the Long Haul, The Future
of Fastening Technology, The Future of Assembly
Technology, The Future of Tooling Technology,
and Tools of Productivity are service marks of
Huck International. Huck provides technical
assistance regarding the use and application of
Huck fasteners and tooling.
NOTICE: The information contained in this
publication is only for general guidance with
regard to properties of the products shown
and/or the means for selecting such products,
and is not intended to create any warranty,
express, implied, or statutory; all warranties are
contained only in Huck’s written quotations,
acknowledgments, and/or purchase orders. It
is recommended that the user secure specific,
up-to-date data and information regarding each
application and/or use of such products.
© 2017 Huck International, Inc. www.afsrhuck.net/us
1 Corporate Drive, Kingston, NY 12401 • Tel: [phone] • Fax: [phone]