AREA Sacagawea VK-1222 User manual

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
10’
10’
Plan View
Sacagawea - VK-1222 - General Layout & Instructions

© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Using You Set-up Instructions:
The Visionary Designs Set-up Instructions for Sacagawea displays are created
specifically for your configuration. They are laid out sequentially, including an
exploded view of the entire display and a logical series of detailed steps for
assembly. We encourage you to study the instructions before attempting to
assemble your exhibit.
THIS IS VERY IMPORTANT!
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in red).
Cleaning & Packing Your Display:
1) Use care when cleaning aluminum extrusions or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or counter tops, use mild cleansers and
a soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing materials. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Hex Key Tool Typical Connection Typical Connection
Most visionary design exhibits can
be assembled with the supplied Hex
Key Tool. Occasionally, a flat head
screwdriver may be required. Detail A: Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock and creates
a strong positive connection.
Numbered
Label
Detail B: Each extrusion contains a numbered label that
corresponds to set-up instructions. The label is located
within a groove of the extrusion (when possible). Visionary
Design labels contain Black numbers unless otherwise
specified.
Horizontal Connection
Detail C: A rectangular connection bar with plastic
T Knobs is inserted between two horizontal extrusions
joined end-to-end. Turn the knobs clockwise to tighten.
Base Plate Connection Vertical Connection Corner Connection
Detail D: Attach vertical extrusions to base
plates with supplied bolts inserted through
the hole in the plate. Be careful not to strip
the thread.
Detail E: A square connection bar with
plastic T Knobs is inserted between two
vertical extrusions joined end-to-end. Turn
the knobs clockwise to tighten.
Detail F: Plastic Star Knobs are
used to tighten locks where
horizontal extrusions connect with
vertical extrusions. Turn the knobs
clockwise to tighten. Turn counter-
clockwise to loosen, but do not
remove knob.
Do Not Overtighten.
Do Not Overtighten.
Do Not Overtighten.
Sacagawea - VK-1222 - General Layout & Instructions

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Backwall Assembly
Item
1
2a/2b
3a/3b
4a/4b
5a/5b
6a/6b
Description
Base Plate
42” Vertical Extrusion
42” Vertical Extrusion
45” Horizontal Extrusion
45” Horizontal Extrusion
2.5” Angle-Cut Vertical
Qty.
2
1/1
1/1
1/1
1/1
1/1
3b
6b Tighten setscrew
to secure
2.5”h Angle-Cut
Vertical Attachment
Back View of Backwall
5b
Insert connector into
groove of extrusion [3b].
Tighten setscrew
to secure.
*
Front View
indicates
location of connection
lock with knob.
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Connection Bar
a
Turn Knob Clockwise
to Tighten Lock
indicates location of
knobs on BACKSIDE of unit.
Do not over tighten Knobs
Knob
Knob
Horizontal Placement
Stopper
Set upper horizontal
bar atop stopper where
indicated on verticals Back View
a
b
b
1
1
2a
2b
3a
3b
4a
4b
5a
5b
Velcro:
Back/Bottom Edge
Veclro:
Back/Top Edge
Attach graphic
to velcro on back
of frame
6a
*
6b*
Steps:
1) Attach base plates [1] to lower verticals [2a,3a] with bolts.
2) Connect upper verticals [2b,3b] to lower verticals [2a,3a] with connection bars [b].
3) Connect horizontals [4a,4b] and [5a,5b] with connection bars [a].
4) Connect vertical assemblies [2a/2b,3a/3b] with horizontal assemblies [4a/4b,5a/5b] as shown.
5) Connect angled verticals [6a,6b] to upper verticals as shown.
6) Attach graphics to velcro on back side of frame.
Sacagawea - VK-1222 - General Layout & Instructions

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Knob
Wing Attachment
Keep A10 clamps
attached to verticals
Graphic
Screw
Cap
Standoff
Barrel
Slide connector on back of standoff
barrel into groove of extrusion
and twist to secure in place. Secure graphic
to standoffs using screw cap.
Graphic Attachment
7
8
9
Note: Curved extrusion
[10] and horizontal [11]
stay assembled for
shipping and packing.
10
10a
11
Screw
11a
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Wing Nut
Attach graphic
to velcro on back of
header frame
Item
7/8/9
10
10a
11
11a
Description
Header Frame
30.2” Curved Extrusion
Leg Support
12.184”w Horizontal Extrusion
Flange Plate
Qty.
1/1/1
1
1
1
1
Note: Header frame ships
and packs assembled
Steps:
1) Attach lights as indicated.
2) Attach assembled header frame and apply graphics as shown.
3) Attach assembled counter support [10/11] to vertical where indicated.
4) Attach support leg [10a] to counter support [10/11].
5) Attach flange plate [11a] to top of curved extrusion [10] as shown.
6) Attach counter top to support, see counter top attachment detail.
7) Attach wings toA10 clamps as shown.
8) Attach round sign to backwall frame as indicated.
Wing and Sign Attachment
Sacagawea - VK-1222 - General Layout & Instructions

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Case Packing Instruction
Setup Hardware
Lights
Graphic
(1) Backwall Components
Counter
Top
Base Plates
Backwall Counter
Support
Round Sign
Level 1 Level 2 Level 3
Wing Panels
Assembled Header
a3&3#snoisurtxE
a2&2#snoisurtxE
Horizontal extrusions #4a&4b abd 5a&5b
10a
Connection Bars A
Connection Bars B
Sacagawea - VK-1222 - General Layout & Instructions