Argo Nuk User manual

15
V 01/18
PORTABLE AIR CONDITIONER (LOCAL)
OPERATING INSTRUCTIONS
Read the instructions carefully before operating the appliance or carrying out maintenance work.
Observe all the safety instructions; failure to observe the instructions may lead to accidents and/or
dama
g
e. Store these instructions in a safe place for future reference.
EN

16
V 01/18
The Refrigerant R290
 To realize the function of the air conditioner unit, a special refrigerant circulates in the
system. The refrigerant is the fluoride R290 = 3 GWP (Global warming potential). This
refrigerant is flammable and inodorous. It can lead to explosions under certain conditions,
however the flammability of this refrigerant is very low and it can be ignited only by fire.
 Compared to other common refrigerants, R290 is a non-polluting refrigerant with no harm
to the ozonosphere and a no effect upon the greenhouse effect. R290 has very good
thermodynamic features which lead to a really high energy efficiency. The units therefore
need less filling.
Warning:
Do not try to accelerate the defrosting process or to clean the appliance in different ways other
than those recommended by the manufacturer. Should repair be necessary, contact your
nearest authorized Argoclima Service Centre. Any repairs carried out by unqualified personnel
may be dangerous. The appliance has to be stored in a room that doesn’t have any continuously
operating ignition sources. (for example: open flames, an operating gas appliance or an
operating electric heater.) Do not pierce or burn.
Appliance has to be installed, operated and stored in a room with a floor area larger than 4 m2.
For repairs, strictly follow manufacturer’s instructions only for appliances filled with R290
flammable gas. Be aware that refrigerants do not have any odour.
Appliance filled with flammable gas R290.
Before installing and using the appliance, read the owner’s manual.
Before repairing the appliance, read the service manual.

17
V 01/18
GENERAL OPERATING AND SAFETY INSTRUCTIONS
 This appliance is a local air conditioner designed for domestic use.
 Only use this air-conditioner as described in this manual.
 Ensure that the required voltage and frequency (220-240 V/50 Hz)
match the available power source.
 Fuse style T, 250V AC, 2A, the electricity passing through the fuse
cannot be above 2A.
 This appliance can be used by children aged from 8 years and
above and people with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
 Children shall not play with the appliance.
 Cleaning and user maintenance shall not be made by children
without supervision.
 Ensure that the electricity system is able to deliver the operating
current required by the air conditioner, in addition to that normally
absorbed by other appliances (household appliances, lighting
system, etc.). Please refer to the maximum power input data
indicated on the air conditioner's data plate.
 Connection to the electricity grid must take place in accordance with
current installation standards.
 Ensure that the automatic switches and system protection valves
are able to withstand a start-up current of 5A (normally for less than
1 second).
 The system socket must always be fitted with an efficient earth
connection.
 Make sure that the plug is fully inserted. Do not use multiple
adapters. Do not touch the plug with wet hands. Make sure that the
plug is clean.

18
V 01/18
 Do not use the plug as a means by which to start/stop the air
conditioner: use the ON/OFF button on the remote control or on the
control panel.
 Do not install the air conditioner in rooms where it may receive
water splashes (e.g. laundry rooms).
 This air conditioner can be used by children of 8 years of age or
older, and by persons with reduced physical, sensory and mental
abilities or who lack the necessary know-how and experience to
operate it, if under the supervision or instruction of a person
responsible for their safety, so that they are fully aware of the
attendant risks.
 Before moving or cleaning the device, ensure that it is unplugged
from the socket.
 Do not move the air conditioner while it is operating; first turn the
appliance off, check for any condensate build-up and empty it if
necessary.
 To turn the appliance off, set the remote control to OFF and remove
the plug from the socket. Pull on the plug only. Do not pull the cord.
 Do not use the appliance if the cord or plug are damaged. If the
power supply cord is damaged, it must be replaced by the
manufacturer, dealer or a similarly qualified person so as to avoid
any safety risks.
 Keep the unit away from fire, possible fire sources, inflammable or
explosive objects.
 Do not leave the unit unattended while it’s operating, turn the unit off
and unplug it.
 If drainage hose is used, the ambient temperature musnt’t be lower
than 0°C. It can cause water leakage to the air conditioner.
 Do not splash or pour water on the air conditioner
PRECAUTION!
Do not insert any objects into the air conditioner: this is very
dangerous as the fan rotates at high speed.

19
V 01/18
 Ensure that air circulates freely around the unit. Do not cover
the air intake and delivery grilles with drapes or other items.
WARNING!
 The air conditioner must be positioned at least 50 cm away from
the wall or other obstacles, on a flat and stable surface so as to
avoid water leakages.
 The air conditioner is equipped with a compressor overload
protection system, whereby the compressor only starts once 3
minutes have elapsed from its previous stoppage.
 Please wait at least 3 minutes before starting the unit. This
helps to prevent the compressor from being damaged.
WARNING!
In the event of an anomaly, switch the appliance off and unplug
from the socket. Do not dismantle or attempt to repair or modify
the product. In the event of a malfunction, contact the after-
sales service centre directly.
WARNING!
 Do not expose the air conditioner to direct sunlight as this may
alter the colour of the materials; in addition, possible
overheating of the product may activate the protection
mechanism, causing it to switch off.
 Do not use insecticides, oils, detergents or spray paints near
the appliance; do not use aggressive chemical detergents to
clean the casing as this may damage the finish and colour.
 Close all open windows to maximise air conditioning
efficiency.
The manufacturer shall not be held liable if the relevant safety
and accident prevention rules are not observed.

20
V 01/18
DESCRIPTION OF THE APPLIANCE
FRONT VIEW
SIDE VIEW
REAR VIEW
Min/max operating limits (internal temperature)
Cooling: 18 °C DB / 35 °C DB
Dehumidification: 18 °C DB / 35 °C DB
Cooling mode room temperature adjustment range: 16 °C DB / 31 °C DB
1) CONTROL PANEL AND FUNCTION BUTTONS
WITHOUT REMOTE CONTROL
2) HORIZONTAL FINS AND AIR INTAKE
3) WHEELS
4) LATERAL AIR INPUT
5) LATERAL REMOVABLE FILTER
6) REAR PANEL
7) FRONT PANEL
8) POWER CORD
9) AIR INPUT AND REAR REMOVABLE FILTER
10) REMOTE CONTROL
9) A
1
(10)
1
2
3
4
7
6
8
9
5

21
V 01/18
APPLIANCE START-UP
Open the packaging and remove the box from above. Remove the product and the other elements supplied (illustrated in
the box below).
Remote control
Type
AAA
batteries
for the
remote
control
Round fitting to position between the
air discharge outlet and the flexible
pipe.
Hose
End fitting for window
Window unit kit with plug.
Round fitting for window
unit, for positioning
between the end of the
tube and the window unit
itself.
Drainage tube.
Position the product vertically on a flat and stable surface, as close as possible to a window and at least 50 cm from walls
or other nearby obstacles.
USE WITH END FITTING FOR WINDOW
Connect the flat fitting to the hose, extend the
hose as far as necessary for reaching the outside
and it connect to the back of the air conditioner.
Next, slide the flat fitting downwards into the grooves (A)
and secure it with the hook (B).
The upward-facing side of the flat fitting is marked "TOP".

22
V 01/18
Connect the round window fitting (1) to the end
of the hose then the end fitting for the window (2),
previously obtained by joining parts A and B
Open the windows and lock one of the two leaves with the
handle.
Place the end fitting against the fixed leaf of the window,
and draw the other leaf towards it.
USE WITH WINDOW UNIT KIT
Make a hole measuring roughly 135 mm through
the window pane.
Insert the window unit without its closure cap into the
window. Insert the round fitting into the retractable hose
and insert the retractable hose with the round fitting into
the window unit.
Insert the flat fitting onto the hose. Insert the assembled hose into the back of the air
conditioner.
The outlet must be between 40 cm and 130 cm above the
ground.
Avoid tight curves or bends in the flexible hose.
When the air conditioner is not being used, disconnect
the hose and fit the closing cap.

23
V 01/18
Connect the power cord to a suitable electrical socket (220-240 V). Insert the batteries supplied into the remote control,
while observing the polarities. Select the desired operating mode from the remote control.
HOW TO USE THE APPLIANCE
This appliance can be used for cooling, dehumidifying and ventilating.
When switching between modes, the fan continues to rotate but the compressor stops: the compressor will start after 3
minutes. This delay protects the compressor from potential damage.
Dehumidification
THE DISCHARGE TUBE MUST ALWAYS BE CONNECTED to the appliance: the only exception is when the
appliance is used solely for dehumidification, in which case it is advisable to let the appliance discharge directly
into the environment for maximum efficiency (consult the "Dehumidification Mode" paragraph).
Regularly clean the air filters beneath the easily removable rear grille to keep the air conditioner working efficiently.
OPERATING MODES
1. COOLING MODE (COOL)
 The "Cool" LED on the control panel will turn on.
 The temperature can be adjusted to between 16 °C and 31 °C.
 In this mode, the fan speed can be adjusted and the Timer function can be set.
 For more silent operation, run the fan at low speed.
2. DEHUMIDIFICATION MODE (DEHUM)
 Press the MODE button to select Dehumidification.
 The temperature is automatically set 2 degrees below the room temperature.
 The fan speed is set to low and cannot be adjusted.
NOTE
The air conditioner does not cool the room when it is used as a dehumidifier.
When the appliance is used as a dehumidifier, the flexible hose must not be connected.
For maximum dehumidification efficiency, leave the rear discharge attachment free to discharge directly into
the environment.
The dehumidification mode is recommended during autumn and winter.
If used in summer, it is best to leave the flexible hose attached so that the hot air can be discharged towards
the outside rather than into the room.
3. VENTILATION MODE (FAN)
 Press the MODE button to select Fan and wait until the relative icon appears.
 In this mode, the fan speed can be adjusted.
 The temperature cannot be adjusted.
Cooling, Ventilation

24
V 01/18
CONDENSATE ELIMINATION
This appliance automatically vaporises condensate in cooling mode.
Ensure that when the unit is operating in cooling mode, the rubber caps closing the
drainage holes on the rear of the appliance are properly positioned. When the tank
is full, the “Full Tank” led will light up.
To empty the container, switch the air conditioner off and unplug it. Remove the
cap form the rear drainage hole and direct it over a normal drain.
Ensure that the tube is not twisted or bent. The tube must slope downwards. Re-
close the drainage hole with the cap and resume use of the air conditioner.
REMOTE CONTROL OPERATION
Insert the batteries into the remote control, while respecting the indicated
polarities.
Only use type AAA 1.5V batteries.
Remove the batteries if the remote control is not used for a month or
longer.
Do not attempt to recharge the batteries. Replace all batteries at the same time.
Do not throw the batteries into fire: they may explode.
INFORMATION FOR CORRECT DISPOSAL OF THE BATTERIES PURSUANT TO EUROPEAN DIRECTIVE 2006/66/EC
Replace the batteries when depleted. At the end of their working life, batteries must be disposed of separately from unsorted
waste. They must be must be delivered to appropriate separated waste disposal plants or to dealers that provide a similar service.
Separate waste disposal of batteries prevents potential negative effects on the environment and human health resulting from
inadequate disposal, and also allows the materials from which it is made to be recovered and recycled in order to achieve
significant savings in terms of energy and resources. The separate disposal obligation is underlined by the crossed-out dustbin
symbol appearing on the battery. Illegal disposal of the product by the user is subject to administrative penalties as per current
regulations.
DRAIN HOLE

25
V 01/18
FOR OPTIMAL REMOTE CONTROL OPERATION, POINT THE TRANSMITTER HEAD TOWARDS THE
RECEIVER LOCATED ON THE AIR CONDITIONER.
The remote control can be activated by pressing the ON/OFF button on the portable unit. The icon on the remote control
display will flash once and a buzzer will sound to indicate that the signal was transmitted to the air conditioner.
In the OFF mode, the set temperature and set timer will appear on the remote control.
1. ON/OFF BUTTON
2. MODE BUTTON
3. BUTTON
4. BUTTON
5. FAN BUTTON
6. TIMER BUTTON
CONTROL PANEL
a. POWER ON/OFF BUTTON
b. BUTTON
c. RECEIVING SENSOR
d. SPEED BUTTON
e. TIMER BUTTON
f. BUTTON
g. MODE BUTTON
(1) ON/OFF BUTTON
Press this button to switch the unit on or off.
(2) MODE BUTTON
When the unit is on, press this button to choose the desired mode among: COOLING, FAN and DEHUMIDIFYING.
(3) BUTTON TEMP
Press this button to adjust the temperature and set the time.
(4) BUTTON TEMP
Press this button to adjust the temperature and set the time.
(5) SPEED BUTTON
In the cooling and fan modes, press this button to adjust the ventilation speed to low (Low) or high (High). In certain
conditions, the fan speed may not function according to the settings.
In dehumidifying mode, this button cannot be pressed, thus the fan will forcefully choose the low fan speed.
a b c d e
f g
1
3
6
2
4
5

26
V 01/18
(6) TIMER BUTTON
a. When the air conditioner is off, press “TIMER” to set when to switch the unit on. Press “+” o “–“ to set the time.
b. When the air conditioner is on, press “TIMER” to set when to switch the unit off. Press “+” o “–“ to set the time.
TROUBLESHOOTING
Troubles Possible Causes Su
gg
ested Remedies
1. Unit does not start when pressing
power button
- Water full indicator lamp blinks, and
water tank is full.
Dump the water out of the
water tank.
- Room temperature is lower than the
setting temperature. (Cooling mode)
Reset the temperature
2. Not cool enough - There are heat sources inside the room. Remove the heat sources if
possible
- Exhaust air hose is not connected or
blocked.
Connect or clean the
exhaust air hose.
- Temperature setting is too high. Reset the temperature
- Air inlet is blocked. Clean the air inlet.
3. Noisy - The ground is not levelled or not flat
enough
Place the unit on a flat, level
ground if possible
- The sound comes from the flowing of the
refrigerant inside the air conditioner
It is normal.
4. E0 Code Room temperature sensor failed Replace room temperature
sensor (the unit can also
work without replacement.)
5. E2 Code Water tank full Please empty the water
tank.
CARE AND MAINTENANCE
WARNING!
Prior to carrying out any cleaning or maintenance, unplug the unit from the power socket.
1. Cleaning the air filters
The air filter must be checked at least once every two weeks of operation. Operating with dirty or clogged filters will
decrease the effectiveness of the air conditioner and can cause serious problems.
To remove the filter, release the rear grille then slide out the filter by gently pulling it sideways.
Use a vacuum cleaner to remove any dust. Should this not
be sufficient, wash the filter with lukewarm water and
neutral detergent (if necessary), rinse it with cold water
then leave it to dry naturally before putting it back in place.
After putting the filter back in place, close the grille and
resume use of the air conditioner.
2. Cleaning the casing.
Use a soft damp cloth to clean the outer surface of the air conditioner.
Do not use excessively hot water, solvents, petrol or other aggressive chemical
compounds, talcum powder and brushes: they may damage the surface or
colour of the casing.
Remove any stains using warm water with a little neutral detergent.
Do not pour water onto the air conditioner to clean it: this may damage the
internal components or cause a short circuit.
3. Storage.
When you do not envisage using the air conditioner for a long time, clean the
filters before storing it away.
Keep the appliance in a vertical position at all times. Do not place any heavy objects on the
top and, if possible, protect the air conditioner with a plastic sheet.

27
V 01/18
4. Transport.
Preferably keep the air conditioner in the vertical position
when transporting it.
Should this not be possible, rest it on its right-hand side;
when it reaches its destination, immediately put the
appliance in the vertical position and wait at least 4 hours
before using it in the cooling mode.
5. For complete safety, regularly check the condition of the power cord; should it be damaged through use,
contact the Service Centre to replace it.
TIPS FOR MAXIMISING COMFORT AND MINIMISING CONSUMPTION
CHECK that:
 the unit's extraction and delivery grilles are always unobstructed;
 the air filters are always clean: a dirty filter will decrease the passage of air and thus reduce the unit performance;
 the doors and windows are closed, to avoid infiltration of unconditioned air;
 the flexible hose is correctly positioned, without folds or sharp bends;
 the room temperature is above 18 ºC for the cooling mode, and above 10 ºC for dehumidification mode.
REGULATION (EU) No. 517/2014 - F-GAS
The unit contains R290, a natural gas with global warming potential (GWP) = 3. Do not release R290 into
the atmosphere.
Kg. 0.14 = 0.00042 Tonn CO2 equiv
INFORMATION FOR THE CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EUROPEAN
DIRECTIVE 2012/19/EU
This appliance may not be scrapped with domestic waste at the end of its life cycle. We call your attention to
the crucial role played by the consumer in the re-use, recycling and other forms of recovery of such waste.
The appliance must be scrapped by a sorted waste disposal centre or by returning it to the retailer (no charge is
levied for this service), when you purchase a new equivalent appliance.
Sorted disposal of electric and electronic equipment prevents the negative effects on the environment and
human health resulting from improper scrapping, and also allows the materials from which it is made to be
recovered and recycled, with significant savings in terms of energy and resources.
The sorted disposal requirement is indicated by the crossed waste bin label affixed to the appliance.
www.ar
g
oclima.com