ASROCK H81M-DG6 User manual

Version 1.0
Published August 2014
Copyright©2014 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com

1
English
H81M-DG6
Motherboard Layout
Intel
H81
DDR3_B1 (64 bit, 240-pin module)
DDR3_A1 (64 bit, 240-pin module)
CMOS
Battery
Super
I/O
ATXPWR1
LAN
Top:
RJ-45
USB 2.0
T: USB2
B: USB3
CLRCMOS1
1
1
SPEAKER1
IR1
1
HDLED RESET
PLED PWRBTN
PANEL1
1
USB_2_3
1
COM1
1
1
HD_AUDIO1
H81M-DG6
CHA_FAN1
RoHS
7
8
14
16 12
13
17
19
20
21
18
15
2
CPU_FAN1
3
4
6
5
1
32Mb
BIOS
USB 2.0
T: USB0
B: USB1
Audio
CODEC
PCIE1
1
TPMS1
1
1
LPT1
CI1
9
10
11
SATA3 _0 S ATA2_ 0
PS2
Keyboard
PS2
Mouse
USB 3.0
T: USB0
B: USB1
Top:
LINE I N
Center:
FRONT
Bottom:
MIC IN
ATX1 2V1
USB 3.0
PCIE2
PCI1
SATA3 _1 S ATA2_ 1
1
SPDIF_OUT1
USB_4_5
1
VGA1 DVI1

2
English
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1)
3 ATX Power Connector (ATXPWR1)
4 TPM Header (TPMS1)
5 SATA2 Connector (SATA2_0)
6 SATA2 Connector (SATA2_1)
7 SATA3 Connector (SATA3_1)
8 SATA3 Connector (SATA3_0)
9 System Panel Header (PANEL1)
10 Chassis Intrusion Header (CI1)
11 Chassis Speaker Header (SPEAKER1)
12 Chassis Fan Connector (CHA_FAN1)
13 USB 2.0 Header (USB_4_5)
14 USB 2.0 Header (USB_2_3)
15 COM Port Header (COM1)
16 Print Port Header (LPT1)
17 SPDIF Out Connector (SPDIF_OUT1)
18 Front Panel Audio Header (HD_AUDIO1)
19 Clear CMOS Jumper (CLRCMOS1)
20 Infrared Module Header (IR1)
21 CPU Fan Connector (CPU_FAN1)

3
English
H81M-DG6
I/O Panel
No. Description No. Description
1 PS/2 Mouse Port 7 USB 2.0 Ports (USB_01)
2 LAN RJ-45 Port* 8 USB 3.0 Ports (USB3_01)
3 Line In (Light Blue) 9 DVI-D Port
4 Front Speaker (Lime) 10 D-Sub Port
5 Microphone (Pink) 11 PS/2 Keyboard Port
6 USB 2.0 Ports (USB_23)
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
1 2 4
567891011
3

4
English
Chapter 1 Introduction
ank you for purchasing ASRock H81M-DG6 motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
1.1 Package Contents
• ASRock H61M-DG6 Motherboard (Micro ATX Form Factor)
• ASRock H61M-DG6 Quick Installation Guide
• ASRock H61M-DG6 Support CD
• 2 x Serial ATA (SATA) Data Cables (Optional)
• 1 x I/O Panel Shield
Because the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website without further notice. If you require technical support related to
this motherboard, please visit our website for specic information about the model
you are using. You may nd the latest VGA cards and CPU support list on ASRock’s
website as well. ASRock website http://www.asrock.com.

5
English
H81M-DG6
1.2 Specications
Platform • Micro ATX Form Factor
• Solid Capacitor for CPU power
• High Density Glass Fabric PCB
CPU • Supports New 4th and 4th Generation Intel® CoreTM i7/i5/i3/
Xeon®/Pentium®/Celeron® Processors (Socket 1150)
• Digi Power design
• Supports Intel® Turbo Boost 2.0 Technology
Chipset • Intel® H81
Memory • Dual Channel DDR3 Memory Technology
• 2 x DDR3 DIMM Slots
• Supports DDR3 1600/1333/1066 non-ECC, un-buered
memory
• Max. capacity of system memory: 16GB (see CAUTION)
• Supports Intel® Extreme Memory Prole (XMP) 1.3 / 1.2
Expansion
Slot
• 1 x PCI Express 2.0 x16 Slot (PCIE1: x16 mode)
• 1 x PCI Express 2.0 x1 Slot
• 1 x PCI Slot
Graphics • Intel® HD Graphics Built-in Visuals and the VGA outputs can
be supported only with processors which are GPU integrated.
• Supports Intel® HD Graphics Built-in Visuals : Intel® Quick
Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics 4400/4600
• Pixel Shader 5.0, DirectX 11.1
• Max. shared memory 1792MB
• Dual graphics output: support DVI-D and D-Sub ports by
independent display controllers
• Supports DVI-D with max. resolution up to 1920x1200 @
60Hz
• Supports D-Sub with max. resolution up to 1920x1200 @
60Hz
• Supports HDCP with DVI-D Port

6
English
• Supports Full HD 1080p Blu-ray (BD) playback with DVI-D
Port
Audio • 5.1 CH HD Audio (Realtek ALC662 Audio Codec)
• Supports Surge Protection (ASRock Full Spike Protection)
LAN • PCIE x1 Gigabit LAN 10/100/1000 Mb/s
• Qualcomm® Atheros® AR8171
• Supports Wake-On-LAN
• Supports Lightning/ESD Protection (ASRock Full Spike
Protection)
• Supports Energy Ecient Ethernet 802.3az
• Supports PXE
Rear Panel
I/O
• 1 x PS/2 Mouse Port
• 1 x PS/2 Keyboard Port
• 1 x D-Sub Port
• 1 x DVI-D Port
• 4 x USB 2.0 Ports (Supports ESD Protection (ASRock Full
Spike Protection))
• 2 x USB 3.0 Ports (Supports ESD Protection (ASRock Full
Spike Protection))
• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
Storage • 2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and
Hot Plug
• 2 x SATA2 3.0 Gb/s Connectors, support NCQ, AHCI and
Hot Plug

7
English
H81M-DG6
Connector • 1 x IR Header
• 1 x Print Port Header
• 1 x COM Port Header
• 1 x Chassis Intrusion Header
• 1 x TPM Header
• 1 x CPU Fan Connector (4-pin)
• 1 x Chassis Fan Connector (4-pin)
• 1 x 24 pin ATX Power Connector
• 1 x 4 pin 12V Power Connector
• 1 x Front Panel Audio Connector
• 1 x SPDIF Out Connector
• 2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD
Protection (ASRock Full Spike Protection))
BIOS
Feature
• 32Mb AMI UEFI Legal BIOS with multilingual GUI support
• ACPI 1.1 Compliant wake up events
• SMBIOS 2.3.1 support
• CPU, DRAM, PCH 1.05V, PCH 1.5V Voltage multi-adjust-
ment
Hardware
Monitor
• CPU/Chassis temperature sensing
• CPU/Chassis Fan Tachometer
• CPU Quiet Fan (Auto adjust chassis fan speed by CPU tem-
perature)
• CPU/Chassis Fan multi-speed control
• CASE OPEN detection
• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore
OS • Microso® Windows® 8.1 32-bit / 8.1 64-bit / 8 32-bit / 8 64-
bit / 7 32-bit / 7 64-bit
Certica-
tions
• FCC, CE, WHQL
• ErP/EuP ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com

8
English
Please realize that there is a certain risk involved with overclocking, including adjust-
ing the setting in the BIOS, applying Untied Overclocking Technology, or using third-
party overclocking tools. Overclocking may aect your system’s stability, or even cause
damage to the components and devices of your system. It should be done at your own
risk and expense. We are not responsible for possible damage caused by overclocking.
Due to limitation, the actual memory size may be less than 4GB for the reservation
for system usage under Windows® 32-bit operating systems. Windows® 64-bit operat-
ing systems do not have such limitations. You can use ASRock XFast RAM to utilize
the memory that Windows® cannot use.

9
English
H81M-DG6
Clear CMOSDefault
1.3 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper
(CLRCMOS1)
(see p.1, No. 19)
CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power
cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear
the CMOS right aer you update the BIOS. If you need to clear the CMOS when
you just nish updating the BIOS, you must boot up the system rst, and then shut
it down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default prole will be cleared only if the CMOS battery is
removed.

10
English
1.4 Onboard Headers and Connectors
System Panel Header
(9-pin PANEL1)
(see p.1, No. 9)
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may congure the way to
turn o your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart
the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. e LED is on when
the system is operating. e LED keeps blinking when the system is in S1/S3 sleep state.
e LED is o when the system is in S4 sleep state or powered o (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. e LED is on when
the hard drive is reading or writing data.
e front panel design may dier by chassis. A front panel module mainly consists
of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.
When connecting your chassis front panel module to this header, make sure the wire
assignments and the pin assignments are matched correctly.
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.

11
English
H81M-DG6
Serial ATA2 Connectors
(SATA2_0:
see p.1, No. 5)
(SATA2_1:
see p.1, No. 6)
ese two SATA2
connectors support SATA
data cables for internal
storage devices with up to
3.0 Gb/s data transfer rate.
Serial ATA3 Connectors
(SATA3_0:
see p.1, No. 8)
(SATA3_1:
see p.1, No. 7)
ese two SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
USB 2.0 Headers
(9-pin USB_2_3)
(see p.1, No. 17)
(9-pin USB_4_5)
(see p.1, No. 13)
Besides four USB 2.0 ports
on the I/O panel, there
are two headers on this
motherboard. Each USB
2.0 header can support
two ports.
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.1, No. 18)
is header is for
connecting audio devices
to the front audio panel.
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
SATA2_0
SATA2_1
SATA3_0
SATA3_1
1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must
support HDA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.

12
English
Chassis Speaker Header
(4-pin SPEAKER1)
(see p.1, No. 11)
Please connect the chassis
speaker to this header.
SPDIF Out Connector
(2-pin SPDIF_OUT1)
(see p.1, No. 17)
Please connect the
SPDIF_OUT connector of
a HDMI VGA card to this
header with a cable.
Chassis Connector
(4-pin CHA_FAN1)
(see p.1, No. 12)
Please connect fan cable
to the fan connector and
match the black wire to
the ground pin.
CPU Fan Connector
(4-pin CPU_FAN1)
(see p.1, No. 21)
is motherboard pro-
vides a 4-Pin CPU fan
(Quiet Fan) connector.
If you plan to connect a
3-Pin CPU fan, please
connect it to Pin 1-3.
ATX Power Connector
(24-pin ATXPWR1)
(see p.1, No. 3)
is motherboard pro-
vides a 24-pin ATX power
connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
13.
ATX 12V Power
Connector
(4-pin ATX12V1)
(see p.1, No. 1)
is motherboard pro-
vides an 4-pin ATX 12V
power connector.
Infrared Module Header
(5-pin IR1)
(see p.1, No. 20)
is header supports an optional
wireless transmitting and
receiving infrared module.
1
+5V
DUMMY
DUMMY
SPEAKER
FAN_SPEED
FAN_SPEED_CONTROL
GND
+12V
1 2 3 4
12
1
24
13
SPDIFOUT
GND
1
FAN_SPEED
FAN_SPEED_CONTROL
+12V
GND 1
2
3
4
IRRX
GND
DUMMY
+5VSB
IRTX
1

13
English
H81M-DG6
Serial Port Header
(9-pin COM1)
(see p.1, No. 15)
is COM1 header
supports a serial port
module.
Chassis Intrusion Header
(2-pin CI1)
(see p.1, No. 10)
is motherboard
supports CASE OPEN
detection feature that
detects if the chassis cove
has been removed. is
feature requires a chassis
with chassis intrusion
detection design.
TPM Header
(17-pin TPMS1)
(see p.1, No. 4)
is connector supports
Trusted Platform Module
(TPM) system, which can
securely store keys, digital
certicates, passwords,
and data. A TPM system
also helps enhance
network security, protects
digital identities, and
ensures platform integrity.
Print Port Header
(25-pin LPT1)
(see p.1, No. 16)
is is an interface
for print port cable
that allows convenient
connection of printer
devices.
CCTS#1
RRTS#1
DDSR#1
DDTR#1
RRXD1
GND
TTXD1
DDCD#1
1
RRI#1
PCIRST#
FRAME
PCICLK
1
AFD#
ERROR#
PINIT#
GN D
SLIN#
STB#
SPD0
SPD1
SPD3
SPD2
SPD4
SPD5
SPD6
SPD7
ACK#
BUSY
PE
SLCT
1
Signal
GND

14
한 국 어
규격
플랫폼 •Micro ATX 폼팩터
•CPU 전원용 솔리드 콘덴서
•고밀도 유리 직물 PCB
CPU •신형 4 세대 및4 세대 Intel® CoreTM i7/i5/i3/Xeon®/Pentium®/
Celeron® 프로세서 (소켓 1150) 지원
•Digi 전원 구조
•Intel®Turbo Boost 2.0 기술 지원
칩세트 •Intel®H81
메모리 •듀얼 채널 DDR3 메모리 기술
•DDR3 DIMM 슬롯 2 개
•DDR3 1600/1333/1066 비-ECC, 비버퍼링 메모리 지원
•시스템 메모리 최대 용량 : 16GB ( 주의 참조 )
•Intel® Extreme Memory Prole (XMP)1.3/1.2 지원
확장 슬롯 •PCI Express 2.0 x16 슬롯 1 개(PCIE1: x16 모드 )
•PCI Express 2.0 x1 슬롯 1 개
•PCI 슬롯 1 개
그래픽 •Intel® HD 그래픽스 빌트 -인비주얼과 VGA 출력은 GPU 통
합프로세서로만 지원할 수있습니다 .
•Intel® HD 그래픽스 빌트 -인비주얼 지원 : AVC, MVC (S3D)
및MPEG-2 풀HW Encode1 지원 Intel® Quick Sync Video,
Intel® InTruTM 3D, Intel® 클리어 비디오 HD 기술 , Intel®
InsiderTM, Intel® HD 그래픽스 4400/4600
•Pixel Shader 5.0, DirectX 11.1
•최대 공유 메모리 1792MB
•더블 VGA 수출 : DVI-D 와D-Sub 포트 독립 디스플레이 컨
트롤러를 지원
•DVI-D 지원 (최대 해상도 1920x1200 @ 60Hz)
•D-Sub 지원 (최대 해상도 1920x1200 @ 60Hz)
•DVI-D 포트를 이용한 HDCP 기능 지원
•DVI-D 포트를 이용한 Full HD 1080p Blu-ray (BD) 재생 지원

15
한 국 어
H81M-DG6
오디오 •5.1 CH HD 오디오 지원 (Realtek ALC662 오디오 코덱 )
•서지 보호 (ASRock 풀스파이크 보호 ) 지원
LAN •PCIE 1 개, Gigabit LAN 10/100/1000 Mb/s
•Qualcomm® Atheros® AR8171
•Wake-On-LAN 지원
•조명 /ESD 보호 (ASRock 풀스파이크 보호 ) 지원
•절전형 이더넷 802.3az 지원
•PXE 지원
후면 패널 I/O •PS/2 마우스 포트 1 개
•PS/2 키보드 포트 1 개
•D-Sub 포트 1 개
•DVI-D 포트 1 개
•USB 2.0 포트 4 개(ESD 보호 (ASRock 풀스파이크 보호 ) 지
원)
•USB 3.0 포트 2 개(ESD 보호 (ASRock 풀스파이크 보호 ) 지
원)
•LED 장착 RJ-45 LAN 포트 1 개(ACT/LINK LED 및SPEED
LED)
•HD 오디오 잭: 라인 입력 / 전면 스피커 / 마이크
저장 장치 •SATA3 6.0 Gb/s 커넥터 2 개, NCQ, AHCI 및“핫플러그”
기능 지원
•SATA2 3.0 Gb/s 커넥터 2 개, NCQ, AHCI 및“핫플러그”
기능 지원
커넥터 •IR 헤더 1 개
•인쇄 포트 헤더 1 개
•COM 포트 헤더 1 개
•섀시 침입 헤더 1 개
•TPM 헤더 1 개
•CPU 팬커넥터 1 개(4 핀)
•섀시 팬커넥터 1 개(4 핀)
•24 핀ATX 전원 커넥터 1 개
•4핀12V 전원 커넥터 1 개
•전면 패널 오디오 커넥터 1 개
•SPDIF 출력 커넥터 1 개

16
한 국 어
•USB 2.0 헤더 2 개(USB 2.0 포트 4 개지원 ) (ESD 보호 지원
(ASRock 풀스파이크 보호 ))
BIOS 기능 •다국어 GUI 지원을 제공하는 32Mb AMI UEFI 적합형 BIOS
•ACPI 1.1 준수 웨이크 업이벤트
•SMBIOS 2.3.1 지원
•CPU, DRAM, PCH 1.05V, PCH 1.5V 전압 다중 조정
하드웨어 모니
터
•CPU/ 섀시 온도 감지
•CPU/ 섀시 팬타코미터
•CPU 저소음 팬(CPU 온도에 의한 섀시 팬속도 자동 조정 )
•CPU/ 섀시 팬다중 속도 조절
•케이스 열림 감지
•전압 모니터링 : +12V, +5V, +3.3V, CPU Vcore
OS •Microso® Windows® 8.1 32 비트 / 8.1 64 비트 / 8 32 비트 / 8
64 비트 / 7 32 비트 / 7 64 비트
인증 •FCC, CE, WHQL
•ErP/EuP 사용 가능 (ErP/EuP 사용 가능 전원공급장치 필요 )
BIOS 설정을 조정하거나 Untied Overclocking Technology 를적용하거나 타업체의
오버클로킹 도구를 사용하는 것을 포함하는 오버클로킹에는 어느 정도의 위험이
따른다는 것을 유념하십시오 . 오버클로킹은 시스템 안정성에 영향을 주거나 심지
어시스템의 구성 요소와 장치에 손상을 입힐 수도 있습니다 . 오버클로킹은 사용자
스스로 위험과 비용을 감수하고 해야 합니다 . 당사는 오버클로킹에 의해 발생할 수
있는 손상에 대해서 책임이 없습니다 .
* 자세한 제품 정보에 대해서는 당사 웹사이트를 참조하십시오 : http://www.asrock.com
제한 때문에 실제 메모리 크기는 Windows
®
32 비트 운영체제 하의 시스템 사용을
위한 예비 메모리용 4GB 보다 더적을 수있습니다 . Windows
®
64 비트 운영체제에
는그러한 제한이 없습니다 . ASRock XFast RAM 을사용하여 Windows
®
가사용
할수없는 메모리를 이용할 수있습니다 .

Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support request
form at http://www.asrock.com/support/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
ASRock EUROPE B.V.
Bijsterhuizen 3151
6604 LV Wijchen
e Netherlands
Phone: [phone]
Fax: [phone]
ASRock America, Inc.
13848 Magnolia Ave, Chino, CA91710
U.S.A.
Phone: [phone]
Fax: [phone]