ASROCK QC7000M User manual

Version 1.0
Published November 2019
Copyright©2019 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com

AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: [phone] ext.123 (Standard International call charges apply)
e terms HDMI® and HDMI High-Denition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.

1
English
QC7000M / QC6000M
Motherboard Layout
RoHS
BIOS
ATXPWR1
FSB800
DDR3_A1 (64 bit, 240-pin module)
DDR3_A2 (64 bit, 240-pin module)
LAN
1
CLRCMOS1
PCIE2
1
USB6_7
1
USB4_5
HD_AUDIO1
1
CHA_FAN1
SPEAKER1
1
HDLED RESET
PLED PWRBTN
1
PANEL1
RJ-45 LAN
USB 2.0
T: USB2
B: USB3
CPU_FAN1
21
3
4
7
USB 2.0
T: USB0
B: USB1
PS2
Keyboard/
Mouse
HDMI1
Top:
LINE I N
Center:
FRONT
Bottom:
MIC IN
8
CHA_FAN2
USB 3.2 Gen1
T: USB0
B: USB1
AUDIO
CODEC
COM1 VGA1
CMOS
Battery
PCIE3
PCIE1
12
11
10 9
13
SATA3_1
SATA3_2
5
6

English
2
No. Description
1 CPU Fan Connector (CPU_FAN1)
2 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_A2)
3 Chassis Fan Connector (CHA_FAN1)
4 ATX Power Connector (ATXPWR1)
5 SATA3 Connector (SATA3_1)
6 SATA3 Connector (SATA3_2)
7 USB 2.0 Header (USB4_5)
8 Chassis Fan Connector (CHA_FAN2)
9 System Panel Header (PANEL1)
10 Chassis Speaker Header (SPEAKER1)
11 Clear CMOS Jumper (CLRCMOS1)
12 USB 2.0 Header (USB6_7)
13 Front Panel Audio Header (HD_AUDIO1)

3
English
QC7000M / QC6000M
I/O Panel
No. Description No. Description
1 USB 2.0 Ports (USB01) 7 USB 3.2 Gen1 Ports (USB3_0_1)
2 LAN RJ-45 Port* 8 HDMI Port
3 Line In (Light Blue) 9 D-Sub Port
4 Front Speaker (Lime) 10 COM Port
5Microphone (Pink) 11 PS/2 Mouse/Keyboard Port
6 USB 2.0 Ports (USB_2_3)
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
1 2
6711 8910
4
5
3

English
4
Chapter 1 Introduction
ank you for purchasing ASRock QC7000M / QC6000M motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
In this manual, Chapter 1 and 2 contains the introduction of the motherboard
and step-by-step installation guides. Chapter 3 contains the operation guide of the
soware and utilities. Chapter 4 contains the conguration guide of the BIOS setup.
1.1 Package Contents
• ASRock QC7000M / QC6000M Motherboard (Micro ATX Form Factor)
• ASRock QC7000M / QC6000M Quick Installation Guide
• ASRock QC7000M / QC6000M Support CD
• 2 x Serial ATA (SATA) Data Cables (Optional)
• 1 x I/O Panel Shield
Because the motherboard specications and the BIOS soware might be updated, the
content of this manual will be subject to change without notice. In case any modica-
tions of this manual occur, the updated version will be available on ASRock’s website
without further notice. If you require technical support related to this motherboard,
please visit our website for specic information about the model you are using. You
may nd the latest VGA cards and CPU support list on ASRock’s website as well.
ASRock website http://www.asrock.com.

5
English
QC7000M / QC6000M
1.2 Specications
Platform • Micro ATX Form Factor
• Solid Capacitor design
• High Density Glass Fabric PCB
CPU • AMD FT3b Carrizo-L E2-7110 Quad-Core APU
(for QC7000M)
• AMD FT3b Beema E2-6110 Quad-Core APU (for QC6000M)
Chipset • SOC
Memory • 2 x DDR3 DIMM Slots
• Supports DDR3 1600/1333 non-ECC, un-buered memory
• Max. capacity of system memory: 32GB
* Please refer to Memory Support List on ASRock's website for
more information. (http://www.asrock.com/)
Expansion
Slot
• 1 x PCI Express 2.0 x16 Slot (PCIE2: x4 mode)
• 2 x PCI Express 2.0 x1 Slot
Graphics • Integrated AMD Radeon™ R2 Graphics
• DirectX 12, Pixel Shader 5.0 (for QC7000M)
• DirectX 11.1, Pixel Shader 5.0 (for QC6000M)
• Dual graphics output: support D-Sub and HDMI ports by
independent display controllers
• Supports HDMI 1.4 with max. resolution up to
3200x1800@60 Hz or 4096x2160@24 Hz
• Supports D-Sub with max. resolution up to 1920x1200@60Hz
• Supports HDCP 1.4 with HDMI 1.4 Port
Audio • 7.1 CH HD Audio (Realtek ALC887 Audio Codec)
• Supports Surge Protection
• ELNA Audio Caps
LAN • PCIE x1 Gigabit LAN 10/100/1000 Mb/s
• Realtek RTL8111H
• Supports Wake-On-LAN
• Supports Lightning/ESD Protection
• Supports Energy Ecient Ethernet 802.3az
• Supports PXE

English
6
Rear Panel
I/O
• 1 x PS/2 Mouse/Keyboard Port
• 1 x Serial Port: COM1
• 1 x D-Sub Port
• 1 x HDMI Port
• 4 x USB 2.0 Ports (Supports ESD Protection)
• 2 x USB 3.2 Gen1 Ports (Supports ESD Protection)
• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
Storage • 2 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and
Hot Plug
Connector • 1 x CPU Fan Connector (3-pin)
• 2 x Chassis Fan Connectors (1 x 4-pin, 1 x 3-pin)
• 1 x 24 pin ATX Power Connector
• 1 x Front Panel Audio Connector
• 2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD
Protection)
BIOS
Feature
• AMI UEFI Legal BIOS with multilingual GUI support
• Supports “Plug and Play”
• ACPI 1.1 compliance wake up events
• SMBIOS 2.3.1 support
• DRAM Voltage multi-adjustment
Hardware
Monitor
• CPU/Chassis temperature sensing
• CPU/Chassis Fan Tachometer
• CPU/Chassis Quiet Fan
• CPU/Chassis Fan multi-speed control
• Voltage monitoring: +12V, +5V, +3.3V, Vcore
OS • Microso® Windows® 10 64-bit
Certica-
tions
• FCC, CE
• ErP/EuP ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com

7
English
QC7000M / QC6000M
is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
• Make sure to unplug the power cord before installing or removing the motherboard.
Failure to do so may cause physical injuries to you and damages to motherboard
components.
• In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not over-
tighten the screws! Doing so may damage the motherboard.
Chapter 2 Installation

English
8
2.1 Installing the System Fan
Please install the motherboard into a case with good airow. Although the CPU
is covered by a pre-installed heatsink which allows advanced heat dissipation,
it is highly recommended to use system fan(s) to increase the cooling eciency.

9
English
QC7000M / QC6000M
2.2 Installing Memory Modules (DIMM)
is motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots.
e DIMM only ts in one correct orientation. It will cause permanent damage to
the motherboard and the DIMM if you force the DIMM into the slot at incorrect
orientation.
It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot; other-
wise, this motherboard and DIMM may be damaged.

English
10
1
2
3

11
English
QC7000M / QC6000M
2.3 Expansion Slots (PCI Express Slots)
ere are 3 PCI Express slots on the motherboard.
PCIe slots:
PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE2 (PCIe 2.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIE3 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
Before installing an expansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Please read the documentation of the
expansion card and make necessary hardware settings for the card before you start
the installation.

English
12
2.4 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper
(CLRCMOS1)
(see p.1, No. 11)
CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn o the computer and unplug the power
cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear
the CMOS right aer you update the BIOS. If you need to clear the CMOS when
you just nish updating the BIOS, you must boot up the system rst, and then shut
it down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default prole will be cleared only if the CMOS battery is
removed.
Clear CMOSDefault

13
English
QC7000M / QC6000M
2.5 Onboard Headers and Connectors
System Panel Header
(9-pin PANEL1)
(see p.1, No. 9)
Connect the power
switch, reset switch and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may congure the way to
turn o your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart
the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. e LED is on when
the system is operating. e LED keeps blinking when the system is in S3 sleep state.
e LED is o when the system is in S4 sleep state or powered o (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. e LED is on when
the hard drive is reading or writing data.
e front panel design may dier by chassis. A front panel module mainly consists of
power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When
connecting your chassis front panel module to this header, make sure the wire assign-
ments and the pin assignments are matched correctly.
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND

English
14
Serial ATA3 Connectors
(SATA3_1:
see p.1, No. 5)
(SATA3_2:
see p.1, No. 6)
ese two SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
USB 2.0 Headers
(9-pin USB4_5)
(see p.1, No. 7)
(9-pin USB6_7)
(see p.1, No. 12)
ere are two headers
on this motherboard.
Each USB 2.0 header can
support two ports.
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.1, No. 13)
is header is for
connecting audio devices
to the front audio panel.
SATA3_1
SATA3_2
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must
support HDA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to con-
nect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET

15
English
QC7000M / QC6000M
Chassis Speaker Header
(4-pin SPEAKER1)
(see p.1, No. 10)
Please connect the chassis
speaker to this header.
Chassis Fan Connectors
(4-pin CHA_FAN1)
(see p.1, No. 3)
(3-pin CHA_FAN2)
(see p.1, No. 8)
Please connect fan cables
to the fan connectors and
match the black wire to
the ground pin.
CPU Fan Connector
(3-pin CPU_FAN1)
(see p.1, No. 1)
Please connect fan cables
to the fan connectors and
match the black wire to
the ground pin.
ATX Power Connector
(24-pin ATXPWR1)
(see p.1, No. 4)
is motherboard pro-
vides a 24-pin ATX power
connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
13.
1
+5V
DUMMY
DUMMY
SPEAKER
GND
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTR
OL
GND
FAN_VOLTAGE
CHA
_
FAN
_
SPEED
GN
D
CPU_FA
N_SPEED
FAN_VOLTAGE
12
1
24
13

16
Deutsch
1 Einleitung
Vielen Dank, dass Sie sich für das QC7000M / QC6000M von ASRock entschieden
haben – ein zuverlässiges Motherboard, das konsequent unter der strengen Quali-
tätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit
robustem Design, das ASRocks Streben nach Qualität und Beständigkeit erfüllt.
1.1 Lieferumfang
• ASRock QC7000M / QC6000M-Motherboard (Mini-ITX-Formfaktor)
• ASRock QC7000M / QC6000M-Schnellinstallationsanleitung
• ASRock QC7000M / QC6000M-Support-CD
• 2 x Serial-ATA- (SATA) Datenkabel (optional)
• 1 x E/A-Blendenabschirmung
Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert werden
können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert werden. Falls
diese Dokumentation irgendwelchen Änderungen unterliegt, wird die aktualisierte Version
ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung gestellt. Sollten Sie techni-
sche Hilfe in Bezug auf dieses Motherboard benötigen, erhalten Sie auf unserer Webseite
spezischen Informationen über das von Ihnen verwendete Modell. Auch nden Sie eine
aktuelle Liste unterstützter VGA-Karten und Prozessoren auf der ASRock-Webseite:
ASRock-Webseite http://www.asrock.com.

17
QC7000M / QC6000M
Deutsch
1.2 Technische Daten
Plattform • Micro-ATX-Formfaktor
• Feststoondensator-Design
• Leiterplatte mit hochdichtem Glasgewebe
Prozessor • AMD FT3b Carrizo-L E2-7110 Quad-Core APU
(für QC7000M)
• AMD FT3b Beema E2-6110 Quad-Core APU (für QC6000M)
Chipsatz • SOC
Speicher • 2 x DDR3-DIMM-Steckplätze
• Unterstützt DDR3 1600/1333 non-ECC, ungepuerter Speicher
• Systemspeicher, max. Kapazität: 32 GB
* Weitere Informationen nden Sie in der
Speicherkompatibilitätsliste auf der ASRock-Webseite.
(http://www.asrock.com/)
Erweiter-
ungssteck-
platz
• 1 x PCI-Express 2.0-x16-Steckplatz (PCIE2: x4-Modus)
• 2 x PCI-Express 2.0-x1-Steckplatz
Grakkarte • Integrierte Grakkarte AMD Radeon™ R2
• DirectX 12, Pixel Shader 5.0 (für QC7000M)
• DirectX 11.1, Pixel Shader 5.0 (für QC6000M)
• Dualer Grakkartenausgang Unterstützt D-Sub- und HDMI-
Ports durch unabhängige Monitor-Controller
• Unterstützt HDMI 1.4 mit max. Auösung bis 3200 x 1800 bei
60 Hz oder 4096 x 2160 bei 24 Hz
• Unterstützt D-Sub mit maximaler Auösung von 1920 x 1200
bei 60 Hz
• Unterstützt HDCP 1.4 mit HDMI 1.4-Port
Audio • 7.1-Kanal-HD-Audio (Realtek ALC887-Audiocodec)
• Unterstützt Überspannungsschutz
• ELNA-Audiokondensatoren
LAN • PCIE-x1-Gigabit-LAN 10/100/1000 Mb/s
• Realtek RTL8111H
• Unterstützt Wake-On-LAN
• Unterstützt Schutz gegen Blitzschlag/elektrostatische Entladung
• Unterstützt energieezientes Ethernet 802.3az
• Unterstützt PXE

18
Deutsch
Rückblende,
E/A
• 1 x PS/2-Maus-/Tastaturanschluss
• 1 x Serieller Port: COM1
• 1 x D-Sub-Port
• 1 x HDMI-Port
• 4 x USB-2.0-Ports (unterstützt Schutz gegen elektrostatische
Entladung)
• 2 x USB-3.2-Gen1-Ports (unterstützt Schutz gegen elektrostatische
Entladung)
• 1 x RJ-45-LAN-Port mit LED (Aktivität/Verbindung-LED und
Geschwindigkeit-LED)
• HD-Audioanschlüsse: Line-in / Vorderer Lautsprecher / Mikrofon
Speicher • 2 x SATA-III-6,0-Gb/s-Anschlüsse, unterstützt NCQ, AHCI und
Hot-Plugging
Anschluss • 1 x CPU-Lüeranschluss (3-polig)
• 2 x Gehäuselüeranschlüsse (1 x 4-polig, 1 x 3-polig)
• 1 x 24-poliger ATX-Netzanschluss
• 1 x Audioanschluss an Frontblende
• 2 x USB 2.0-Stileisten (unterstützt 4 USB 2.0-Ports) (unterstützt
Schutz gegen elektrostatische Entladung)
BIOS-
Funktion
• AMI-UEFI-Legal-BIOS mit Unterstützung mehrsprachiger
grascher Benutzerschnittstellen
• Unterstützt „Plug-and-Play“
• ACPI 1.1-konforme Aufweckereignisse
• SMBIOS 2.3.1-Unterstützung
• DRAM-Spannungsmehrfachanpassung
Hard-
wareüberwa-
chung
• CPU-/Gehäusetemperaturerkennung
• CPU-/Gehäuselüertachometer
• Lautloser CPU-/Gehäuselüer
• CPU-/Gehäuselüer-Mehrfachgeschwindigkeitssteuerung
• Spannungsüberwachung: +12 V, +5 V, +3,3 V, Vcore
Betriebssys-
tem
• Microso® Windows® 10, 64 Bit
Zerti-
zierungen
• FCC, CE
• ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich)
* Detaillierte Produktinformationen nden Sie auf unserer Webseite: http://www.asrock.com