ASROCK SBC-311 User manual

1
SBC-310
SBC-311
User Manual
Version 1.0
Published February 2015
Copyright©2015 ASRock INC. All rights reserved.

2
Version 1.0
Published February 2015
Copyright©2015 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
e terms HDMITM and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com

3
Contents
1 Introduction ....................................................... 5
1.1 Package Contents ......................................................... 5
................................................................. 6
1.3 Motherboard Layout....................................................... 8
1.4 I/O Panel........................................................................ 10
2 Installation ......................................................... 11
2.1 Screw Holes................................................................... 11
2.2 Pre-installation Precautions ........................................... 11
2.3 Installation of Memory Modules (SO-DIMM).................. 12
2.4 Expansion Slots (mini-PCIe and mini-PCIe/mini-SATA
Slots).............................................................................. 13
2.5 Jumpers Setup............................................................... 14
2.6 Onboard Headers and Connectors................................ 16
3 UEFI SETUP UTILITY......................................... 21
3.1 Introduction .................................................................... 21
3.1.1 UEFI Menu Bar .................................................... 21
3.1.2 Navigation Keys ................................................... 22
3.2 Main Screen................................................................... 22
3.3 Advanced Screen........................................................... 24
 ............................................... 25
........................................... 27
 .......................................... 29
3.3.4 Intel(R) Rapid Start Technology ........................... 30
 ............................................... 31
 ........................................ 32
............................................... 33
 ............................................... 34
........................................... 35
3.4 Hardware Health Event Monitoring Screen ................... 36
3.5 Boot Screen ................................................................... 37
3.6 Security Screen ............................................................. 39
3.7 Exit Screen .................................................................... 40

4
4 Software Support .............................................. 41
4.1 Install Operating System................................................ 41
4.2 Support CD Information ................................................. 41
4.2.1 Running Support CD ............................................ 41
4.2.2 Drivers Menu........................................................ 41
4.2.3 Utilities Menu........................................................ 41
4.2.4 Contact Information.............................................. 41

5
Chapter 1: Introduction
Thank you for purchasing ASRock SBC-310 / SBC-311 motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It
delivers excellent performance with robust design conforming to ASRock’s commit-
ment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-

guide to BIOS setup and information of the Support CD.

updated, the content of this manual will be subject to change without no-


the latest VGA cards and CPU support lists on ASRock website as well.
ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit

www.asrock.com/support/index.asp
1.1 Package Contents
ASRock SBC-310 / SBC-311 Motherboard
(3.5” SBC (5.8-in x 4.0-in) / (146 x 102 mm))
ASRock SBC-310 / SBC-311 Driver CD
ASRock SBC-310 / SBC-311 Jumper Setting Instruction

6

Form
Factor Dimensions 3.5” SBC (5.8-in x 4.0-in) / (146 x 102 mm)
Processor
System
CPU
SBC-310:
BGA type for Intel®CoreTM i7-4650/i5-4300U
Haswell ULT Quad/Dual core MCP processor
SBC-311:
BGA type for Intel®CoreTM i3-4010/ Celeron®
2980U Haswell ULT Dual core MCP processor
Core
Number (By CPU, Max 4)
Max Speed (By CPU)
L2 Cache (By CPU)
Chipset (By CPU)
BIOS UEFI
Expansion
Slot
PCI 0
Mini-PCIe 1 (Half Size) + 1 (Full Size ) shared with mSATA
mSATA 1 (Full Size ) shared with SATA2
PCIe 0
CFast Card
Socket 0
Memory
Technology Single Channel DDR3L 1333/1600 MHz SDRAM
Max. 8GB
Socket 1 x SO-DIMM
Graphics
Controller Intel®HD Graphics (By CPU)
VRAM Shared Memory
VGA 0
LVDS 1 co-lay with eDP
HDMI Supports HDMI 1.4a, supported with Level Shift,
resolution up to 4096x2304 (1 x HDMI)
DVI 0
DisplayPort 0
Multi Display Yes (Three Display)
Ethernet
Interface 10/100/1000 Mbps
Controller
GbE LAN1: Realtek RTL8111G, LAN2: Intel®
I218LM (4300U SKU)
GbE LAN1: Realtek RTL8111G, LAN2: Intel®
I218V (2980U SKU)
Connector 2 x RJ-45

7
SATA
Max Data
Transfer
Rate
SATA3 (6.0Gb/s)
Rear I/O
VGA 0
HDMI 2
DVI-I/D 0
DisplayPort 0
Ethernet 2
USB 4 x USB 3.0
Audio 0
Serial 0
e-SATA 0
PS/2 0
Internal
Connector
USB 4 (2 x USB Header 2.54mm pitch)
LVDS/
Inverter 24 bit dual channel LVDS co-lay with eDP
VGA 0
Serial 4 (2 RS-232/422/485, 2 RS-232)
SATA 2 x SATA3 (6.0Gb/s)
m-SATA 1 (shared)
Mini-PCIe 1
Parallel 0
IrDA 0
GPIO 4 x GPI + 4 x GPO
SATA PWR
Output Con 1
Speaker
Header 1
Watchdog
Timer
Output Output from super I/O to drag RESETCON#
Interval 256 Segments, 0,1,2…255 Sec/Min
Power
Requirements
Input PWR DC 9-36 input
Power On
AT/ATX Supported
AT: Directly PWR on as power input ready
ATX: Press button to PWR on after power
input ready
Environment Temperature 0ºC – 60ºC

8
1.3 Motherboard Layout
BIOS
Chip
18
21
23
26
27
29
19
20
22
24
25
28
31
30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
FAN1
1
JGPI O1
mini-PCIe
1
LPC1
SPEA KER1
1
LAN1
HDMI1
PWR_JP1
1
BLT_VOL1
HDLED RESET
PLED PWRBTN
PANEL1
1
mini-PCIe / mini-SATA
CI1
1
SATA_ PW R1
LVDS1
1
1
BLT_PWR1
USB 3.0
T: USB1
B: USB0
COM1 COM2 COM3 COM4
JGP IO_ PW R1
1
CLR MOS 1
1
1
USB8_9
BUZ Z1
1
DDR3 (Support DDR3L Only)
1
BKT_P WR1
1
PNL _P WR1
1
SATA3_1
SATA3_2
BLT_ PW M1
1
USB 3.0
T: USB3
B: USB2
HDMI2
LAN2
CI2
1
MSATA _SE L1
1
1
USB6_7
ATX12V 1
1
PWR _CO M1
1
PWR _CO M2
1
PWR _CO M3
1
PWR _CO M4
1
JGP IO_ SE T1
1
1
HD_AUDIO1

9
1 : Clear CMOS Header
2 : 4-Pin FAN Connector (+12V)
3 : mSATA Select
4 : 2-Pin Buzzer Header
5 : USB2.0 Headers (USB6_7, USB8_9)
6 : Backlight & Amp Volume Control (BLT_VOL1)
7 : Inverter Power Control Wafer (BLT_PWR1)
8 : Backlight Control Level (BLT_PWM1)
9 : Backlight Power Select (LCD_BLT_VCC) (BKT_PWR1)
10 : SATA3 Connectors (SATA3_1, SATA3_2)
11 : Panel Power Selection (LCD_VCC) (PNL_PWR1)
1 2 : SATA Power Output Connector
13 : System Panel Header
14 : ATX/AT Mode Select
15 : ATX Power Connector (Input 9V-36V)
16 : LPC Header
17 : COM Port Header (COM4)
18 : COM Port Pin9 PWR Setting Jumper (PWR_COM4 (For COM Port4))
19 : COM Port Header (COM3)
20 : COM Port Pin9 PWR Setting Jumper (PWR_COM3 (For COM Port3))
21 : COM Port Header (COM2)
22 : COM Port Pin9 PWR Setting Jumper (PWR_COM2 (For COM Port2))
23 : COM Port Header (COM1)
24 : COM Port Pin9 PWR Setting Jumper (PWR_COM1 (For COM Port1))
25 : GPIO Default Setting
26 : Digital Input / Output Power Select
27 : Digital Input / Output Pin Header
28 : 3W Audio AMP Output Wafer
29 : Chassis Intrusion Headers (CI1, CI2)
30 : Front Panel Audio Header
31 : LVDS Panel Connector

10
1.4 I/O Panel
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.
LAN Port LED Indications
Activity/Link LED SPEED LED
Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Off 100Mbps connection
On Link Green 1Gbps connection
1 USB 3.0 Ports (USB01)
2 USB 3.0 Ports (USB23)
3 HDMI Port (HDMI1)
4 HDMI Port (HDMI2)
5 LAN RJ-45 Port (LAN1)*
6 LAN RJ-45 Port (LAN2)*
ACT/LINK
LED
SPEED
LED
LAN Port
6
12 4
35

11
Chapter 2: Installation
This is a 3.5” SBC (5.8-in x 4.0-in) form factor (146 x 102 mm) motherboard. Before
 

Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so may cause physical injuries to you and
damages to motherboard components.
2.1 Screw Holes
Place screws into the holes to secure the motherboard to the chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static electricity,
NEVER place your motherboard directly on the carpet or the like. Also
remember to use a grounded wrist strap or touch a safety grounded object
before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or
in the bag that comes with the component.
Before you install or remove any component, ensure that the power is
switched off or the power cord is detached from the power supply.
Failure to do so may cause severe damage to the motherboard, peripherals,
and/or components.

12
2.3 Installation of Memory Modules (SO-DIMM)
SBC-310 / SBC-311 provides one 204-pin DDR3 (Double Data Rate 3) SO-DIMM
slot, which supports single channel DDR3L SDRAM only.
Step 1. Align a SO-DIMM on the slot such that the notch on the SO-DIMM
matches the break on the slot.
  
the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at
incorrect orientation.
Step 2. Firmly insert the SO-DIMM into the slot until the retaining clips at both
ends fully snap back in place and the SO-DIMM is properly seated.

13
2.4 Expansion Slots (mini-PCIe and mini-PCIe/mini-SATA
Slots)
There is 1 mini-PCIe slot and 1 mini-PCIe/mini-SATA slot on this motherboard.
mini-PCIe slot:
MINI_PCIE1 (mini-PCIe slot; half size) is used for PCI Express mini
cards.
mini-PCIe/mini-SATA slot:
MINI_PCIE2 (mini-PCIe/mini-SATA slot; full size) is used for PCI Ex-
press mini cards or mSATA cards.
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed
in a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
 
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

14
2.5 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.
Clear CMOS Jumper
(CLRCMOS1)
(see p.8, No. 1)
Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the
system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need



address will be cleared only if the CMOS battery is removed.
Clear CMOSDefault
Panel Power Select (LCD_VCC) Use this to set up the VDD
(5-pin PNL_PWR1) power of the LVDS connector.
(see p.8 No. 11) 1-2: +3V
2-3: +5V
3-4: +5V
4-5: +12V
Digital Input/Output Power Select 1-2: +12V
(3-pin JGPIO_PWR1) 2-3: +5V
(see p.8 No. 26)
ATX/AT Mode Select 1-2: AT Mode
(3-pin PWR_JP1) 2-3: ATX Mode
(see p.8 No. 14)
1

15
Backlight Power Select Use this to set up the backlight
(LCD_BLT_VCC) power of the LVDS connector.
(5-pin BKT_PWR1) 1-2: +5V
(see p.8 No. 9) 2-3: +12V
3-4: +12V
4-5: DC_IN Power
COM1 Pin9 PWR Setting Jumpers 1-2: +5V
(3-pin PWR_COM1) 2-3: +12V
(see p.8 No. 24)
(3-pin PWR_COM2)
(see p.8 No. 22)
(3-pin PWR_COM3)
(see p.8 No. 20)
(3-pin PWR_COM4)
(see p.8 No. 18)
Backlight Control Level 1-2: +3V
(3-pin BLT_PWM1) 2-3: +5V
(see p.8 No. 8)
1
mSATA Select 1-2: mini-PCIe
(3-pin MSATA_SEL1) 2-3: mSATA
(see p.8 No. 3)
GPIO Default Setting 1-2: Pull-High
(3-pin JGPIO_SET1) 2-3: Pull-Low
(see p.8 No. 25)

16
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
SATA3 Connectors These two Serial ATA3
(SATA3_1, SATA3_2: see p.8, No. 10) (SATA3) connectors support
SATA data cables for internal
storage devices. The current
SATA3 interface allows up to
6.0 Gb/s data transfer rate.
USB 2.0 Headers There are two USB 2.0
(see p.8 No. 5) headers on this motherboard.
(9-pin USB6_7, USB8_9)
System Panel Header This header accommodates
(9-pin PANEL1) several system front panel
(see p.8 No. 13) functions.
Connect the power switch, reset switch and system status indicator on the
chassis to this header according to the pin assignments below. Note the
positive and negative pins before connecting the cables.
PWRBTN (Power Switch):
 
the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to perform a
normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED
is on when the system is operating. The LED keeps blinking when the sys-
tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep
state or powered off (S5).
DUMMY
GND GND
+B
-B
+A
-A
USB_PWR USB_PWR
1
GND RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
SATA3_2
SATA3_1

17
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED
is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly
consists of power switch, reset switch, power LED, hard drive activity LED,
speaker and etc. When connecting your chassis front panel module to this
header, make sure the wire assignments and the pin assign-ments are
matched correctly.
3W Audio AMP Output Wafer
(4-pin SPEAKER1)
(see p.8 No. 28)
1
PIN Signal Name
1 SPK L-
2 SPK L+
3 SPK R+
4 SPK R-
Fan Connector Please connect the fan cable
(4-pin FAN1) to the fan connector and
(see p.8 No. 2) match the black wire to the
ground pin.
ATX Power Connector (Input 9V-36V) Please connect a DC power
(4-pin ATX12V1) supply (9V-36V) to this
(see p.8 No. 15) connector.
1-4 : GND
2-3 : DC Input
1
FAN_SPEED
FAN_SPEED_CONTROL
+12V
GND 1
2
3
4
SATA Power Output Connector
(4-pin SATA_PWR1)
(see p.8 No. 12)
+5V +12V
1
GND GND
Inverter Power Control Wafer
(6-pin BLT_PWR1)
(see p.8 No. 7)
PIN Signal Name
1 GND
2 GND
3 CON_LBKLT_CTL
4 CON_LBKLT_EN
5 LCD_BLT_VCC
6 LCD_BLT_VCC
1

18
COM Port Headers
(10-pin COM1)
(see p.8 No. 23)
(10-pin COM2)
(see p.8 No. 21)
(10-pin COM3)
(see p.8 No. 19)
(10-pin COM4)
(see p.8 No. 17)
1
2
PIN Signal
Name PIN Signal Name PIN Signal Name PIN Signal Name PIN Signal Name
10 DUMMY 8CCTS# 6DDSR# 4DDTR# 2RRXD
9DUMMY 7RRTS# 5GND 3TTXD 1DDCD#
PIN RS232 RS422 RS485
1 DCD TX- RTX-
2 RXD RX+ N/A
3 TXD TX+ RTX+
4 DTR RX- N/A
5 GND GND GND
6 DSR N/A N/A
7 RTS N/A N/A
8 CTS N/A N/A
9 NA/+5V/+12V N/A N/A
This motherboard supports RS232/422/485 on COM1/COM2 port. Please refer to
  
  
may refer to page 31 for details.

Buzzer Header
(2-pin BUZZ1)
(see p.8 No. 4)
1
+5V
SPKR
Chassis Intrusion Headers This motherboard supports
(2-pin CI1, CI2) CASE OPEN detection feature
(see p.8 No. 29) that detects if the chassis cover
has been removed. This feature
requires a chassis with chassis
intrusion detection design.

19
LVDS Connector
(40-pin LVDS1)
(see p.8 No. 31)
Backlight & Amp Volume Control
(7-pin BLT_VOL1)
(see p.8 No. 6)
PIN Signal Name
1 GPIO_VOL_UP
2 GPIO_VOL_DW
3 PWRDN
4 GPIO_BLT_UP
5 GPIO_BLT_DW
6 GND
7 GND
1
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.8 No. 30)
Digital Input/Output Pin Header
(10-pin JGPIO1)
(see p.8 No. 27)
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
PIN Signal Name PIN Signal Name
2 LCD_VCC 1 LCD_VCC
4 LDDC_CLK 3 +3.3V
6 LVDS_A_DATA0# 5 LDDC_DATA
8 GND 7 LVDS_A_DATA0
10 LVDS_A_DATA1 9 LVDS_A_DATA1#
12 LVDS_A_DATA2# 11 GND
14 GND 13 LVDS_A_DATA2
16 LVDS_A_DATA3 15 LVDS_A_DATA3#
18 LVDS_A_CLK# 17 GND
20 GND 19 LVDS_A_CLK
22 LVDS_B_DATA0 21 LVDS_B_DATA0#
24 LVDS_B_DATA1# 23 GND
26 GND 25 LVDS_B_DATA1
28 LVDS_B_DATA2 27 LVDS_B_DATA2#
30 LVDS_B_DATA3# 29 DPLVDD_EN
32 GND 31 LVDS_B_DATA3
34 LVDS_B_CLK 33 LVDS_B_CLK#
36 CON_LBKLT_EN 35 GND
38 LCD_BLT_VCC 37 CON_LBKLT_CTL
40 LCD_BLT_VCC 39 LCD_BLT_VCC
1
39
40
2
PIN Signal Name PIN Signal Name
1 SIO_GP34 2 SIO_GP30
3 SIO_GP35 4 SIO_GP31
5 SIO_GP36 6 SIO_GP32
7 SIO_GP37 8 SIO_GP33
9 JGPIO_PWR 10 GND

20
LPC Header This connector supports
(19-pin LPC1) Trusted Platform Module (TPM)
(see p.8 No. 16) system, which can securely
 
passwords, and data. A TPM
system also helps enhance
network security, protects
digital identities, and ensures
platform integrity.
1
GND
GND
S_PWRDWN#
LAD2
SMB_CLK_MAIN
PCICLK
PCIRST#
LAD3
+3V
LAD0
GND
FRAME
SMB_DATA_MAIN
LAD1
SERIRQ#
GND +3VSB
48MHz +5V