ASROCK IMB-1713 User manual

IMB-1713
User Manual
Version 1.0
Published March 17, 2023
Copyright©2023 ASRockInd INC. All rights reserved.

Version 1.0
Published March, 2023
Copyright©2023 ASRockInd INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRockInd Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished
for informational use only and subject to change without notice, and should
not be constructed as a commitment by ASRockInd. ASRockInd assumes no
responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRockInd does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRockInd, its directors, ocers, employees, or agents be liable
for any indirect, special, incidental, or consequential damages (including damages
for loss of prots, loss of business, loss of data, interruption of business and the
like), even if ASRockInd has been advised of the possibility of such damages arising
from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
e terms HDMI®and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

WARNING
THIS PRODUCT CONTAINS A BUTTOON BATTERY
If swallowed, a button battery can cause serious injury or death.
Please keep batteries out of sight or reach of children.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRockInd
Tel : [phone] ext.123 (Standard International call charges apply)
ASRockInd INC. hereby declares that this device is in compliance with the essential re-
quirements and other relevant provisions of related UKCA Directives. Full text of UKCA
declaration of conformity is available at: http://www.asrockind.com
ASRockInd INC. hereby declares that this device is in compliance with the essential re-
quirements and other relevant provisions of related Directives. Full text of EU declaration
of conformity is available at: http://www.asrockind.com
ASRockInd follows the green design concept to design and manufacture our products,
and
makes sure that each stage of the product life cycle of ASRockInd product is in line with
global
environmental regulations. In addition, ASRockInd disclose the relevant information
based on regulation requirements.
Please refer to https://www.asrockind.com/general/about.asp?cat=Responsibility for in-
formation disclosure based on regulation requirements ASRockInd is complied with.
DO NOT throw the motherboard in municipal waste. is product has been
designed to enable proper reuse of parts and recycling. This symbol of the
crossed out wheeled bin indicates that the product (electrical and electronic
equipment) should not be placed in municipal waste. Check local regulations
for disposal of electronic products.

Contents
1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 4
1.4 I/O Panel 6
1.5 Block Diagram 7
2 Installation 8
2.1 Screw Holes 8
2.2 Pre-installation Precautions 8
2.3 Installation of Memory Modules 9
2.4 Expansion Slots 11
2.5 Jumpers Setup 12
2.6 Onboard Headers and Connectors 15
2.7 I/O Ports 22
3 UEFI SETUP UTILITY 25
3.1 Introduction 25
3.1.1 Entering BIOS Setup 25
3.1.2 UEFI Menu Bar 26
3.1.3 Navigation Keys 27
3.2 Main Screen (Advanced Mode) 28
3.3 Advanced Screen 29
3.3.1 CPU Conguration 30
3.3.2 Chipset Conguration 33
3.3.3 Storage Conguration 36
3.3.4 Super IO Conguration 38
3.3.5 ACPI Conguration 40
3.3.6 USB Conguration 41
3.3.7 Trusted Computing 42
3.3.8 Thunderbolt (TM) Conguration 44
3.4 Hardware Health Event Monitoring Screen 45
3.5 Security Screen 47

3.6 Boot Screen 48
3.7 Exit Screen 50

1
IMB-1713
Chapter 1 Introduction
Thank you for purchasing ASRockInd IMB-1713 motherboard, a reliable mother-
board produced under ASRockInd’s consistently stringent quality control. It delivers
excellent performance with robust design conforming to ASRockInd’s commitment to
quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-
step guide to the hardware installation. Chapter 3 contains the conguration guide to
BIOS setup.
Because the motherboard specications and the BIOS soware might be updated, the
content of this manual will be subject to change without notice. In case any modica-
tions of this manual occur, the updated version will be available on ASRockInd website
without further notice. You may nd the latest CPU support lists on ASRockInd web-
site as well.
ASRockInd website https://www.asrockind.com/
If you require technical support related to this motherboard, please visit our website for
specic information about the model you are using.
https://www.asrockind.com/support/index.asp
1.1 Package Contents
ASRockInd IMB-1713 Motherboard (ATX (12-in x 9.6-in x 1.4-in, 30.5 cm x 24.4 cm
x 3.6 cm))
• Gi Package
2 x SATA Cable
1 x I/O Shield
1 x SCREW M2*2, D=5
• Bulk Package
1 x I/O Shield
1 x SCREW M2*2, D=5

2
1.2 Specications
Form Factor Dimensions ATX (12-in x 9.6-in x 1.4-in, 30.5 cm x 24.4 cm x 3.6 cm)
Processor
System
CPU Intel® 13th/12th Gen (Raptor Lake-S/Alder Lake-S)
Core™ Processors, up to 125 W
Chipset Intel® H610
Socket LGA1700
BIOS AMI SPI 256 Mbit
Expansion
Slot
PCIe
1 x PCIe x16 (Gen5)
1 x PCIe x4 (Gen3)
1 x PCIe x1 (Gen3)
PCI 4
Memory
Technology
Dual Channel DDR5 5600/4800MHz (Raptor Lake-S),
DDR5 4800 MHz (Alder Lake-S)
- Intel Core i9/i7 CPUs support DDR5 up to 5600
MHz (Raptor Lake-S)
- Intel Core i5/i3/Pentium/Celeron CPUs support
DDR5 up to 4800 MHz (Raptor Lake-S)
Capacity 64GB (32GB per DIMM)
Socket 2 x 288-pin Long-DIMM
Graphics
Controller Intel® UHD Graphics
HDMI HDMI 2.0b
Max resolution up to 4096 x 2160@60Hz
DisplayPort DisplayPort 1.4a, DP++
Max resolution up to 4096 x 2160@60Hz
VGA Max resolution up to 1920 x 1200@60Hz
Multi Display Triple Display
Audio Interface Realtek ALC897, High Denition Audio. Line-In, Line-Out,
Mic-In
Ethernet
Controller/
Speed
LAN1: Realtek® RTL8125BG with 10/100/1000/2500 Mbps,
supports PoE
LAN2: Intel® I219V with 10/100/1000 Mbps
Controller 2 x RJ-45
Rear I/O
HDMI 1 x HDMI 2.0b
DisplayPort 2 x DP 1.4a++
VGA 1
Ethernet 1 x 1 Gigabit LAN
1 x 2.5 Gigabit LAN
USB 2 x USB 3.2 Gen2
2 x USB 2.0
Audio 3 (Line-In, Line-Out, Mic-In)
COM COM1, COM2 (RS-232/422/485)
PS2 1 x PS/2 combo

3
IMB-1713
Internal
Connector
USB
2 x USB 3.2 Gen1 (1 x USB 3.1 header)
3 x USB 2.0 (1 x 2.54 pitch header, 1 x USB 2.0 Type-A
vertical connector)
COM COM3, COM4, COM5, COM6 (RS-232)
Parallel 1 (shared with GPIO)
GPIO 8 x GPI, 8 x GPO (shared with LPT header)
TPM TPM 2.0 onboard IC
Speaker Header 1
Storage M.2 1 x M.2 (Key M, 3042/2260/2280/22110)
with PCIe Gen3 x 1
SATA 4 x SATA3 (6Gb/s)
Watchdog
Timer
Output From Super I/O to drag RESETCON#
Interval 256 Segments, 0, 1, 2, ...255 Sec
Power
Requirements
Input PWR ATX-PWR (24+8-pin)
Power On
AT/ATX Supported
-AT: Directly PWR on as power input ready
-ATX: Press button to PWR on aer power input ready
Environment
Operating
Temp 0ºC - 70ºC
Storage Temp -40ºC - 85ºC
Operating
Humidity 5% - 90%
Storage
Humidity 5% - 90%

4
1.3 Motherboard Layout
ATXPWR1
PCIE1
1
HD_AUDIO1
CMOS
Battery
HDLED RESET
PLED PWRBTN
1
CPU_FAN1
Top:
Line In
Center:
Line Out
Bottom:
Mic In
IMB-1713
ATX12V1
Industrial
1
PWR_LOSS1
1
LPT_GPIO1
JGPIO_SET1
1
1
SPDIF1
1
DDR5_A1DDR5_B1
COM2
VGA1
1
CLRMOS2
CHA_FAN1
PCIE3
1
BUZZ2
PWR_COM3
1
CHA_FAN3
USB2_7_8
1
ESPI1
1
1
USB3_3_4
CHA_FAN2
PWR_COM1
1
M2_M1
Top:
LAN1
USB 2.0
T: USB2_6
B: USB2_5
LAN_LED2
1
LAN_LED1
1
PCI1
TB1
1
BIOS
ROM
PCI2
PCI3
PCI4
PCIE2
PWR_COM2
1
DP2
DP1
COM1
HDMI1
PS2_KB_MS1
Top:
LAN2
USB 3.2 Gen2
T: USB3_2
B: USB3_1
SATA3_1
SATA3_3
SATA3_2
SATA3_4
1
1
COM5
1
COM4
1
COM6
1
PWR_COM5
1
1
PWR_COM6
1
1
Cl1
1
C2l
1
1
DACC1
12 3457
8
9
10
11
6
15
14
13
12
20 19 18 17 16
27
26
25 24 23 22 21
28
29
USB2_9
COM3
PWR_COM4
SIO_AT1
JGPIO_PWR1
PANEL1
CLRMOS1
1
1
1
1
1

5
IMB-1713
1 : Chassis FAN Connector (+12V) (CHA_FAN1)
2 : ATX 12V Power Connector
3 : Chassis FAN Connector (+12V) (CHA_FAN3)
4 : M.2 Key-M Socket (M2_M1)
5 : CPU F AN Connector (+12V)
6 : USB 2.0 Connector (USB2_9)
7 : PWR LOSS Jumper (PWR_LOSS1)
8 : 24-pin ATX Power Input Connector
9 : Chassis FAN Connector (+12V) (CHA_FAN2)
10 : USB 3.2 Gen1 Header (USB3_3_4)
11 : SATA3 Connectors (SATA3_1~SATA_4)
12 : 5-pin underbolt AIC Connector (TB1)
13 : Clear CMOS Headers (CLRMOS1, CLRMOS2)
14 : COM Port Headers (COM3~6) (RS232)
15 : ATX/AT Mode Jumper (SIO_AT1)
16 : Chassis Intrusion Headers (CI1, CI2)
17 : COM Port Pin9 PWR Setting Jumpers
PWR_COM3 (For COM Port3)
PWR_COM4 (For COM Port4)
PWR_COM5 (For COM Port5)
PWR_COM6 (For COM Port6)
18 : Printer Port / GPIO Header (LPT_GPIO1)
19 : ESPI Header
20 : Digital Input / Output Power Select (JGPIOPWR) (JGPIO_PWR1)
21 : Digital Input / Output Default Value Setting (JGPIO_SET1)
22 : USB 2.0 Header (USB2_7_8)
23 : System Panel Header
24 : SPDIF Header
25 : Front Panel Audio Header
26 : Buzzer (BUZZ2)
27 : DACC1
28 : LAN LED Headers
LAN_LED2 (For LAN2 Port)
LAN_LED1 (For LAN1 Port)
29 : COM Port Pin9 PWR Setting Jumpers
PWR_COM1 (For COM Port1)
PWR_COM2 (For COM Port2)

6
1.4 I/O Panel
1 DisplayPort (DP2)
2 Com Port (COM1) (RS232/422/485)*
3 Com Port (COM2) (RS232/422/485)*
4 RJ45 LAN Port (LAN2)**
5 RJ45 LAN Port (LAN1)***
6 Line In (Blue)
7 Line Out (Green)
8 Microphone (Pink)
9 USB 2.0 Ports (USB2_5_6)
10 USB 3.2 Gen2 Ports (USB3_1_2)
11 D-Sub Port (VGA1)
12 PS/2 Keyboard/Mouse Port
(PS2_KB_MS1)
13 HDMI Port (HDMI1)
14 DisplayPort (DP1)
23 1
7
6
8
910
11
13 12
45
14

7
IMB-1713
1.5 Block Diagram
Intel
PCH
H610
Intel
Alder Lake-S
Processor
LGA-1700
DMI
U-DIMM
(A1)
ChannelB DDR5 4800MHzU-DIMM
(A2)
PCIe Gen5 [0:15] PCIe x16 Slot
HDMI
Connector
Display port1
VGA
Connector
ITE
IT66318
DDIB
HDMI
Realtek
RTD2168
DDIE
VGA
DDIC
Channel ADDR5 4800MHz
SATA x4(#17~20) SATA Port x4
FINTEK
F81966
GPIO x4
PCIe x1 (#1)
PCI Slot x4
2x USB2.0 (P5, P6)
UART x2
LPT/DGIO header
COM Port x2
RS232/422/482
UART x4
COM Port x4
RS232 only
LPT/GPIO FAN
Asmedia
ASM1085
PCIe x1 (#15)
2x USB3.2 Gen2
Connector
PI3EQX1004ZHEX
Intel
I219V
MDI 1G
2x USB2.0
Connector
2x USB2.0 (P7, P8)
2x USB2.0
Header
1x USB2.0
Connector
1x USB2.0 (P9)
PCIe x1 (#3)
INFINEON
SLB9670XQ2.0
NUVOTON
NUC121ZC2AE
SMBUS
CPU FAN x1
CHAISS FAN x1
PS/2 KB, MS PS/2 Combo
Connector
CHAISS FAN x2
Display port2DDID
PCI x4 (#1~4)
PCIe x1 Slot PCIe x1 (#2)
PCIe x4 Slot PCIe x4 (#5~8)
2xUSB3.2 Gen2(#1, #2)
2x USB2.0(P1, P2)
2xUSB3.2 Gen2(#1, #2)
RJ45
Connector
Realtek
RTL8125BG
MDI 2.5G
RJ45
Connector
(PoE 30W)
PCIe x1 (#4)
2x USB3.2 Gen1
Header
2x USB3.2 Gen1(#3,#4)
2x USB2.0(P3, P4)
Line in
Line out
Mic in
Connector/Header
Realtek
ALC897
HDA
M.2 Key M
SPI
BIOS

8
Chapter 2 Installation
is is a ATX (12-in x 9.6-in x 1.4-in, 30.5 cm x 24.4 cm x 3.6 cm) form factor moth-
erboard. Before you install the motherboard, study the conguration of your chassis
to ensure that the motherboard ts into it.
2.1 Screw Holes
Place screws into the holes to secure the motherboard to the chassis.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components or
change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static electricity, NEV-
ER place your motherboard directly on the carpet or the like. Also remember to
use a grounded wrist strap or touch a safety grounded object before you handle
components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or
in the bag that comes with the component.
5. Heatsink (e thermal solution of whole system needs to be designed addition-
ally.)
Make sure to unplug the power cord before installing or removing the motherboard. Failure to
do so may cause physical injuries to you and damages to motherboard components.
Do not over-tighten the screws! Doing so may damage the motherboard.
Before you install or remove any component, ensure that the power is switched o or the
power cord is detached from the power supply. Failure to do so may cause severe damage to
the motherboard, peripherals, and/or components.

9
IMB-1713
2.3 Installation of Memory Modules
IMB-1713 provides two 288-pin DDR5 (Double Data Rate 5) Long-DIMM slots, and
supports Dual Channel Memory Technology.
e DIMM only ts in one correct orientation. It will cause permanent damage to the moth-
erboard and the DIMM if you force the DIMM into the slot in the incorrect orientation.
1. For dual channel conguration, you always need to install identical (the same brand,
speed, size and chip-type) DDR5 DIMM pairs.
2. It is unable to activate Dual Channel Memory Technology with only one memory
module installed.
3. It is not allowed to install a DDR, DDR2, DDR3 or DDR4 memory module into a
DDR5 slot; otherwise, this motherboard and DIMM may be damaged.

10
1
2
3
Open the DIMM slot latches.
Aligh the notch. Carefully press down until the
DIMM slides into the slot.
e latches snap back into place.

11
IMB-1713
1
2
3
2.4 Expansion Slots
ere are 3 PCI Express slots, 4 PCI slots and 1 M.2 socket on this motherboard.
PCIE slots: PCIE1 (PCIE 5.0 x16 slot) is used for PCI Express x16 lane width cards.
PCIE2 (PCIE 3.0 x4 slot) is used for PCI Express x 4 lane width cards.
PCIE3 (PCIE 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCI slots: e PCI1, PCI2, PCI3 and PCI4 slots are used to install expansion cards
that have 32-bit PCI interface.
M.2 sockets: 1 x M.2 (Key M, 3042/2260/2280/22110) with PCIe Gen3 x 1
21
57
58
67
68
75
74
M.2_M1
Pin Signal Name SiSignal Name Pin
2 +3.3V GND 1
4 +3.3V GND 3
6NA NA 5
8NA NA 7
10 LED GND 9
12 +3.3V NA 11
14 +3.3V NA 13
16 +3.3V GND 15
18 +3.3V NA 17
20 NA NA 19
22 NA GND 21
24 NA NA 23
26 NA NA 25
28 NA GND 27
30 NA NA 29
32 NA NA 31
34 NA GND 33
36 NA NA 35
38 NA NA 37
40 SMB_CLK GND 39
42 SMB_DATA PERn0 41
44 NA PERp0 43
46 NA GND 45
48 NA PETn0 47
50 PERST# PETP0 49
52 CLKREQ# GND 51
54 NA PEFCLKn 53
56 NA PEFCLKp 55
58 NA GND 57
Mechanical Key
68 NA NA 67
70 +3.3V PEDET 69
72 +3.3V GND 71
74 +3.3V GND 73
GND 75
Slot Power Consumption
(Maximum)
PCIE1 75W
PCIE2 25W
PCIE3 25W
PCI1 25W
PCI2 25W
PCI3 25W
PCI4 25W

12
2.5 Jumpers Setup
The illustration shows how jumpers are setup.
When the jumper cap is placed on pins, the
jumper is “Short.” If no jumper cap is placed
on pins, the jumper is “Open.” The illustration
shows a 3-pin jumper whose pin1 and pin2 are
“Short” when jumper cap is placed on these 2
pins.
Jumper Setting Description
PWR LOSS Jumper
(2-pin PWR_LOSS1)
(see p. 4, No. 7)
is header provides ATX power supply ATX+5VSB dummy load for quick power loss.
Clear CMOS Jumpers
(3-pin CLRMOS1)
(see p. 4, No. 13)
NOTE: CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power cord
from the power supply. Aer waiting for 15 seconds, use a jumper cap to short pin2
and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right
aer you update the BIOS. If you need to clear the CMOS when you just nish updat-
ing the BIOS, you must boot up the system rst, and then shut it down before you do
the clear-CMOS action. Please be noted that the date, time, user default prole will be
cleared only if the CMOS battery is removed.
(2-pin CLRMOS2)
(see p. 4, No. 13)
NOTE: CLRMOS2 allows you to clear the data in CMOS automatically when AC pow-
er on. e data in CMOS includes system setup information such as system password
and system setup parameters. To clear and reset the system parameters to default setup,
please turn o the computer and unplug the power cord, and then use a jumper cap to
short the pins on CLRMOS2.
Clear CMOSDefault
CLRMOS1
Setting Description
Open No Power Loss
Short Power Loss
Setting Description
1-2 Normal (Default)
2-3 Clear CMOS
CLRMOS2
Setting Description
Open Normal (Default)
Short Auto Clear CMOS
(Power On)
2
1
1
2

13
IMB-1713
Digital Input / Output Power Select (JGPIOPWR)
(5-pin JGPIO_PWR1)
(see p. 4, No. 20)
If you want to use the printer port function, please short pin4 and pin5 on Digital
Input / Output Power Select (JGPIO_PWR1). e header can used to provide voltage
settings, GND, 5V or 12V, for pin 10 and pin 12 of Jumper LPT_GPIO1. e maximun
current JGPIOPWR provides is 1A.
COM Port Pin9 PWR Setting Jumpers
(3-pin PWR_COM1~6 (For COM Port1~6))
(see p. 4,No. 17, 29)
e maximum current per port is 1A. e power supply of pin 9 of COM ports is either
5V or 12V, controlled by COM port pin 9 power setting jumpers.
ATX/AT Mode Jumper
(2-pin SIO_AT1)
(see p. 4, No. 15)
e header provides auto boot function when AC power on. If you need the function,
short SIO_AT1 pin 1 and pin 2.
Chassis Intrusion Jumpers (CI1, CI2)
(2-pin CI1, CI2)
(see p. 4, No. 16)
is motherboard supports CASE OPEN detection feature that detects if the chassis
cover has been removed. is feature requires a chassis with chassis intrusion detection
design.
1
Setting Description
Open
ATX Mode
(Default)
Short AT Mode
C I2
Setting Description
Open Active Case Open
Short Normal
C I1
Setting Description
Open Normal
Short Active Case Open
Setting Description
1-2 +5V (Default)
2-3 +12V
Setting Description
1-2 +12V
2-3 +5V
3-4 +5V
4-5 GND (Default)
1 5
2
1
2
1

14
Digital Input / Output Default Value Setting
(3-pin JGPIO_SET1)
(see p. 4, No. 21)
e header is used for GPIO default value setting for either pull high or pull low.
Pulling the header to a high/low value means the voltage is anchored to VCC/GND,
in a stable, non-oating state.
DACC1
(2-pin DACC1)
(see p. 4, No. 27)
Auto clear CMOS when system boot improperly.
Setting Description
1-2 Pull-High
(Default)
2-3 Pull-Low
21 Setting Description
Open
Disabled Auto Clear
CMOS
Short
Enabled Auto Clear
CMOS (Default)

15
IMB-1713
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these
headers and connectors. Placing jumper caps over the headers and connectors will cause per-
manent damage to the motherboard!
Chassis FAN Connectors (+12V)
(4-pin CHA_FAN1)
(see p. 4, No. 1)
(4-pin CHA_FAN3)
(see p. 4, No. 3)
(4-pin CHA_FAN2)
(see p. 4, No. 9)
e board oers three 4-pin chassis fan (Smart Fan) connectors which are compatible with
3-pin chassis fan. If you connect a 3-pin chassis fan to the chassis fan connector on this moth-
erboard, please connect it to pin 1-3. e maximum current is 1A.
8-pin ATX 12V Power Connector
(8-pin ATX12V1)
(see p. 4, No. 2)
is motherboard provides an 8-pin ATX 12V power connector. To use a 4-pin ATX
power supply, please plug it along Pin 1 and Pin 5.
4
1
8
5
4 1
1 4
1
4
Pin Signal Name
1GND
2+12V
3CHA_FAN_SPEED
4FAN_SPEED_CONTROL
Pin Signal Name
1GND
2GND
3GND
4GND
5ATX12V
6ATX12V
7ATX12V
8ATX12V