AsiaRF AWUHG2402 User manual

High Radio Power USB Adaptor AWUHG2402
User’s Manual
www.asiarf.com 0
USER’S MANUAL
Version 1.0
High Radio Power USB Adaptor AWUHG2402

High Radio Power USB Adaptor AWUHG2402
User’s Manual
www.asiarf.com 1
Trademarks
Copyright @2006
Contents are subject to change without notice.
All trademarks belong to their respective proprietors.
Copyright Statement
THIS DOCUMENT CONTAINS OF PROPRIETARY TECHNICAL INFORMATION THAT IS THE
PROPERTY OF THIS COMPANY. AND NO PART OF THIS DOCUMENTATION MAY BE
REPRODUCED, STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY
MEANS, ELECTRICAL OR MECHANICAL, BY PHOTOCOPYING, RECORDING, OR OTHERWISE,
WITHOUT THE PRIOR WRITTEN CONSENT OF THIS COMPANY.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

High Radio Power USB Adaptor AWUHG2402
User’s Manual
www.asiarf.com 2
Features:
IEEE 802.11b/g Compliant
USB 1.1/2.0 Interface and USB Bus Power
4 dBi high gain Omni-directional antenna
High Radio Power: 17dBm for 802.11g, 20dBm for 802.11b
Compatible with Windows 2000/XP
Plug-and-Play
Works with all standard internet applications
Window Mounting/Desktop Mounting
Benefits:
Long-range through higher gain antenna and higher RF power,
typical twice distance compared with traditional client devices
Easy wireless connection through USB Port
High-Speed Data Rate of Up to 54Mbps
Reduces networking costs
Automatic Fall-Back
Specification:
Model No AWUHG2402
Standard IEEE 802.11b / IEEE 802.11g
Signal Type DSSS (Direct Sequence Spread Spectrum) / OFDM
Modulation BPSK / QPSK / CCK / QAM
Host Interface MINI USB 1.1/2.0
Antenna 4 dBi Omin-directional antenna
Data Encryption 64 / 128 bit WEP/ WPA
Frequency band 2.4 GHz ~ 2.4835 GHz
Channel
11 Channels (US, Canada)
13 Channels (Europe)
14 Channels (Japan)
Data Rate Up to 54Mbps(with Automatic Scale Back)
Transmit Power Output 11b: 20 dBm , 11g: 17dBm (Typical)
Receive Sensitivity 11b: -85 dBm@11Mbps, 11g: -72 dBm@54Mpbs (Typical)
Range 11b: 2km, 11g: 1km (Line-of-sight)
Compatibility Windows 2000/XP
LED Indicators Power, Link Status
Power 5V DC, 450mA Tx, 370mA Rx, 30mA Power-saving Mode
Temperature Operating : 0 to 55℃℃
Storage : -20 to 70℃℃
Humidity 95% Non-Condensing
Certification FCC, CE
USB Cable 4M

High Radio Power USB Adaptor AWUHG2402
User’s Manual
www.asiarf.com 3
Installation Step:
1. Insert Product CD-ROM, the menu appears automatically.
2. Click “DRIVER” to install.
3. The main installation page is showed up. Click “Next” to next step.
4. Takes few minutes during the installation.
5. When the installation page come out “The installation is done.”. Click
“Finish” button and then connect High Radio Power USB Adaptor
AWUHG2402 to USB port of your computer.
6. The computer desktop shows Wireless Application icon after the driver
installed.
7. The small icon will be showed “On-line” on the desktop in the situation line
when AWUHG2402 connected to the USB port of your computer.
8. The small icon will be showed “Off-line” on the desktop in the situation line
when AWUHG2402 was removed from your computer.
Utility Program
Once the driver installed, the utility program installed in the same time is ready
for further management of AWUHG2402.
To execute the program, there are two ways.
1. Click the Wireless Application small icon on the desktop in the situation
line.
2. Click Start / Programs / 802.11g USB Wireless LAN / 802.11g USB /
RAConfig2500.exe.
3. In the management page, click “Status” button to browse the wireless
network information.
4. Click “Wireless AP” to browse the active AP.
5. Click “Statistic” to realize more information of data transferring.