Asus B250M-C PRO User manual

Motherboard
B250M-C PRO
B250M-C PRO/
CSM

ii
E13586
Revised Edition
October 2017
Copyright © 2017 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”),
under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the
applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data,
you may obtain it for a period of three years after our last shipment of the product, either
(1) for free by downloading it from http://support.asus.com/download
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source
code we would be much obliged if you give us a notication to the email address [email protected], stating
the product and describing the problem (please DO NOT send large attachments such as source code
archives, etc. to this email address).

iii
Contents
Safety information ...................................................................................... iv
About this guide ......................................................................................... iv
Package contents ....................................................................................... vi
B250M-C PRO specications summary.................................................... vi
Chapter 1 : Product introduction
Motherboard overview ............................................................................. 1-1
Central Processing Unit (CPU)................................................................ 1-7
System memory........................................................................................ 1-8
Chapter 2 : BIOS information
BIOS setup program................................................................................. 2-1
BIOS menu screen.................................................................................... 2-2
Exit menu................................................................................................... 2-3
Appendix
Notices.......................................................................................................A-1
ASUS contact information .......................................................................A-5

iv
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
• When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
• Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
• Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
• Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your retailer.
Operation safety
• Before installing the motherboard and adding components, carefully read all the manuals
that came with the package.
• Before using the product, ensure all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may be exposed to moisture.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualied service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and conguring the
motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it
supports. It includes descriptions of the switches, jumpers, and connectors on the
motherboard.
• Chapter 2: BIOS information
This chapter discusses changing system settings through the BIOS Setup menus.
Detailed descriptions for the BIOS parameters are also provided.

v
Where to nd more information
Refer to the following sources for additional information and for product and software
updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as warranty yers,
that may have been added by your dealer. These documents are not part of the
standard package.
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when
completing a task.
CAUTION: Information to prevent damage to the components when
completing a task
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text Indicates a menu or an item to select.
Italics Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).

vi
B250M-C PRO specications summary
(continued on the next page)
Package contents
Check your motherboard package for the following items.
Motherboard ASUS B250M-C PRO motherboard
Cables 2 x Serial ATA 6.0 Gb/s cables
Accessories 1 x ASUS I/O Shield
1 x M.2 Screw package
Application DVD Support DVD
Documentation User Guide
If any of the above items is damaged or missing, contact your retailer.
CPU
LGA1151 socket for Intel®7th/6th Generation Core™ i7 / i5 / i3, Pentium®, and
Celeron®processors
Supports Intel®14nm CPU
Supports Intel®Turbo Boost Technology 2.0*
* The Intel®Turbo Boost Technology 2.0 support depends on the CPU types.
** Refer to www.asus.com for Intel®CPU support list.
Chipset Intel®B250 Chipset
Memory
4 x DIMMs, max. 64GB, DDR4 2133/2400 MHz, non-ECC, un-buffered memory
Dual-channel memory architecture
Supports Intel® Extreme Memory Prole (XMP)
* Hyper DIMM support is subject to the physical characteristics of individual CPUs. Please
refer to Memory QVL for details
** Refer to www.asus.com for the Memory QVL (Qualied Vendors List).
Expansion
slots
1 x PCI Express 3.0/2.0 x16 slot
1 x PCI Express 3.0/2.0 x16 slot (at x4 mode)
1 x PCI Express 3.0/2.0 x1 slot
1 x PCI slot
Graphics
Integrated graphics processor - Intel®HD Graphics support
Multi-VGA output support :Dual DP / DVI-I ports
- Supports DisplayPort with maximum resolution 4096x2304@60Hz
- Supports DVI-I with maximum resolution 1920x1200@60Hz
Supports Intel®InTruTM 3D, Quick Sync Video, Intel®Clear Video HD Technology, and
Intel® InsiderTM
Maximum shared memory of 1024 MB
Storage
Intel®B250 Chipset:
- 6 x SATA 6.0 Gb/s ports (gray)
- 1 x M.2 Socket with M Key, type 2242/2260/2280/22110 storage devices @ PCIe
x 4 mode
- Ready for Intel®Optane Memory*
* Intel®Optane Technology is only supported when using 7th Generation Intel®Processors.
Before using Intel®Optane memory modules, ensure that you have updated your
motherboard drivers and BIOS to the latest version from ASUS support website.

vii
B250M-C PRO specications summary
(continued on the next page)
Audio Realtek® ALC887 8-channel High Denition Audio CODEC
- Supports jack-detection and front panel jack-retasking
Multi-GPU
support Cross Fire X
LAN Intel®I219V Gigabit LAN Controller
USB
Intel®B250 Chipset:
- 6 x USB 3.0/2.0 ports (2 ports at mid-board; 4 ports at back panel)
- 6 x USB 2.0/1.1 ports (4 ports at mid-board; 2 ports at back panel)
ASUS
special
features
Dependable stability:
ASUS 5X PROTECTION III:
- ASUS LANGuard - Surge-protected networking
- ASUS Overvoltage Protection - World-class circuit-protecting power design
- ASUS Stainless Steel Back I/O - 3X more durable
- ASUS SafeSlot Core- Fortied PCIe with Solid Soldering
- ESD Guards - Electrostatic discharge protection
Durability
Anti-moisture coating
- Outstanding protection against moisture and corrosion
UEFI BIOS:
- Most advanced options with fast response time
Easy PC DIY:
Safe motherboard mounting
- Component-free areas to minimize damage risk
Q-Design
- ASUS Q-DIMM
- ASUS Q-Slot
Rear panel
I/O ports
1 x PS/2 keyboard port
1 x PS/2 mouse port
2 x DisplayPorts
1 x DVI-I port
1 x LAN (RJ-45) port
2 x USB 2.0/1.1 ports
4 x USB 3.0/2.0 ports
3 x Audio jacks support 8-channel audio output*
* Use a chassis with HD audio module in the front panel to support an 8-channel audio
output.
Internal
connectors
1 x USB 3.0/2.0 connector supports additional 2 USB 3.0/2.0 ports
2 x USB 2.0/1.1 connectors support additional 4 USB 2.0/1.1 ports
6 x SATA 6.0Gb/s connectors
1 x 4-pin CPU Fan connector
2 x Chassis Fan connectors
1 x Front panel audio connector
1 x System panel connector

viii
B250M-C PRO specications summary
Specications are subject to change without notice.
Internal
connectors
1 x 24-pin EATX Power connector
1 x 4-pin ATX 12V Power connector
1 x Speaker connector
2 x COM headers
1 x LPT header
1 x Chassis Intrusion header
1 x Clear CMOS header
1 x MONO-out header(with AMP IC)
1 x 14-1 pin TPM header
BIOS features
64 Mb Flash ROM, UEFI AMI BIOS, PnP, DMI3.0, WfM2.0, SM BIOS 3.0, ACPI
5.1, Multi-language BIOS, ASUSbackup, LOGO ash, ME update, DMI value edit,
BIOS value edit
Manageability WfM 2.0, DMI 3.0, WOL, WOR, PXE
Support DVD Drivers
OS support
Windows®10 (64-bit)
Windows®8.1 (64-bit)*
Windows®7 (64-bit/32-bit)*
* Windows®8.1 (64-bit) and Windows®7 (32/64-bit) are only supported when using 6th
Generation Intel®Processors.
Form factor mATX form factor: 9.6 in. x 9.1 in. (24.4 cm x 23.1 cm)

ASUS B250M-C PRO 1-1
Product introduction
1
Motherboard overview
• Unplug the power cord from the wall socket before touching any component.
• Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due
to static electricity.
• Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so
may cause severe damage to the motherboard, peripherals, or components.
• Unplug the power cord before installing or removing the motherboard. Failure to do so
can cause you physical injury and damage to motherboard components.
Place this
side towards
the rear of the
chassis
B250M-C PRO
PCI
PCIEX1
SPEAKER
CHASSIS
CLRTC
F_PANEL
TPM
LPT
USB3_12
AAFP
MONO_OUT
ATX12V
EATXPWR
CPU_FAN
CHA_FAN1
CHA_FAN2
BATTERY
PCIEX16_1
PCIEX16_2
Super
I/O
ASM
1083
ALC
887
WG
I219V
RTD
2168
DIGI
+VRM
24.4cm(9.6in)
23.1cm(9.1in)
LGA1151
Intel®
B250
DDR4 DIMM_A1 (64bit, 288-pin module)
228022110 2260 2242
M.2(SOCKET3)
PCIE SATA IRST
X4 VX
DDR4 DIMM_A2 (64bit,288-pin module) DDR4 DIMM_B1 (64bit, 288-pin module) DDR4 DIMM_B2 (64bit, 288-pin module)
AUDIO
KBMS
DP12
LAN_USB78
USB3_34
USB3_56
64Mb
BIOS
SATA6G_4 SATA6G_3
SATA6G_6 SATA6G_5
SATA6G_2 SATA6G_1
USB1112USB910
COM1 COM2
DVI
1 432 51
1
10112 11 9
2
7
8
14
18
6
6
6131516
19
17
17
20
Scan the QR code to get the detailed pin denitions.

1-2 Chapter 1: Product introduction
CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1/2)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufcient air ow inside
the system may damage the motherboard components. These are not jumpers! Do not
place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan
of maximum 1A (12 W) fan power.
ATX power connectors (24-pin EATXPWR, 8-pin ATX12V)
Correctly orient the ATX power supply plugs into these connectors and push down
rmly until the connectors completely t.
• For a fully congured system, we recommend that you use a power supply unit
(PSU) that complies with ATX 12 V Specication 2.0 (or later version) and provides
a minimum power of 350 W.
• If you are uncertain about the minimum power supply requirement for your system,
refer to the Recommended Power Supply Wattage Calculator at http://support.
asus.com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for
details.
M.2 socket 3
These sockets allow you to install an M.2 (NGFF) SSD module.
These sockets support M Key and 2242/2260/2280 storage
devices.
Intel®LGA1151 CPU socket
Install Intel®LGA1151 CPU into this surface mount LGA1151 socket, which is
designed for 7th / 6th Generation Intel®Core™ i7 / i5 / i3, Pentium®, and Celeron®
processors.
For more details, refer to Central Processing Unit (CPU).
DDR4 DIMM slots
This motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory
Module (DIMM) sockets. A DDR4 module is notched differently from a DDR, DDR2,
or DDR3 module.
For more details, refer to System memory.
DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
M.2(SOCKET3)

ASUS B250M-C PRO 1-3
Intel®B250 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~6)
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0
Gb/s signal cables.
When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to
[AHCI].
USB 3.0 connector (20-1 pin USB3_12)
Connect a USB 3.0 module to this connector for additional USB 3.0 front or rear
panel ports. This connector complies with USB 3.0 specications and provides faster
data transfer speeds of up to 5 Gbps, faster charging time for USB-chargeable
devices, optimized power efciency, and backward compatibility with USB 2.0.
TPM connector (14-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which can
securely store keys, digital certicates, passwords and data. A TPM system also
helps enhance network security, protects digital identities, and ensures platform
integrity.
Speaker connector (4-pin SPEAKER)
The 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system warnings.
System panel connector (10-1 pin F_PANEL)
This connector supports several chassis-mounted functions.
Clear RTC RAM (2-pin CLRTC)
This header allows you to uncongure ME and clear the CMOS
RTC RAM data of the system setup information such as date, time,
and system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Use a metal object such as a screwdriver to short the two
pins.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter
BIOS setup to re-enter data.
If the steps above do not help, remove the onboard battery and short the two pins again
to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
CLRTC
+3V_BAT GND
PIN 1

1-4 Chapter 1: Product introduction
Chassis intrusion header (4-1 pin CHASSIS)
This header is for a chassis-mounted intrusion detection sensor or switch. Connect
one end of the chassis intrusion sensor or switch cable to this connector. The
chassis intrusion sensor or switch sends a high-level signal to this connector when
a chassis component is removed or replaced. The signal is then generated as a
chassis intrusion event.
By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper
cap. Remove the jumper caps only when you intend to use the chassis intrusion
detection feature.
USB 2.0 connectors (10-1 pin USB78,USB910)
Connect the USB module cable to any of these connectors, then install the module
to a slot opening at the back of the system chassis. These USB connectors comply
with USB 2.0 specications and support up to 480Mbps connection speed.
LPT connector (26-1 pin LPT)
The LPT (Line Printing Terminal) connector supports devices such as a printer.
LPT standardizes as IEEE 1284, which is the parallel port interface on IBM PC-
compatible computers.
Serial port connectors (10-1 pin COM)
Connect the serial port module cable to these connectors, then install the module
to a slot opening at the back of the system chassis.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports
HD Audio standard. Connect one end of the front panel audio I/O module cable to
this connector.
We recommend that you connect a high-denition front panel audio module to this
connector to avail of the motherboard’s high-denition audio capability.
PCI Express 3.0/2.0 x16 slots
This motherboard has two PCI Express 3.0/2.0 x16 slots that support PCI Express
3.0/2.0 x16 graphic cards complying with the PCI Express specications.
PCI slot
The PCI slot supports cards such as a LAN card, SCSI card, USB card, and other
cards that comply with PCI specications.
Mono out header (2-pin MONO_OUT)
This internal mono out header allows connection to an internal, low power speaker
for basic system sound capability. The subsystem is capable of driving a speaker
load of 2 Ohms at 2 Watts (rms).
PCI Express 3.0/2.0 x1 slot
This motherboard has one PCI Express 3.0/2.0 x1 slot that supports PCI Express
network cards, SCSI cards, and other cards that comply with the PCI Express
specications.

ASUS B250M-C PRO 1-5
1. PS/2 mouse port (green). This port is for a PS/2 mouse.
2. DVI-I port. This port is for any DVI-I compatible device.
3. DisplayPorts. These ports are for a DisplayPort-compatible device.
4. LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub.
LAN port LED indications
Rear panel connectors
1 43
810
5 6
7
2
9 8
5. Line In port (light blue). This port connects to the tape, CD, DVD player, or other
audio sources.
6. Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, 5.1
and 7.1-channel congurations, the function of this port becomes Front Speaker Out.
Activity/Link LED Speed LED
Status Description Status Description
Off No link OFF 10Mbps connection
Orange Linked ORANGE 100Mbps connection
Orange (Blinking) Data activity GREEN 1Gbps connection
Orange (Blinking
then steady)
Ready to wake up
from S5 mode
_ _
7. Microphone port (pink). This port connects to a microphone.
Refer to the audio conguration table for the function of the audio ports in 2.1, 4.1, 5.1, or
7.1-channel conguration.

1-6 Chapter 1: Product introduction
Audio 2.1, 4.1, 5.1, or 7.1-channel conguration
Port Headset
2.1-channel 4.1-channel 5.1-channel 7.1-channel
Light Blue (Rear
panel) Line In Rear Speaker Out Rear Speaker Out Rear Speaker Out
Lime (Rear panel) Line Out Front Speaker Out Front Speaker Out Front Speaker Out
Pink (Rear panel) Mic In Mic In Bass/Center Bass/Center
Lime (Front panel) - - - Side Speaker Out
To congure a 7.1-channel audio output:
Use a chassis with HD audio module in the front panel to support a 7.1-channel audio
output.
8. USB 3.0 ports. These 9-pin Universal Serial Bus (USB) ports are for USB 3.0/2.0
devices.
• USB 3.0 devices can only be used for data storage.
• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster
and better performance from your USB 3.0 devices.
• Due to the design of the Intel®200 series chipset, all USB devices connected to the
USB 2.0 and USB 3.0 ports are controlled by the xHCI controller. Some legacy USB
devices must update their rmware for better compatibility.
9. USB 2.0 ports. These 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1
devices.
10. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.

ASUS B250M-C PRO 1-7
Central Processing Unit (CPU)
This motherboard comes with a surface mount LGA1151 socket
designed for 7th / 6th Generation Intel®Core™ i7 / i5 / i3, Pentium®, and
Celeron®processors.
• Ensure that you install the correct CPU designed for the LGA1151 socket only. DO
NOT install a CPU designed for LGA1150, LGA1155 and LGA1156 sockets on the
LGA1151 socket.
• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and
the socket contacts are not bent. Contact your retailer immediately if the PnP cap
is missing, or if you see any damage to the PnP cap/socket contacts/motherboard
components.
• Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the
LGA1151 socket.
• The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
Installing the CPU
1
4
Unplug all power cables before installing the CPU.
Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the
heatsink and fan if necessary.
2
3
A
B
A
B
C
D
5
4
4
5

1-8 Chapter 1: Product introduction
System memory
Overview
This motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory Module
(DIMM) sockets. A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module.
DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot.
Channel Sockets
Channel A DIMM_A1 & DIMM_A2
Channel B DIMM_B1 & DIMM_B2
DIMM_A1
DIMM_A2
DIMM_B1
DIMM_B2
• You may install varying memory sizes in Channel A and Channel B. The system
maps the total size of the lower-sized channel for the dual-channel conguration. Any
excess memory from the higher-sized channel is then mapped for single-channel
operation.
• Always install the DIMMS with the same CAS Latency. For an optimum compatibility,
we recommend that you install memory modules of the same version or data code
(D/C) from the same vendor. Check with the vendor to get the correct memory
modules.
• According to Intel®CPU spec, DIMM voltage below 1.35V is recommended to protect
the CPU.
• Due to the memory address limitation on 32-bit Windows®OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
- Use a maximum of 3 GB system memory if you are using a 32-bit Windows®OS.
- Install a 64-bit Windows®OS if you want to install 4GB or more on the
motherboard.
- For more details, refer to the Microsoft®support site at http://support.microsoft.
com/kb/929605/en-us.
Visit the ASUS website at www.asus.com for the latest QVL.
Installing a DIMM
1 2
To remove a DIMM
B
A
B
A
A

ASUS B250M-C PRO 1-9
Installing a DIMM
1 2
To remove a DIMM
B
A
B
A
A
Recommended memory conguration

BIOS information
2
Scan the QR code to view the BIOS update guide.
BIOS setup program
Use the BIOS Setup program to update the BIOS or congure its
parameters. The BIOS screens include navigation keys and brief online
help to guide you in using the BIOS Setup program.
Entering BIOS Setup at startup
To enter BIOS Setup at startup:
Press <Delete> or <F2> during the Power-On Self Test (POST). If you do not press <Delete>
or <F2>, POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
• Press <Ctrl>+<Alt>+<Del> simultaneously.
• Press the reset button on the system chassis.
• Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the rst two options.
Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from a
running operating system can cause damage to your data or system. We recommend you
always shut down the system properly from the operating system.
• The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
• Visit the ASUS website at www.asus.com to download the latest BIOS le for this
motherboard.
• If the system becomes unstable after changing any BIOS setting, load the default
settings to ensure system compatibility and stability. Select the Load Optimized
Defaults item under the Exit menu or press hotkey F5.
• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. See section Motherboard overview for
information on how to erase the RTC RAM.
ASUS B250M-C PRO
2-1

BIOS menu screen
:Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.17.1246 Copyright (C) 2016 American Megatrends, Inc.
Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.
Main Ai Tweaker Advanced Monitor Boot Tool Exit
Choose the default
language
BIOS Version 0205 x64
Build Date 03/24/2017
ME Firmware Version 11.6.0.1126
PCH Stepping AO
Processor Information
Brand String Intel(R)Core(TM)CPU
G3900TE @ 2.30GHz
CPU Speed 2300MHz
Total Memory 4096MB
Memory Frequency 2133MHz
System Language [English]
System Date [Fri 01/01/2016]
System Time [00:34:15]
Access Level Administrator
Security
BIOS Information
Menu bar
Menu items
General Help
Conguration elds
Sub-menu item
2-2
Chapter 2: BIOS information

Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a conrmation window appears.
Select OK to load the default values.
Save Changes & Reset
Once you are nished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press <F10>,
a conrmation window appears. Select OK to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press <Esc>, a conrmation window appears. Select OK to discard
changes and exit.
Launch EFI Shell from USB drives
This option allows you to attempt to launch the EFI Shell application (shellx64.e) from one of
the available USB devices.
Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items.
:Select Screen
: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.17.1246 Copyright (C) 2016 American Megatrends, Inc.
Exit system setup without
saving any changes.
Load Optimized Defaults
Save Changes & Reset
Discard Changes & Exit
Launch EFI Shell from USB drives
Aptio Setup Utility - Copyright (C) 2016 American Megatrends, Inc.
Main Ai Tweaker Advanced Monitor Boot Tool Exit
ASUS B250M-C PRO
2-3