Artison Nano Backpack P5 User manual

Nano Backpack P5 Quick Reference Guide | 009-1947-02 45 Perseverance Way, Hyannis, MA 02601
Copyright 2022 Savant Systems, Inc | 220310 1 of 2 www.savant.com/artisonspeakers | 508.683.2500
Nano Backpack P5 [NANO-BP-P5] Quick Reference Guide
Product Contents
(1) Backpack P5 Source Control (NANO-BP-P5)
(1) AC Cord
(2) Mounting Brackets
(1) IR Receiver
(1) IR Remote
(1) 10 Position screw down connector
(4) M4x10mm screws with washers and star lock nuts
(1) Regulatory and Product Documentation Insert (009-1730-xx)
Video (Supports pass-through of the following):
HDR (Dolby Vision) Supported
Supported
Formats
640x48051280x72051920x12005
720x48051280x102453840x21601
720x57641920x108013840x21602
800x60051920x108033840x21603
1024x76851920x108043840x21604
1280x72041920x108053840x21605
1 = at 24Hz 3 = at 30 Hz 5 = at 60Hz
2= at 25 Hz 4 = at 50 Hz
Minimum Supported Release
Savant OS da Vinci 8.7
Audio
–Stereo and Multi Channel PCM
–Dolby Digital 2.0 Note: For Neo 6, Cinema and
Music will not support sample rate
at 88.2 kHz and 96 kHz input, it
can only support 44.1 kHz and 48
kHz input.
–Dolby Digital 5.1
–DTS Digital Surround (5.1 ch)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40°C)
Humidity 10% to 80% (non-condensing)
Dimensions and Weights
Height Width Depth Weight
Backpack 1.19 in
(3.02 cm) 11.75 in (29.84 cm) 11.625 in (29.53 cm) 4.40 lbs (2.00 kg)
Shipping 5.25 in
(13.34 cm) 15.00 in (38.10 cm) 16.14 in (41.00 cm) 7.10 lbs (3.22 kg)
Power Requirements
Power - Input 120 - 240V AC, 50/60 Hz
Current (Max) 2A
Standards
Wireless Wi-Fi (802.11 b/g/n) | (2.4 | 5.8 Ghz)
Security WPA™, WPA2™, WPA/WPA2, WEP
Bluetooth Bluetooth v4.0 (A2DP, AVRCP, SBC)
A
AC power input. The AC power input accepts the following:
–100 - 120V AC @ 60Hz
–220 - 240V AC @ 50Hz
Use only the power cord included with the Nano Backpack. Not
using an Artison approved power cord can void the warranty.
BPower switch to toggle the Backpack On and O.
C
Five separate speaker level outputs. Wires from speakers are
inserted into a screw-down plug in connector. Speaker outputs are
as follows (4-8 Ω):
–(3) 50W outputs @ .02% THD - 4Ω(Left, Right, Center)
–(2) 25W outputs @ .015% THD - 4Ω(Sur Left, Sur Right)
D
Single Low Frequency Eects (LFE) output. Connect a single
RCA-to-RCA cable from the LFE output port on the Backpack to
the LFE input port on a subwoofer.
E
10/100 Base-T auto negotiating LAN port with activity LEDs.
Link
O - Link not established or in Blackout Mode
Green Solid - Ethernet link established
Green Blinking - Ethernet activity occurring
Activity O - 10 Mbps data rate trac or in Blackout Mode
Amber - 1000 Mbps data rate
FUSB Power - 5V DC, 1A
G(3) HDMI 2.0b compliant
– HDCP 2.2 – Up to 4K@60Hz/4:4:4 – 3D
H
(1) HDMI 2.0b compliant
– HDCP 2.2 – Up to 4K@60Hz/4:4:4 – 3D
– CEC – ARC
I
IR Sensor - Connect the included IR Receiver cable to this port
when Backpack is located in a remote location. See the IR sensor
section below.
AUX - 1 x 3.5mm mini-jack stereo input. Allows for the input of an
analog device using an analog patch cable (3.5mm stereo mini-
jack to RCA patch cable not included).
J
Optical (digital optical input) - Input for a digital source device.
When multichannel audio is input (digital bit stream), the
Backpack decodes the audio to playback surround sound.
Regulatory
Safety and
Emissions
FCC Part 15 CE Mark C-Tick UKCA ETL
Contains FCC ID: 2ADBM-LS9AD-AC11DBT
Contains IC: 7756A-LS9ADBT
RoHS Compliant
Front and Back Panel Descriptions
VOLUME
SOURCE DLNA HDMI 1 HDMI 2
HDMI 3 TV(ARC) OPTICAL AUX BT
B
C
A
A
Multi-function switch selector button. Pressing button will:
Press and release - Cycle between the volume and source.
Press and hold (10 secs) - Puts Backpack in to standby. Press then
release to take out of standby.
BVolume Twist button clockwise or counterclockwise to
increase or decrease volume.
CSource
Twist button clockwise or counterclockwise to scroll
through each port. Fuscia indicates the port that is
selected.
Optional Accessories (sold separately)
–Universal Mounting Bracket for Flat Panel TV (CMP-XL)
–HDMI 2.0 Cable (CBL-HDMI2xxx)
HDMI IN
USB POWERETHERNET
LFE
OUTPUT
L
ON
OFF
AC 100-120V~60Hz.
220-240V~50Hz 200W POWER _ _ _ _ _
RCSL SR HDMI OUT IR SENSOR
OPTICAL
AUX IN
(ARC)
123
5V 1A
+++++
A B C D E F G H I J

Nano Backpack P5 Quick Reference Guide | 009-1947-02 45 Perseverance Way, Hyannis, MA 02601
Copyright 2022 Savant Systems, Inc | 220310 2 of 2 www.savant.com/artisonspeakers | 508.683.2500
Speaker Outputs
A ten position screw-down plug-in connector is supplied for making
connections to any of the five supported speakers. The diagram below
shows how to make connections.
L Wire to + and - terminals of left
channel speaker in a surround
system.
-
SL SRCR
+-
+-
+-
+-
+
L
IMPORTANT!
Observe polarity
when making speaker
connections!
R Wire to + and - terminals of right
channel speaker in a surround
system.
C Wire to + and - terminals of center
channel speaker in a surround
system.
SL Wire to + and - terminals of surround
left channel speaker in a surround
system.
SR Wire to + and - terminals of surround
right channel speaker in a surround
system.
Making Connections
When connecting wires to the 10 position screw-down connector,
follow the guidelines set below to ensure a safe and secure
connection.
1. With a small slotted screwdriver,
turn the screws on connector
counterclockwise (CCW) until silver
crimp opens enough to slide wire(s)
into square slots.
2. Strip insulation from wire so there is
1/4 inch (6.35 mm) of bare wire. Insert
the stripped wire into the proper
connection.
3. Insert wire and turn screws clockwise
(CW) until the crimps tighten around
each wire. Tug on each wire a bit to
ensure a secure connection.
HELPFUL!
– #16 AWG is recommended for lengths up to 50 feet.
– #14 AWG is recommended if wire length is longer than 50 feet
but less than 100 feet.
– #12 AWG is recommended if wire length is longer than 100 feet
but less than 300 feet.
Trademark Information
Dolby, Dolby Digital decoding, Dolby Pro
logic II, and the double-D symbol are
trademarks of Dolby Laboratories.
For DTS patents, see http://patent.
dts.com. Manufactured under license
from DTS, Inc. DTS, the Symbol, DTS
in combination with the Symbol, and
DTS Digital Surround, DTS Neo:6; are
registered trademarks of DTS, Inc. in the
United States and/or other countries.
© DTS, Inc. All Rights Reserved.
Additional Information
Refer to the following documents located on the Savant Customer
Community for additional, information.
–Artison Nano Backpack P5 Deployment Guide (009-1778-xx)
LFE Output
The LFE port (Low Frequency Eects) accepts a standard RCA cable
and connects to the LFE input on a subwoofer speaker.
LFE
OUTPUT
To
Subwoofer
IR Sensor
The IR Sensor connection should be used when access to the front
panel on the Backpack is obstructed. Ensure the receiver side of the
IR cable is mounted where the Backpack IR remote has a direct line of
sight to it.
The IR Sensor input can also be connected to a 3rd party control
system. A cable that connects between the 3rd party controller and
Backpack would be needed.
IR Sensor
3.5 mm stereo
mini-jack
Backpack IR Remote
HDMI IN (1, 2, 3)
Receives and transmits HDMI signaling. Connect HDMI cable between
the Backpack and an external audio/video device such as Apple TV,
ROKU, DVD player, TV. Refer to table on page 1 for supported formats.
HDMI IN
321
To an HDMI
supported device
HDMI OUT
HDMI port that supports ARC (Audio Return Channel), and CEC
(Consumer Electronics Control). ARC allows for downstream of audio
and +CEC signals from the Backpack to the TV. Between ARC and
CEC, one remote can be used to control all devices.
HDMI OUT
(ARC)
To ARC and CEC
supported devices
AUX IN
The AUX In port is an input port and accepts a simple analog audio
connection using an auxiliary cable that incorporates a 3.5 mm stereo
jack.
AUX IN
3.5 mm stereo
mini-jack
Any source device that has an
analog output for audio
OPTICAL
The Optical port is an input port and accepts a digital audio
connection using a fiber optic (TOSLINK) cable.
OPTICAL
To device with optical
output connection
< 1/8 inch
bare wire
exposed
There should be no
more than 1/8 inch of
bare wire exposed from
rear of connector.