Arm's Reach Ideal Ezee Co-Sleeper User manual

The Ideal Co-Sleeper
Ezee 3 in 1
TM
Bedside Sleeper Free-Standing Bassinet Play Yard
by Arm's Reach®
R

FALL HAZARD - To help prevent falls, do not use this product when infant begins to push
up on hands and knees or has reached manufacturer’s recommended maximum weight of
18 lbs, whichever comes first.
BASSINET WARNINGS
SUFFOCATION HAZARD
On soft bedding
Use only the pad provided by manufacturer. NEVER add a pillow, comforter or another
mattress for padding.
If a sheet is used with the pad, use only the one provided by Arm's Reach.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
backs to sleep, unless otherwise advised by your physician.
A bedside sleeper is designed to provide a sleeping area for an infant until he or she
begins to push up on hands and knees or approximately 5 months of age. Move your child
to another sleeping product when your child reaches this stage.
Entrapment Hazard—To prevent death from entrapment, bedside sleeper must be properly
BEDSIDE SLEEPER WARNINGS
secured to adult bed using the attachment system.
- There must be no more than 1⁄2 in. (13 mm) gap between bedside sleeper and adult bed.
- Check tightness before each use by pulling bedside sleeper in a direction away from
adult bed.
- If gap exceeds 1⁄2 in. (13 mm), DO NOT use product. Do not fill the gap with pillows,
blankets or other items that are suffocation hazards.
Always read and follow assembly instructions for each product use mode (bedside sleeper,
bassinet, play yard).
Always use ALL required parts for each use mode. Check instruction manual for a list of
required parts. Periodically check product for loose, damaged, or missing parts.
The anchor plate and straps assembly must always be used in bedside sleeper mode.
Never use this product if there are any loose or missing fasteners, loose joints, broken
parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact
Arm's ®
Reach Concepts, Inc. for replacement parts. Never substitute parts.
2
STRANGULATION HAZARD : When anchor plate and strap assembly is not in
use, store in a safe place not accessible to children.
WARNING:

In gaps between a mattress too small or too thick and product sides.
On soft bedding.
NEVER add a mattress, pillow, comforter, or padding.
Use ONLY mattress/pad provided by Arm's Reach Concepts, Inc.
®
The product including side rails must be fully erected prior to use.,,
Top support member must be installed prior to use. Failure to install may result in child falling
out of the product.
Strings can cause strangulation! Never place items with a string around a child's neck such as
hood strings or pacifier cords. Never suspend strings over product or attach string to toys.
Discontinue use of the product when child is able to climb out or reaches the height of
35 in. (890mm).
PLAY YARD POSITION WARNINGS
Infants can suffocate
Never place product near a window where cords from blinds or drapes can strangle a child.
Always provide the supervision necessary for the continued safety of your child. When used
for playing, never leave child unattended.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs
to sleep, unless otherwise advised by your physician.
FALLING HAZARD: Remove infant from this product before starting any conversion.
Never use more than 3- 2” (5cm) extensions with this product to match the height of the adult
bed mattress. Do not use leg extensions when the product is NOT attached to the adult bed.
Child can become entrapped and die when improvised netting or covers are placed on
top of product. Never add such items to confine child in product.
When child is able to pull to standing position, set mattress/base to lowest adjustment
position and remove bumper pads, large toys, and other objects that could serve as
steps for climbing out.
Never use this product if there are any loose or missing fasteners, loose joints, broken
parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact
Arm's Reach Concepts, Inc. for replacement parts. Never substitute parts.
NEVER leave child in product with side lowered. Be sure side is in raised and locked
position whenever child is in product.
NEVER use plastic shipping bags or other plastic film as mattress covers not sold and
intended for that purpose. They can cause suffocation.
NEVER use a water mattress with this product.
If refinishing, use a nontoxic finish specified for children's products.
®
sleeper as well as the bassinet or play yard modes, or both.
the adult bed, the top rail must be no higher than the adult bed mattress.
Assemble product according to manufacturer's instructions for ANY use mode—bedside
To avoid death from the infant's neck being caught on the top rail on the side that is next to
Never permit bedding from the adult bed to extend into the Bedside Sleeper.
3

4
NEVER leave child in this product without TOP HORIZONTAL RAIL installed in the
uppermost position, unless the product is in bedside bassinet configuration with the
lowered rail at the same level or lower than adult mattress and the parent/caregiver is
in the adult bed. The product must be secured tightly to the adult bed with the strap and
anchor plate provided.
STRANGULATION/SUFFOCATION HAZARD: The top edge of the lowering rail must be
level with or below the top of the adult mattress when used in the bedside bassinet mode.
The level of this product mattress must be a minimum of 4 inches below the top edge of
the lowering rail. Never raise the product's mattress to be level with, or above the top of
the lowered rail.
NEVER USE the product in bedside bassinet mode without the anchor plate attached
and locked as shown on page 9 and label inside product pocket's. Failure to use this
anchoring system could result in serious injury or death to the infant. Make sure all
straps are secured and tight against adult bed mattress. Check straps before each use.
Failure to use this securing system against adult bed mattress will allow the product to
move away from adult bed and could result in infant falling out of the product. NEVER
leave infant unattended in this product.
To prevent serious or fatal injury from falls always, keep child within arm's reach. Never
leave your child unattended.
Maximum weight capacity for each pocket is 4 lbs. (2 kgs). Do not overfill.
Do Not remove warning labels.

Parts List
A. Fitted Sheet 1 pc
5
B Mattress 1 pc.
C Mattress Support Bars 4 pcs.
(Provides flatness)
Frame
D. Plastic Receiver
E. Mattress Support-straps
(Prevents Sagging)
F. Plastic Connector
G. Lowering Rail
H. Foot strap
I. Removable sleeping nest bottom 1pc
J. 2 Inch Leg Increments 3 pcs
K .Wheels 2 pcs
L. Carry Bag 1 pc
M. Anchor Plate and Strap 1 pc

WARNING: Failure to follow these warnings and
instructions could result in serious injury or death.
Step 2
Note: Center of floor MUST be raised for top rails to lock.
Lock all top rails in place by pulling up on the center of each
rail.
They should be rigid when they are all locked.
Step 3
Push down the center of floor through the hole on zippered
removable sleeping nest bottom (I), allowing bassinet to spread
out and lock. Check that top rails are securely locked in position
until you hear it click into place and push down gently.
How to set up the Arm's Reach Co-Sleeper bedside bassinet
®®
Step 1
Remove product from the carry bag (L).
Undo the Velcro straps of mattress (B).
Set mattress aside.
®
Step 4
Note: Do not forget to install the leg increment of the
middle leg.
Install the wheels and leg increments as figure shown.
Step 5
Install Mattress Support Bars (C) in fabric tunnels on the
nest floor. Place sheet (A) on mattress (B) and lay mattress
into sleeping nest.
The sheet (A) and sleeping nest bottom have Velcro tabs
underneath that align for added security.
It is in Co-Sleeping position now. Go to page 9 to attach the
bedside bassinet to adult bed.
®
6
!WARNING: SUFFOCATION HAZARD - To help
prevent suffocation and entrapment, use ONLY the mattress
pad provided by Arm's Reach Concepts, Inc. NEVER use
additional padding or mattress. DO NOT use shipping or other
bags as mattress covers since they can cause suffocation.

How to set up as freestanding bassinet
FALLING HAZARD:!Remove infant from this
product before starting any conversions.
Step 1
Note: The left and right side plastic connector pieces
must be slide upward at the same time, so that the
lowering rail (G) can be raised smoothly.
Release 4 mattress support-straps (E) that go over the
lowering rail.
Insert foot into the red foot strap under the center of front
bottom, find the locking button under the plastic connectors
(F) on the left and right sides, press them upward to unlock
and slide the lowering rail (G) upward until you hear a "click"
and they are locked in place automatically.
Step 2
Insert the buckles of the mattress support-straps (E) into
hidden pockets.
7
Attach the Velcro on the inside of the lowering rail as
picture.
®
It is in freestanding bassinet now.

How to convert to the co-sleeping position from the freestanding bassinet
FALLING HAZARD:Remove infant from this
product before starting any conversions.
Note: The left and right side plastic connector pieces
must be slid down at the same time, so that the top
rail can be lowered smoothly.
WARNING: THIS STEP PREVENTS THE
MATTRESS FROM SAGGING. Make sure the 4
buckle-straps are connected over the lowered
rail, so the mattress support floor can be taut
and even.
Step 1
Find the locking button under the plastic connectors on the
left and right sides, press them upward to unlock and slide
down the top bar until you hear a "click" and they are locked
in place automatically.
Step 2
Pull out buckles of mattress support-straps (E) from the
pockets. Pull strap up and over lowering rail (G) and connect
on front of lowering rail (G).
8
WARNING: STRANGULATION/SUFFOCATION
HAZARD:The top edge of the lowering rail must be level
with or below the top of the adult mattress when used in
the bedside bassinet mode. The level of this product
mattress must be a minimum of 4 inches below the top
edge of the lowering rail. Never raise the product's
mattress to be level with, or above the top of the lowered
rail.
4'' minimum4'' minimum
It is now in Co-Sleeping position.

WARNING:
WARNING :STRANGULATION/ CHOKING HAZARD
DO not allow excess strap (or any other loose object) to find it's way into this product. Do Not allow excess
strap to lay loose on floor because someone may trip over it.
WARNING: Failure to use this securing system will allow the product to move away from the
adult bed and could result in infant falling out of the product. NEVER leave infant unattended in this
product.
NEVER USE the product in bedside bassinet mode without the anchor plate and
strap (M) attached to the adult bed. Failure to use this anchor plate and strap could result in serious
injury or death to the infant. Make sure all anchor straps are secured and tight. Check straps before
each use.
UNACCEPTABLE BED,
MATTRESS,BOXSPRING&FRAME NOT IN-LINE
Frame Extended
ACCEPTABLE BED FRAME IN-LINE
Mattress, Boxsprings &
Frame aligned
Never use the
co-sleeping position without the anchor
plate and securely attached to the adult bed.
Arm's Reach Co-Sleeper bedside
bassinet in
®®
Loop
Buckle
9
The top edge of the LOWERING RAIL when used in co-sleeping position must be level with or below the top
of adult mattress.
Measure adult bed from floor to top of mattress. If measurement is more than 24", a leg extension kit will be
needed to ensure proper height and maintain safety. 1 Leg Extension Kit will raise the Co-Sleeper up to 6
additional inches in 2" increments accommodating beds 26", 28" and 30". NEVER use more than 1 extension
kit. Do not use leg extensions when the product is NOT attached to the adult bed.
Slide the anchor plate and straps under the mattress, placing the anchor plate flush against the mattress on
the opposite side from this product.
Connect both straps to each short side of the bassinet by passing the male buckle through the “belt loop” at
the front leg of the product and then connect the buckle to rear leg.
Make both straps as tight as possible against the parental bed, so tight it creates a slight indentation in
mattress. To test if the product is tightly secured to adult bed, push it with hands to make sure the gap is no
more than ½”(13mm). If more than ½”(13mm), readjust strap to pull tighter.
When bassinet is tight and ready to use, roll the excess strap up and secure it with elastic loop.
Always tighten straps before each use.
®
It is recommended to make the strap shorter than the width of the mattress to ensure the Co-Sleeper
is pressed securely against the parental bed, without any gaps.
®
9
How to attach the Arm's Reach Co-Sleeper bedside bassinet to adult bed
®®

FALLING HAZARD: Remove infant from this
product before starting any conversions.
Step 2
Remove the sleeping nest bottom by releasing the small
buckle at the end of zipper pull, the zipper around and the
buckles on the back of the sleeping nest.
2
3
1
Step 3
Cover mattress with fitted sheet, feeding Velcro tabs found
on corner ends of mattress thru buttonholes in sheet corners.
Place in bottom of play yard with Velcro tabs extended.
Feed Velcro tabs thru corresponding buttonholes in floor of
play yard corners and secure Velcro tabs around bottom
tube as shown in drawing.
®
®
®
®
10
How to convert to the play yard from the freestanding bassinet
Step 1
Remove the mattress with sheet and mattress support
bar from the freestanding bassinet.

How to fold the play yard
STRANGULATION HAZARD!:When anchor plate and
strap assembly are not in use, store in a safe place not accessible
to children.
Step 1
Remove mattress (B) and set aside.
Hold the webbing handle strap on the center of bottom and pull up.
Cleaning and Maintaining
Spot clean with soft clean damp cloth.
Laundering fitted sheet: Machine wash on lukewarm setting and
drip-dry.NO BLEACH.
Step 2
Unlock short top rails by raising center lock slightly, push on button
of center locks and lower top rails. Repeat steps on top rails on long
sides.
Step 3
Lift up the webbing handle strap of the bottom and push the corner
posts together until the corner posts are straight up and down and
top corner brackets contact each other.
Step 4
Remove sheet (A) off the mattress (B) and wrap the mattress around
the unit. There are Velcro straps that feed through plastic loops
attached to the back side of the mattress. Pull taut. Store the sheet
in the end of the unit.
®
Step 5
Put into carry bag (L) with the handle from the mattress (B) coming
through the opening in the bag.
1
2
11

Q.
A. 1. Locate the floor-lock handle in center of the floor and lift it up as far as possible.
2. Lift top rails up to lock in place.
If you have any question or need further assistance, please call [phone] (US Only ) or
[phone].
For more trouble shooting visit our website at www.armsreach.com
“Top rails can't be unlocked?”
A. All top rails MUST be straight and locked before using. Push the top rails downward to try out if
they are locked.
B. Do not push center floor down until all four top rails are locked.
C. To fold in bassinet mode, reach through hole and pull up on floor lock.
D. When the 2” short segments need to be used on product, make sure all five segments are
assembled on, DO NOT miss the one for the center bottom leg.
E. Remove your finger from the button when the male gliding receiver is unlocked already and start
to glide. Keep pressing it at the top and bottom lock position will prevent the male receiver from
locking into the place.
Visit our website www.armsreach.com for video tutorials under the Assembly Instructions link.
You can also search You Tube for Arm's Reach Co-Sleeper for video tutorials.
®®
Important Assembly Instruction
12

© ARM'S REACH CONCEPTS INC. ARM'S REACH , CO-SLEEPER , and Mother & Child Logo
are Trademarks of ARM'S REACH CONCEPTS INC. All rights reserved.
© ARM'S REACH CONCEPTS INC. ARM'S REACH , CO-SLEEPER et le logo de la mère avec
l'enfant sont des marques commerciales de la société ARM'S REACH CONCEPTS INC. Tous droits
réservés.
©2 ARM'S REACH CONCEPTS INC. ARM'S REACH , CO-SLEEPER , y el logotipo de la madre
con su hijo son marcas comerciales de ARM'S REACH CONCEPTS INC. Reservados todos los
derechos.
®®
®®
®®
2016
Meet ASTM F2194, F2906,
F406 requirements. Patented and patent pending. ARC 12-2016
2016
Répondre aux normes ASTM F2194, F2906, F406 exigences. Breveté et brevet en
instance. ARC 12-2016
016
Conocé ASTM F2194, F2906, F406 requisitos. Patentada y pendiente de patente.
ARC 12-2016