Asko ODV8128G/VS140 User manual

Instructions for use
vacuum drawer
ODV8128G / VS140
ODV8127A / VS140
ODV8127S / VS140

Pictograms used
Important information
Tip

EN 3
CONTENTS
Introduction 4
Description and use
Description 5
Control panel 5
Operation 6
Vacuuming 7
External vacuuming 8
Vacuuming failure 8
Start Dry Run Function 9
Maintenance and cleaning 10
Installation
General 11
Connection 11
Building in 12
Your appliance and the environment
Disposal of the appliance and packaging 13

EN 4
INTRODUCTION
Congratulations on choosing this appliance. This product is designed
with simple operation and optimum comfort in mind.
Read this manual to learn how to get the most out of your appliance. In
addition to information about operating the appliance, you will also find
background information that may be useful when using the appliance.
Read the separate safety instructions before
using the device!
Read this manual before using the appliance and keep it in a safe place
for future use.
Before first use
Make sure that during installation, the transport cover was removed, the
oil filter was installed and that the appliance was mounted according to
the installation instructions.

EN 5
DESCRIPTION AND USE
Description
1. Lid
2. Vacuum chamber
3. Suction point
4. Control panel
5. Hose for external vacuuming
6. Vacuum sealer bag
7. Sealing strip
Control panel
8 12 13 14 159 10 11
8. On/Off touch key
9. Vacuum Level touch key
10. Sealing Time touch key
11. External Vacuum Level touch key
12. Start touch key
13. Stop touch key
14. Dry Run Function touch key with indicator
15. Vacuuming Failure indicator
1
2
4
5
3
7
6

EN 6
DESCRIPTION AND USE
Operation
Operate the vacuum drawer with the control panel on the top of the
drawer.
1. Push the drawer in somewhat and slide it out of the cupboard.
2. Switch on the drawer with the On/Off touch key. Press the On/Off
touch key until the device is switched on.
3. Open the lid and place a vacuum sealer bag in the vacuum
chamber (see ‘Positioning a vacuum sealer bag’).
4. Close the lid.
5. Set the vacuum level with the Vacuum Level touch key
(see ‘Vacuuming’).
The 3 indicator lights display the vacuum level.
The lights flash and diminish during vacuuming.
6. Set the vacuum closure time (sealing time) with the ‘Sealing Time’
touch key (see ‘Vacuuming’).
The 3 indicator lights display the sealing time.
The lights flash and diminish during sealing.
7. Press the Start touch key to start the vacuuming process.
8. Immediately afterwards, shortly press on the front of the lid so
that the vacuum chamber can vacuum.
Note! Vacuuming only works if the lid on the front is quickly pushed into
the rubber gasket!
yVacuuming stops automatically if the vacuum sealer bag has been
vacuumed and sealed.
yOrange indicator lights and orange lighted keys mean that a
function is active.
yWhite indicator lights display the chosen setting and white lighted
keys may be operated.

EN 7
DESCRIPTION AND USE
Vacuuming
Positioning a vacuum sealer bag
2cm
1. Open the lid and place the vacuum sealer bag with the food in the
vacuum chamber.
2. Place the opening of the bag at least 2cm outside the sealing strip.
Note! The bag may not cover the suction point in the vacuum chamber!
Vacuuming
yPress the Vacuum Level touch key a number of times to select a
vacuum level. The white indicator lights display the level.
Select from 3 vacuum levels:
▷Low: for delicate products (bread, soft fruit/vegetables)
▷Middle: for soft products (liquids, fish, prepared products)
▷High: for firm products (firm vegetables, meat, dry products)
yPress the Sealing Time touch key a number of times to select a
closure time (sealing time). Select from 3 sealing times. The proper
sealing time depends on the thickness of the vacuum sealer bag.
The white indicator lights display the level.
Select from 3 sealing times:
▷Thin vacuum sealer bags
▷Medium vacuum sealer bags
▷Thick vacuum sealer bags

EN 8
DESCRIPTION AND USE
External vacuuming
1. Press the On/Off touch key until the device is switched on.
2. Use the included hose to connect the external vacuuming
accessory with the connection point in the vacuum chamber.
3. Use the External Vacuum Level touch key to select a low, middle or
high level.
4. Press the Start touch key to start the vacuuming process.
Vacuuming stops automatically when the vacuum level has been
reached.
Note! Fittings to connect external vacuuming accessories to the hose
for use in external vacuuming are not included with the vacuum drawer.
These are dependent on the type of vacuuming accessory.
Vacuuming failure
If the vacuum drawer cannot vacuum the vacuum chamber, this can be
caused by the following issues:
yThe lid is not or insufficiently pushed in when starting vacuuming.
The Vacuuming Failure indicator lights up.
▷Push the lid on the front into the rubber gasket properly.
yThe oil of the vacuum pump necessary for vacuuming contains
moisture.
The Vacuuming Failure indicator and the Dry Run Function indicator
light up.
▷Start the Dry Run Function*.
yA failure has occurred.
▷Call a service organisation.
* If the vacuuming fails a number of times, then the Vacuuming Failure
indicator and the Dry Run Function indicator light up. It is then advised
to perform the Dry Run Function.
Note! If the Vacuum Failure indicator and Dry Run Function indicator are
ignored, the drawer can no longer be operated after a certain number of
warnings (except the Dry Run Function). It is then necessary to start the
Dry Run Function to be able to use the drawer again.

EN 9
DESCRIPTION AND USE
Starting Dry Run Function
After using the vacuum drawer for a period of time, there will be
moisture in the oil of the vacuum pump. Because of this, the device
may vacuum insufficiently. It is then advised to perform the Dry Run
Function. If vacuuming does not work, then the Vacuuming Failure
indicator and the Dry Run Function indicator light up. After a number of
warnings (Vacuuming Failure indicator and Dry Run Function indicator
lighting up), it is advised to perform the Dry Run Function.
1. Press the Dry Run Function touch key to start the Dry Run Function.
2. Immediately afterwards, shortly press on the front of the lid so that
the vacuum chamber can vacuum.
The Dry Run Function symbol flashes during drying.
Note! If the Dry Run Function does not completely remove the
moisture from the oil after a maximum of 20 minutes, then the drawer
switches to a ‘cool off’ setting. The vacuum drawer can then not be
used for a period of one hour. The Dry Run Function indicator is visible
in the display. After that, start the Dry Run Function again!
Regular use of the Dry Run Function is part of the normal operation
of the vacuum drawer.

EN 10
MAINTENANCE AND CLEANING
Disconnect the appliance before starting with cleaning.
All surfaces should be cleaned only with a damp cloth and some soapy
water. Then dry with a soft cloth.
Do not use a steam cleaner to clean the appliance.
Using abrasive products, alcohol or solvents is not recommended;
these can damage the appliance.
The front is stainless steel or glass and is susceptible to scratching. Use
special non-abrasive cleaning products suitable for stainless steel.
The vacuum chamber can be cleaned with warm water and washing-up
liquid. Then dry with a soft cloth. Avoid to moisten the suction point!

EN 11
INSTALLATION
General
This appliance should be connected to the mains power by a registered
fitter, who knows and applies the correct safety specifications.
Connection
Electrical connection
This appliance is manufactured in Class I; this means the device must
be grounded.
Check whether the power of the electrical mains corresponds to the
power on the identification plate on the appliance.
Before connecting to the electrical mains, check whether the power
socket is grounded.
The device is equipped with a plug. When installing the appliance,
remember that this plug must remain accessible.
Note!
If you want to make a fixed connection, make sure a multi-polar switch
with a contact separation of at least 3mm is fitted in the supply line.
Install oil filter
yRemove the transport cover
yInstall oil filter

EN 12
INSTALLATION
Building in
590
597
550
425
135
141
556
min. 550
450
560-568
1. Put the plug of the device in a grounded wall socket.
Slide the appliance in the kitchen cupboard opening. Check
whether the casing fits correctly.
2. Screw the drawer securely to the cupboard at the left and right front
using the 4 screws supplied.
3. Slide the decorative strips over the draw profiles on the left and
right, starting from the top (ODV8128G only).
Note! When sliding out the drawer, it can tip forward if it is not
securely screwed to the kitchen cupboard.

EN 13
YOUR APPLIANCE AND THE ENVIRONMENT
Disposal of the appliance and packaging
This product is made from sustainable materials. However, the
appliance must be disposed of responsibly at the end of its useful life.
The government can provide you with information about this.
The appliance packaging is recyclable. The following materials have
been used:
ycardboard
ypolyethylene wrapping (PE)
yCFC-free polystyrene (hard PS foam)
Dispose of these materials responsibly in accordance with legal
provisions.
The product has a pictogram of a crossed-out waste container. This
indicates that household appliances must be disposed of separately.
This means that the appliance may not be processed via the regular
waste flow at the end of its useful life. You should take it to a special
municipal waste depot or a sales outlet that offers to do this for you.
Collecting household equipment separately prevents harm to the
environment and public health. The materials used in manufacturing
this appliance can be recycled, which provides considerable savings in
energy and raw materials.
Declaration of conformity
We hereby declare that our products comply with the relevant European
directives, standards and regulations as well as all requirements
referred to in the standards.

EN 14

EN 15

713096 / VER1 / 28-02-2018
713096
*713096*