AtGames HAA310 User manual

INSTRUCTION MANUAL FOR TRACKBALL (HAA310)
Images and instructions are for reference only and subject to change. © 2022 AtGames. 1
Tools Needed P.1
Package Includes P.1
How to Install Trackball onto ALU P.2
How to Install Trackball onto Quadplay P.5
Trackball Rim Trackball Trackball Case
#SA Screw x 3 #SB Screw x 4
Blue Cable
(for ALU 1.0 version)
Red Cable
(for ALU 1.1 version and Quadplay)
Package includes:
Tools Needed:
A Phillips-head Screwdriver.

Images and instructions are for reference only and subject to change. © 2022 AtGames.
HOW TO INSTALL TRACKBALL ONTO ALU
2
Remove the screws attaching the control panel to
the cabinet. (If you have the Pinball Kit installed,
please remove) Partiallyslide out the control panel
and carefully unplug the rear connecting cables.
Once cables are unplugged, fully remove the
control panel.
Step 1
Flip the control panel upside down and remove all
8 screws on the bottom of the control panel.
Step 2
Carefully hold the trackball ball and rim from
underneath the control panel to avoid damaging
it as you remove the 7 screws indicated.
Step 5
Prepare a new trackball.
Step 6
Carefully remove the control panel's bottom
casing and carefully disconnect the Pinball cables
from the sides.
Important note: The control panel's bottom casing may be
dicult to remove due to a tight t around the housing with
the ports. May need to carefully rock side to side while lifting
to remove. Again, please be careful of the Pinball cables.
Step 3
Remove the cable circled in yellow.
Step 4

3
Images and instructions are for reference only and subject to change. © 2022 AtGames.
HOW TO INSTALL TRACKBALL ONTO ALU
Put the trackball rim back in its original position.
Step 7
While holding the trackball rim in place from
underneath the control panel, placethe new
trackball ball into the control panel using the rim
to hold the ball in place and assemble the
trackball case to its original state.
Step 8
Attach the cable to the trackball from step 4,
circled in yellow.
Step 10
Step 9
Using the 7 screws removed in step 5, fasten them,
circled in yellow, to secure the trackball.
Using the 8 screws removed in step 2, fasten them,
circled in yellow, to secure the control panel case.
Step 12
Carefully attach the Pinball cables from step 3,
circled in yellow,and assemble the control panel
case to its original state.
Step 11

4
Images and instructions are for reference only and subject to change. © 2022 AtGames.
HOW TO INSTALL TRACKBALL ONTO ALU
Reinstallthe control panel remembering to attach
all the connecting cables, and secure with screws
removed in step 1.
Step 13

5
Images and instructions are for reference only and subject to change. © 2022 AtGames.
HOW TO INSTALL TRACKBALL ONTO QUADPLAY
Insert and place the trackball rim from the
underside or feel free toip the control panel over
and insert the trackball rim.
Step 5
If you ipped the control panel over in step 5, ip
it back over while holding the trackball rim in
place. Placethe new trackball ball into the control
panel using the rim to hold the ball in place.
Step 6
Flip the QuadPlay control panel upside down and
remove all 8 covers and screws.
Step 1
Remove the control panel's bottom casing.
Step 2
Using aPhillips-head screwdriver,loosen the 3
screws holding the trackball cover in place and
remove it.
Step 3
Prepare a new trackball.
Step 4

6
Images and instructions are for reference only and subject to change. © 2022 AtGames.
HOW TO INSTALL TRACKBALL ONTO QUADPLAY
Assemble the trackball case and ENSURE the cable
slot on the trackball case, circled in yellow, is
pointing toward the white button.
Step 7
Fasten the included 3 #SA screws, circled in
yellow.
Step 8
Fasten the included 4 #SB screws, circled in blue. Attach the included red/white cable to the CTR board
and trackball case. Does not matter which cable end
goes to which port. Shown with yellow arrows.
Note: The slot on the CTR board is marked “TRACKBALL”.
Step 9
Step 10
Using the 8 screws removed in Step 1,fasten them
to secure the QuadPlay control panel case and
attach the 8 removed covers.
Step 12
Attachthe QuadPlay control panel's bottom
casing removed from Step 2.
Step 11