AREBOS AR-HE-IW1010 User manual

User’s Manual –AREBOS Impact Wrench
1
Impact wrench
AR-HE-IW1010
Please follow all security measures in this user´s manual to ensure a secure use.
Thank you for trusting in AREBOS.

User’s Manual –AREBOS Impact Wrench
2
Please read and save these instructions. Read through this user’s manual carefully before using
product. Protect yourself and others by observing all safety information, warnings and cautions.
Failure to comply with instructions could result in personal injury and/or damage to product or
property. Please retain instructions for future reference.
Safety instructions
Explanation of the symbols
Warning! Read the safety instructions carefully. The
Failure to follow the safety precautions could result in serious injury or damage.
Keep the operating instructions in a safe place.
Warning! Wear safety glasses!
Warning! Wear ear protection!
Warning! Wear a dust mask.
This product has been tested and certified by TÜV Rheinland.
The symbol "GS" stands for tested safety. Products with
marked with this sign meet the requirements
of the German product safety law (ProdSG).
This product must not be disposed of with household waste!
By means of a CE marking, it can be recognized that a product complies with the
legal provisions of European legal norms and therefore may be traded within the
European Community.

User’s Manual –AREBOS Impact Wrench
3
General safety instructions
•Read all warnings and instructions. Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injuries have resulted.
•Save all warnings and instructions for future reference.
•When using power tools to protect against electrical shock, injury and fire the following basic
security measures to be observed. Read and follow these instructions before using the tool.
Keep in a safe place.
•Check the voltage on the nameplate voltage (volts)
•Keep your work area clean
•Cluttered areas and benches can cause accidents.
•Consider environmental factors.
•Install power tools to rain. Do not use power tools in damp or wet environments. Provide
good lighting. Use electric tools near flammable liquids or gases.
•Protect yourself from electric shock.
•Avoid body contact with grounded surfaces (eg pipes, radiators, stoves, refrigerators).
•Keep children away.
•Let other people do not touch the tool or cable, keep them away from your work area.
•Keep your tools safely.
•Unused tools should be stored in dry, securely, and the reach of children.
•Do not overload your tool.
•Do the job better and safer at the rate range.
•Use the right tool.
•Do not use accessories or attachments is too weak for heavy work. Do not use tools for
purposes and work for which they are intended (eg do not use a saw to chop down trees or
to cut branches).
•Wear suitable clothing. Do not wear loose clothing or jewelry, they can be caught in moving
parts. When working outdoors, wear rubber gloves and sturdy footwear. If you have long
hair, wear a hair net.
•Use safety glasses.
•Use a dust mask if cutting operation is dusty.
•Close to the dust extraction.
•When using the equipment with a dust extractor, ensure that it is correctly connected and
used according to regulations.
•Do not misuse the cord.
•Carry the tool by cord, use cord not the plug from the AC wall outlet, and protect the cable
from heat, oil and sharp edges.
•Secure the work piece.
Use to hold clamps or a vise to the workpiece, it is safer than using your hand and allows
operation with both hands.
•Not overstretch your subject area.
•Do not overreach; ensure proper footing and balance at all times the balance.
•Maintain tools with care.
•Keep your tools sharp and clean to work well and safely. Follow the maintenance instructions
Protected housing (protection class II)!

User’s Manual –AREBOS Impact Wrench
4
and instructions for changing accessories. Regularly check the plug and the cable and have
damage repaired by a qualified electrician. Inspect extension cords periodically and replace if
damaged. Handles dry and free of oil and fat.
•Pull the plug.
•When not in use, before servicing or when changing accessories such as Blades, bits and
machine tools of all kinds
•You can insert any tool key.
•Before you turn that key and adjustment are ntfernt.
•Avoid unintentional starting.
•Do not wear to the mains connected tools with your finger on the switch. Make sure that the
switch is off when connected to AC power.
•Extension cords for outdoor.
•Use outdoors only for approved and appropriately labeled extension cord.
•Stay alert.
•Watch your work, do the sensible and use the tool if you are tired.
•The tool for damage control.
•Before use, the tool always the safety devices and parts carefully for proper and intended
function. Check that the moving parts function correctly, that they are not jammed or
damaged parts. All parts must be correctly installed and meet all the conditions necessary for
the proper operation of the tool to ensure. Protection devices, switches or other parts that
are damaged should be properly recognized by a qualified electrician repaired or replaced.
Do not use tool if switch does not turn on and off the leaves.
•Attention! Use your tools and accessories described in this safety information. Insert your
tool exclusively for the work for which it was designed and look for appropriate working
conditions. Detourned use can lead to dangerous situations.
•Repairs should only be recognized by the expert.
•This power tool complies with relevant safety regulations. Repairs should only be performed
by a qualified electrician and with original spare parts. Violations could cause injury to the
user.
•Attention! When using the equipment, a few safety precautions must be observed to
prevent injury and damage. Read these instructions / with due care. Keep this place, so that
the information is available at all times. If you give the device to other people, give them
these operating / safety instructions as well. We assume no responsibility for accidents or
damages caused by failure to comply with these instructions and safety precautions.
Technical specifications
Model
AR-HE-IW1010
Rated output
1010 W
Torque
450 Nm
Idle speed
2200 rpm
Rated input voltage
230 V
Cable length
2 m
Direction of rotation
Forward; Reverse
Degree of protection
II
Colour
Red

User’s Manual –AREBOS Impact Wrench
5
Use
Operation
•The tool holder with the insert tool is driven by an electric motor via gear and percussion.
•The operation is divided into two phases: screws and tighten it (percussion in action).
•The percussion starts as soon as it leaves the screw and thus the motor is loaded. The impact
mechanism converts to the power of the engine in uniform rotary impacts. When loosening
screws or nuts, that process takes vice versa.
•An overload of the motor is not possible because the striking mechanism disengages when
reaching the rated load.
Commissioning
•Note the power supply! The voltage of the power source must comply with the specifications
on the rating plate of the tool. Marked with 230 V Power tools can be operated with 220
volts.
Cleaning and maintenance
•Do you prefer all the work on the machine the power plug from the socket.
•Keep the machine clean and the vents work to be good and safe.
•Enter all correspondence and spare parts orders, please always include the 10-digit article
number on the nameplate of the power tool on.

User’s Manual –AREBOS Impact Wrench
6
Disposal instruction
Disposal of the packaging
•Please make reference to the guidelines and standards for appropriate disposal of the packaging
valid in your region. In part, the package may consist of plastic bags - watch this respect, with
special care to ensure that this is not out of the reach of children. There is a risk of suffocation!
Disposal of waste equipment
•Equipment must be disposed of in accordance with the rules and regulations of the local waste
disposal.
Meaning of the "dustbin"
Protect our environment; electrical appliances do not belong in household waste.
Use the provided for the disposal of electrical equipment collection points and
enter your electrical and electronic equipment that you no longer use. They help
ensure that the potential effects of incorrect disposal on the environment and
human health to be avoided. So, do your part to recycle, recycling and other
forms of recovery of waste electrical and electronic equipment. Information on
where the devices are disposed of, please contact your local authorities or local
Governments.
Our customer service number: [phone]
Canbolat Vertriebs GmbH • Gneisenaustraße 10-11 • 97074 Würzburg

User’s Manual –AREBOS Impact Wrench
7
EU Declaration of Conformity
We,
Canbolat Vertriebs GmbH, Gneisenaustraße 10-11, 97074 Würzburg, Germany,
Hereby declare that the product named below, seen its design and construction as well as according
to our sales, has been complied with the relevant and basic health and safety EU-requirements.
Name of the product: Impact wrench
Model Nr.: AR-HE-IW1010
Art. Nr.: 4260199750339
If the product has any modification not allowed by us, this declaration loses its validity.
Tested acc. to:
EU Standard:
EN 60745-1: 2009 + A11
EN 60745-2-2:2010
ZEK 01.4-08/11.11
Date/Manufacturer Signature/Location: Würzburg, 06.03.2019
Identification of the signatory:
Korhan Canbolat, head of the company
Authorised representative for the technical documentation:
Korhan Canbolat
Office address:
Canbolat Vertriebs GmbH
Gneisenaustraße 10-11
D-97074 Würzburg
Return address can be found in the imprint: https://www.arebos.de/impressum/
VAT identification number: DE 263752326
Court of the Commercial Register is Würzburg, HRB 10082
WEEE Reg.-No. DE 61617071