Arena Luci BARIO LED User manual

This instruction manual contains important information
about the installation and use of the projector. Please
readandfollowtheseinstructionscarefully.
The security of this device is guaranteed only with the
proper use of the following instructions, therefore they
mustbekeptcarefully.
Neverinstallthedeviceinlocationseasilyaccessibleby
people who ignore the existence of this user's manual
andsafetyinstructions.
Disconnect the unit from any power supply before
attemptinganyoperationincontactorinsidetheunit,and
whennotinuse.
Itisessentialthateachdeviceiscorrectlyearthedand
that electrical installation conforms to all relevant
standards.Neversupplytheunitwithouttheearthlink.
Priortoconnecttheunittothemainssupply,checkthe
outputvoltagefitstechnicalrequirementsonthelabel.
Neverletpowercordcomeintocontactwithothercables.
Nevertouchelectricalcontacts,eitherdirectlywithyour
fingers,orindirectlybymeansofsharpormetalobjects.
Makesurethatcablescannotcausetriphazard.
Donotattempttodismantleandmodifytheunit.
Due to high technological level of this unit, service
maintenanceshouldbeperformedbyspecialisedopera
tors.PleasecontactyourArenaLucidealerforanyissue.
Always ensure that the structure to which you are
attaching the unit is secure and is able to support the
weightofeachunit.
Always make sure you are using a safety chain
connectedtotheunit.
Do not allow contact with water or any other fluids, or
metallicobjects(IP20).
Donotinstalltheprojectorinareasofhighhumidity.The
unitisintendedonlyforindoorpurposes.
Avoidinstallingtheunitclosetoheatsources.
Neverleanthepowercordonhotunitsurfaces.
Allowedtobemounteddirectlyoninflammablesurfaces.
Keepaminimumdistanceof3mbetweenthedeviceand
theilluminatedsurfaces.
Avoiddirectexposuretothelightfromthelamp.Thelight
luminanceisharmfultotheeye.
Installtheunitwhereitcanbeeasilyaerated.
Avoidobstructionofin/outvents.
The lighting apparatus must be used only with its
protectiveshield.
The protective grill, lenses or ultraviolet filter must be
changediftheyarevisiblydamagedtothepointatwhich
their effectiveness is diminished, for example by
becomingcrackedordeeplyscratched.
Toensurethereliabilityoftheprojectoritshouldbekept
clean. The lens and filters should also be regularly
cleaned(atleastonceeverysixmonths)tomaintainan
optimumlightoutput.
Donotuseanysolventbasedcleaningagents.Useonly
asoft,dryantistaticcloth.
The installation of LED modules (including power
supplies)shouldbedoneaccordingtocurrenttechnical
rules and regulations. The installation should be
performedonlybyaqualifiedoperator.
Avoid contact with either corrosive agents or humidity
and moisture on delicate elements: damages from
corrosionarenotrefundedascomponentdefects.
WARNINGS
BARIOLED
User'sManual
ProfileLEDspotwithmanualzoomandDMX
control
Please note that as part of Arena Luci's ongoing commitment to continuous product development,
specifications are subject to change in the course of product improvement without notice.Arena Luci is not
responsiblefordamagesresultingfromimproperordifferentusethanexpected.
PRF0501935DWW
PRF0501935DNW
PRF0501935DW

2/8
BARIOLEDDMX
BEFORESTARTING
Removetheproductfromtheshippingcarton,checking
thatallthecomponentssuppliedarepresentinthebox.
Refer to the following packing list to check which
components must be present in the packaging. If any
componentismissingordamaged,contactyourArena
Lucidealerimmediately.
n°1profilespotBARIOLEDDMX
n°1filterframe
n°1coupleofCanonXLR5poleconnectors
(male/female)
Beforestartingtheinstallationofyourproductmakesu 
rethattherearenoevidentdamagescausedbytrans 
portation.Intheeventthattheprojectorisdamaged,do
not plug it in and do not attempt to use it until you
contactedyourArenaLucidealerforassistance.
INSTALLINGTHEPROJECTOR
Attach the projector by means of the central hole dia 
meter 11mm on the fork; for suspended applications,
youmustalsofixtheprojectorwithasafetychainsecu 
ringittothesupportstructureandtheringontherear
plate,besidesthehandle.
Loosen the side knob to adjust the tilt of the projector
(+50° / 50°); once positioned, tighten the knob firmly.
For a mounting on tripod, the projector should be
installedupsidedown.
Theprojectormustbefixedonasuitablesupportwhich
remainsstableduringoperation.Alwaysmakesurethe
standorstructuretowhichyouaresettingtheprojector
issecureandisabletobeartheweightofeachunit.
POWERSUPPLYMAINS
Disconnectthemainsvoltagefromthesystem.
Connect the power cord to the mains supply, paying
attentiontothevoltageandfrequencyindicatedonthe
label.
Respect the LNE polarity indicated on the terminals
(colorbrown=L,blue=N,yellow/green=E).
It is essential that each projector is correctly earthed
and that electrical installation conforms to all the
standardsofgoodpracticeandsafetyregulations.
The projector does not have builtin on/off switch and
turnsonimmediatelywhenpowerissupplied.
Itisrecommendedthattheprojectorisconnectedtothe
mainsviaaproperswitch,sothatitcanbeturnedon
andoffindividually.
Caution
It is important that the ground connection of each pro 
jectorisrunaccordingtotherulesinforce.Thepower
absorptionoftheprojectoris55W.
FILTERFRAME
Thefilterframefitsinthefrontoftheprojector.Undothe
smallretainingknobontherightsideofthedeviceand
slide it backward to release the filter frame. Now it is
possibletoextractandinsertthefilterholder.
Opentheframeandinsertthecoloredgelandthenput
itbackinplaceontheprojector.Payattentiontokeep
thenotchontheframetotherightsideoftheprojector,
tomatchthefilterholder.Slideforwardtheknobandfa 
stenittolockthefilterframe.

3/8
USER'SMANUAL
MANUALZOOMADJUSTMENT
Use the two knobs underneath the projector to ma 
nuallyadjusttheapertureofthelightbeamtosuitany
typeofinstallation.
The beam spread can be adjusted from 19°
(handlesapart)to35°(handlestogether).
CONNECTINGCONTROLSIGNALS
Theprojector,inordertoberemotelycontrolled,requi 
res a digital signal DMX 512 (1990). The connection
betweencontrollerandprojectorandbetweenprojector
andprojectormustbemadewithtwocoreshieldedca 
ble with a section of at least 0.5mm2 and connectors
modelCanonXLR5pinplugandsocket(supplied).In
carryingoutthewiringoftheconnectorsitisimportant
that the signal wires do not make contact with each
otheranddonottouchthecasingoftheplug.Theca 
sing of the plug must not be in contact with other ob 
jects possible sources of disturbance. The three
terminals have the numbering referred to the poles of
theXLRconnectorsnormallyusedfortheconnectionof
the DMX: pin 1 = GND or braided screen, pin 2 =
DATA or cold pole, pin 3 = DATA+ or hot pole. Pin 4
andpin5arenotconnected.
Connect the signal coming from the controller to the
DMXsocketoftheprojectorlabeledDMXIN.Continue
connectingtheDMXOUTsockettotheDMXINsocket
ofthenextprojector.
TerminationoftheDMXsignal
Forinstallationswherethecablesignalmusttravellong
distances or where there are electrical noises, for
example a discotheque, it is recommended to use a
DMXterminator.TheDMXterminatorissimplyanXLR
connector with a resistance of 120Ω (Ohm) between
pins 2 and 3.The connector is then plugged into the
DMXOUTsocketonthelastprojectorinthechain.

4/8
BARIOLEDDMX
PROJECTORADDRESSES
The projector, to be remotely controlled, requires 2
DMX channels. Each projector must be given a digital
start address number so that the correct projector re 
sponds to the correct control signals.This digital start
address is the channel number from which the pro 
jector starts to “listen” to the digital control information
beingsentoutfromthecontroller.Thisdigitalencoding
mustbedoneoneachprojector.
The start address of the coding is assigned by setting
thedesiredvalueusingthedisplayinterfaceontherear
panel. Press the MENU button on the keypad, the
display shows the word DMX ADDR and the DMX
address that is currently set for the projector; use the
UP or DOWN buttons to select the desired starting
address(ie.projector1address1,projector2address
3, projector 3 address 5, etc.); for fast forward press
andholdthebutton.
Youcanquicklyjumptotheminimumvalue(001)orthe
maximum value (511). To set the minimum, press UP
whilepressingDOWN;tosetthemaximum,pressDO 
WNwhilepressingUP.
PressENTERtostore(thedisplayshows-STORED-),
orpressMENUtoreturn.
The number of selectable base addresses from the
electronicboardrangesfrom1to511.
OPERATION
Aftersupplyingthedevice,thesoftwareperformsare 
set; at the end of the electronics reset routine, the
displayshowstheidlestate.
Intheidlestateyoucangetmanyinformations:
D001 . 100
38'C
D001isthebaseaddressoftheprojector.
.(blinkingdot)indicatesthepresenceofavalidDMXsi 
gnal.
100isthemasterdimmerlevel(expressedin%).
38'Cistheinternaltemperatureofprojector,in°C.
In the absence of DMX signal (XLR connector
unplugged),theblinkingdotisoff.After60secondsof
inactivity,thedisplaybacklitshutsoff.Pressanykeyto
switchitonagain.
Set the base address of the projector as seen before
Fig.01WiringdiagramforDMXsignalremotecontrol

5/8
USER'SMANUAL
and connect the signal from DMX controller to control
thevariousfunctionsoftheprojector.
WhentheprojectorisreceivingaDMXframe,ifthesi 
gnalislost(orthecableisdisconnected)theprojector
holdsthecurrentlevelsofDMXchannelsandtheLED
sourceisstilldrivenwiththelevelssentinthelastvalid
DMXframe.
Then,iftheprojectoristurnedoffandon,anditisnot
connected to a valid DMX signal, the light intensity is
brought to 0% (unless you changed the option menu
"manual"priortoswitchoff,seelaterinoptionsettings).
ShouldthetemperatureoftheLEDboardincreaseover
85°C, the electronic management automatically redu 
cesthelightintensityinordertobringthetemperature
backtoacceptablevalues.
Inaddition,thebrightnessofthelightisbroughttozero
when the temperature on the LED board rises above
100°C.
OPTIONMENU
To activate the display press any button. Then to
access the options of the projector press the MENU
button. The display shows the name of the option
starting from option 1, the base DMX address. Press
again the MENU button to scroll through the list of
options. Adjust the value with UP or DOWN buttons,
thenconfirmyourchoicewithENTER(thedisplaysho 
ws-STORED-).
Ifyoudon'tpressENTER,allyourchangeswillbelost:
after 20 seconds of inactivity inside the options menu,
thedisplayreturnsbacktotheidlestate.
Option1DMXaddress
When the display shows DMX ADDR with the current
DMXaddress,presstheUPorDOWNbuttonsasma 
nytimesasrequiredtodisplaythenumberofthedesi 
redchannel.Tofastforwardpressandholdthebutton.
Remember that you can quickly jump to the minimum
value(001)orthemaximumpossiblevalue.Tosetthe
minimum, press UP while pressing DOWN; to set the
maximum,pressDOWNwhilepressingUP.
PressENTERtostoreorMENUtogoback.
Option2Manuallevelsettings
Manual settings are only effective when there is no
DMX signal connected, instead they have no effect
when the DMX signal is present (message -ERROR-
shown).
WhenthedisplayshowsMANUAL,inthesecondrowit
shows the channel number (starting from 1) and the
current manually set level in DMX units, for example
CH1: 255.
Thechannelnumberisblinking,whilethechannellevel
issteady.UsetheUPorDOWNbuttontoswitchtothe
desired channel (1 to 2), then press ENTER: now the
channel number is steady and the channel level is
blinking, indicating that you can modify its value. Use
UP or DOWN to adjust the channel level; for fast
forwardpressandholdthebutton.ThenpressMENU
toreturntothechannelselection.
Remember that you can quickly jump to the minimum
value(001)orthemaximumvalue(255).Tosetthemi 
nimum,pressUPwhilepressingDOWN;tosetthema 
ximum,pressDOWNwhilepressingUP.
Repeat the above steps until you finish your manual
settings. Finally press ENTER to save your job, the
displayshows-STORED-.
Thevaluesarestoredintothepermanentmemory,and
willbereproduceduntilyouconnecttheDMXsignal.
Note:
Afteryousetthemanualvalues,whentheprojectoris
turned off and on, and it is not connected to a valid
DMXsignal,thechannelslevelsforch.1,ch.2areauto 
maticallyrecalledfrommemoryandtheLEDsourcewill
behaveaccordingly.
If you connect a DMX signal and then remove it, the
stored values become "disabled" and at the next igni 
tion (without DMX) the manual values will be ignored;
thelightintensityisbroughtto0%,whilech.2issetto0.
Inallcases,ifyouswitchontheprojectorwithavalid
DMX signal connected, the manual settings are igno 
red.
Remember that if you don't press ENTER to save in
memory, themanualsettingswillbelostandwon'tbe
recalledatthenextpoweron.
Option3FanMode
This function relates to the control of the LED cooling
fan.
When the display showsFAN MODE, the second row
showsthecurrentoperatingmodeandyoucanchange
itbypressingUPorDOWNbutton:
MAX
Thefanisalwaysonatmaximumspeed.
OFF-MAX
Thefanisswitchedoffuntilthetemperatureisbelowa
minimumsetpoint(50°C),thenitstartsblowingatmini 
mum speed and gradually increases in speed as the
temperature rises, reaching the maximum speed at
70°C.
MIN-MAX
The fan is always on at minimum speed when the
temperature is below a minimum setpoint (50°C), and
graduallyincreasesinspeedasthetemperaturerises,
reachingthemaximumspeedat70°C.
Press ENTER to confirm (the display shows
-STORED-forawhile)orpressMENUtoquit.
Option4SoftwareVersion
WhenthedisplayshowsSW REV.youcanreadinthe
second row the current software release installed on

6/8
BARIOLEDDMX
theprojector.
PressMENUorwait20secondstogoback.
DMXCHANNELFUNCTIONS
Inthefollowingdiagramsyouwillfindthecontrolvalues
inDMXunits(0255)forall2channelsoftheprojector.
Channel1Dimmer
Theintensityoflightisvariableinalinearwayfromoff
tothemaximum;inparticular,forDMXvalueequalto0
the LED source is off, for increasing intermediate va 
luesthebrightnessgraduallyincreases,forvalueequal
to255theLEDsourceisonatitsmaximumintensity.
Channel2Strobe
The projector is able to generate an electronic strobe
effect, obtained by rapidly switching on and off the
LED.ThestrobeisdisabledforDMXvaluesbetween0
and 9, while for values between 10 and 255 the fre 
quencyoftheflashesgraduallyincreases.
RDMFUNCTIONS
The Remote Device Management Protocol (RDM)
permits intelligent bidirectional communication
between devices from multiple manufacturers. RDM
permitsaconsoleorothercontrollingdevicetodiscover
and then configure, monitor and manage intermediate
and enddevices connected through a DMX512
network.
RespondersandControllersidentifythemselveswitha
48bitUniqueID(UID).TheUniqueID(UID)consistsof
a16bitManufacturerIDwitha32bitDeviceID.
The32bitdeviceIDisuniquethroughoutallproducts
manufactured under a specific Manufacturer ID, to
ensure that no two devices with the same UID will
appearontheDMX512network.
TherecommendedmethodforrepresentingtheUIDin
text is in hexadecimal format with a colon separating
theManufacturerIDandtheDeviceID.
Anexampleofsuchwouldbe:
mmmm:dddddddd
where mmmm is the Manufacturer ID in hexadecimal
andddddddddistheDeviceIDinhexadecimal.
ManufacturerIDforArenaLuciis:
0x00B0
Device ID forArena Luci products consists of a 12bit
ProductIDfollowedbya20bitSerialNumber.
ProductIDforDalìLEDis:
0x047forPRF0501935DWW
0x048forPRF0501935DNW
0x049forPRF0501935DW
The UID that would appear on RDM Controllers is
then(e.g.0x00001istheSerialNumberinhexaecimal):
00B0:04700001forPRF0501935DWW
00B0:04800001forPRF0501935DNW
00B0:04900001forPRF0501935DW
RDMParameterMessages
RDM Parameter Messages are  sent to set configu 
rationandgetstatusinformationfromthedevice.
Get/SetIdentifyDeviceIDENTIFY_DEVICE
Thisparameterisusedfortheusertophysicallyidentify
thedevicerepresentedbytheUID.
Whena"StartIdentify"issentfromtheRDMcontroller
to the projector, the projector will respond by strobing
the light. To stop the strobing after detecting the unit,
send"StopIdentify".
GetDeviceInfoDEVICE_INFO
This parameter is used to retrieve a variety of
information about the device that is normally required
byacontroller.
RDMProtocolVersion:
Thisfieldcontainstheversionnumberofthepublished
RDMStandardsupportedbythedevice.
BarioLEDreturns1.00.
DeviceModelID:

7/8
USER'SMANUAL
This field identifies the Device Model ID of the Root
DeviceortheSubDevice.
BarioLEDreturns
00.47forPRF0501935DWW
00.48forPRF0501935DNW
00.49forPRF0501935DW
ProductCategory:
ThisfieldreportsaProductCategorybasedonthepro 
duct’sprimaryfunction.
BarioLEDreturnsFixtureFixed.
SoftwareVersionID:
This field indicates the Software Version ID for the de 
vice.
BarioLEDreturns
04.70.01.00forPRF0501935DWW
04.80.01.00forPRF0501935DNW
04.90.01.00forPRF0501935DW.
DMX512Footprint:
This field specifies the DMX512 footprint (number of
consecutive DMX512 slots required). This information
can be used in conjunction with DMX_ 
START_ADDRESSforautopatchingcapabilities.
BarioLEDreturns02.
DMX512Personality:
This field specifies the current DMX512 Personality
setting for the projector and also the total number of
personalitiesavailable.
BarioLEDreturns01/01.
DMX512StartAddress:
ThisfieldshowsthecurrentDMX512StartingAddress.
SubDeviceCount:
This parameter is used to retrieve the number of Sub
DevicesrepresentedbytheRootDevice;adevicemay
containoneormoresubdevices,allhavingacommon
setofparameters.Anexampleofadevicewithsubde 
vicesisadimmerrackcontaininganumberofdimmer
modulesubdevices.
BarioLEDhasn'tanysubdevice.
SensorCount:
Thisfieldindicatesthenumberofavailablesensorsina
RootDeviceorSubDevice.
SensorswillbeaddressedusingotherRDMsensorre 
latedparametermessages.
BarioLEDhasn'tanyaddressablesensor.
Get/SetDMX512StartingAddress
DMX_START_ADDRESS
ThisparameterisusedtogetorsettheDMX512start
address. Use your RDM controller's commands to set
thedesiredDMXaddress.
GetSoftwareVersionLabel
SOFTWARE_VERSION_LABEL
This parameter is used to get a descriptiveASCII text
label for the device’s operating software version. The
descriptivetextreturnedbythisparameterisintended
fordisplaytotheuser.Thelabelmaybeupto32cha 
racters.
BarioLEDreturns1.00.
TheSoftwareVersionIDfieldfromtheDEVICE_INFO
parametershouldbeusedforcomparingdevicesfrom
thesameManufacturerwiththesameDeviceModelID
to determine if they are running identical software
versions.
Get/SetDMX512Personality
DMX_PERSONALITY
Thisparameteris usedtoset theprojector’s DMX512
Personality. Manydevicessuchasmovinglightshave
different DMX512 Personalities. Many RDM parame 
tersmaybeaffectedbychangingpersonality.
BarioLEDhasonepersonality:
Mode1:2ch./02.
Parameter PERSONALITY_DESCRIPTION contains
the Personality Requested, the DMX512 Footprint for
that Personality, along with up to 32 characters of de 
scription.
BarioLEDreturns:
Personality#01
SlotRequired:02
Descrip:Mode1:2ch.
GetDeviceModelDescription
DEVICE_MODEL_DESCRIPTION
Thisparameterprovidesatextdescriptionofupto32
characters for the device model type. Bario LED re 
turns:
ProfileDMXandManualzoom.
GetManufacturerLabel
MANUFACTURER_LABEL
This parameter provides anASCII text response with
theManufacturernameforthedeviceofupto32cha 
racters.
BarioLEDreturns:
ARENALUCIITALY.
Get/SetDeviceLabelDEVICE_LABEL
This parameter provides a mean of setting a
descriptive label of up to 32 characters for each
device.Thismaybeusedforidentifyingadimmer
racknumberorspecifyingthedevice'slocation.By
defaultthisfieldisempty.

8/8
BARIOLEDDMX
WARRANTYCONDITIONS
The unit is guaranteed for 24 months from the date of
purchase against defects in workmanship or materials
thatcomposeit.
This warranty does faults due to incorrect or improper
useofthedevice.
The warranty is immediately void if the unit has been
tamperedwithoropenedbyunauthorizedpersonnel.
The warranty provides, at the discretion ofArena Luci,
repairorreplacementoffaultyequipment.
Theserialnumberandmodelofthedevicearerequired
to obtain information or assistance from the dealer. We
invite you to transcribe them in time: for any request of
information or services, this will result in a quick and
effectiveoperation.
CERULES
The device meets the essential requirements of the
Directives LVD 2014/35/UE, EMC 2014/30/UE, RAEE
2012/19/UE, RoHS 2011/65/UE, Ecodesign
2009/125/CE  reg. (UE) 1194/2012, Energy label
2010/30/UE  reg. (UE) 874/2012  reg. (UE) 518/2014,
GPSD2001/95/CE.
Warnings
Disposal of Old Electrical & Electronic Equipment
(applicable in the European Union and other European
countrieswithseparatecollectionsystems).
The product shall not be treated as household
wastebutmustbehandedovertotheapplicable
collectionpointfortherecyclingofelectricaland
electronicequipment.Byensuringthisproductis
correctly disposed, you will help prevent potential
negativeconsequencesfortheenvironmentandhuman
health,whichcouldotherwisebecausedbyinappropriate
waste handling. The recycling of materials will help to
conserve natural resources. For more detailed
informationaboutrecyclingofthisproduct,pleasecontact
yourcityoffice,yourhouseholdwastedisposalserviceor
yoursupplier.
ArenaLucisrlviaSvizzera12/1446042CastelGoffredo(MN),Italy
Tel.+390376782411Fax+390376780973
www.arenaluci.com[email protected]
Powersupply
Powerconsumption
Source
ColourTemperature
Cooling
Beamaperture
Control
Connection
Material
Colour
Insulationclass
Weight
Dimensions
Protection
AmbientTemperature
Suitabletobefittedonnormallyinflammablesurfaces
Appliedstandards
230VAC50Hz
55Wmax
LEDmodule,interchangeable
3000K(WW)4000K(NW)5700K(W).CRI>90
Heatsinkwithlownoiseaxialfan,max8dB.
Manualzoom19°÷35°
DMX512,2controlchannelswithRDM
Threepolespowercord
Aluminiumandsteelplate
Epoxypowderpaintfinish,black
I
4.8kg(includedfilterframe)
420x114x135mm(body)
IP20
From15°Cto+40°C
TECHNICALSPECIFICATION
PRF0501935DENR2|06/2019