ATIK Cameras 3 Series User manual

Atik Series 3 User Manual
Version 1.3 – August 2011
Page 1

Table of contents
1 Introduction ................................................................................................................. 3
1.1 Further information .............................................................................................. 3
2 Pack Contents .............................................................................................................. 4
3 Getting to know our camera ...................................................................................... 5
3.1 Camera Parts ......................................................................................................... 5
3.2 Sensor ................................................................................................................... 6
3.3 Optical Window ................................................................................................... 6
3.4 Analog to Digital Converter (ADC) ..................................................................... 6
3.5 Power Consumption ............................................................................................. 6
3.6 USB Port ............................................................................................................... 7
3.7 Autoguiding Port .................................................................................................. 7
3.8 Cooling ................................................................................................................. 7
4 Technical Information Summar ................................................................................. 8
5 Declaration of Conformit .......................................................................................... 9
5.1 Disposal of the camera ......................................................................................... 9
6 Warrant .................................................................................................................... 10
Page 2

1 Introduction
Congratulations on your purchase of an Atik Series 3 camera. This manual
will help you get the most out of your Atik camera: please take the time to
read it thoroughly, and you will be ready to discover new worlds.
Atik cameras provide e ceptional value for money, superior performance and
unrivalled ease of use. Our cameras are the result of e tensive research and
development, each one having been designed and built with the requirements
of the most demanding astro-imager in mind. Your Atik camera incorporates
state-of-the-art design and materials, and it will be your trusted astro-
photography companion for a long time to come.
Repairs, servicing and upgrades are available through your local dealer or at
http://www.atik-cameras.com.
Please note that modifications to the camera and or accessories which
are undertaken without the manufacturer’s written permission will void
the warranty, details of which are given at the back of this manual.
1.1 Further information
For installation instructions and other useful information please refer to the
quickstart guide which was shipped with the camera. Information on the
software is given in the ArtemisCapture guide, a PDF file of which is copied to
your computer hard drive by the software installer. Further information is
available on our website at http://www.atik-cameras.com.
Page 3

2 Pack Contents
This pack includes:
1. Atik Series 3 camera
2. USB cable
3. Car lighter type power cable
4. CD with software and manuals
5. Quick start guide
Page 4

3 Getting to know your camera
3.1 Camera Parts
1. ST-4 compatible autoguider port
2. 2.1mm centre-positive 12V DC input
3. 1.25” nosepiece with T2 (M42 0.75mm pitch) thread
4. USB port
Page 5

3.2 Sensor
The sensors used in the Atik series 3 cameras are listed below:
Black and White Colour
Atik 314L SONY ICX285AL SONY ICX285AQ
Atik 314E SONY ICX205AL SONY ICX205AQ
Atik 320E SONY ICX274AL SONY ICX274AQ
Due to the very clean nature of these CCDs, dark frames are unnecessary in
most cases. This is due to the low noise which stands at an amazing less than
5 electrons RMS.
3.3 Optical Window
The optical window used in front of the CCD is a BK7 with BBAR coatings on
both sides ensuring that no reflection will appear in your image.
3.4 Analog to igital Converter (A C)
The Analog to Digital Converter (ADC) is a 16-bit ADC. This means that your
Atik camera will allow you to record subtle levels of gray, providing you with
enhanced dynamic range when capturing an image.
3.5 Power Consumption
Your Atik camera was designed to have low power consumption: please see
the table in section 4 for details specific to your camera model. The 2.1mm
centre-positive DC input is compatible with a wide range of 12V DC supplies.
WARNING: If you have purchased the optional mains power adaptor, please
note that it is for indoor or observatory use only. There is a risk of electric
shock if the adaptor is used in damp environments or outside. If in doubt do not
use the adaptor and consult a trained electrician.
Page 6

3.6 USB Port
The Atik series 3 cameras use a USB 2.0 high-speed interface, allowing full-
frame image downloads in only a few seconds. A higher speed “preview”
mode is also present, providing roughly twice the speed.
3.7 Autoguiding Port
The autoguiding port enables you to do autoguiding with any ST4 compatible
guiding software when using the optional cable. The port schematics are
shown in section 4.
3.8 Cooling
Atik cameras are thermally stabilized to allow your CCD to output the best
result that it can deliver: please see the table in section 4 for details specific to
your camera model. After switching on the camera it is advisable to allow at
least 2 minutes before taking images, in order to allow the temperature to
stablilize. The very low readout noise, combined with efficient cooling, means
that dark frames are not necessary in most situations, allowing you to spend
more time imaging and less time taking calibration frames.
Page 7

4 Technical Information Summary
Atik 314L+ Atik 314E Atik320E
Sensor Type Sony ICX285 Sony ICX205 Sony ICX274
Resolution 1392 1040 pi els 1392 1040 pi els 1620 1220 pi els
Pixel Size 6.45 6.45μm 4.65 4.65μm 4.4 4.4μm
ADC 16 bit 16 bit 16 bit
Readout Noise (typical) 4 e-4 e-4 e-
Interface USB USB USB
Power 12V DC 0.8A 12V DC 0.55A 12V DC 0.8A
Maximum Exposure Unlimited Unlimited Unlimited
Minimum Exposure 1/1000 s 1/1000 s 1/1000s
Guide Port ST-4 compatible ST-4 compatible ST-4 compatible
Cooling Thermoelectric Thermoelectric Thermoelectric
Weight Appro . 400 g Appro . 350 g Appro . 350g
Backfocus distance 12mm 12mm 13mm
Autoguider port pinout
The following table gives the angular resolution per pi el with certain focal
distances. The formula to calculate any other focal length is:
(Pixel Size (μm) / Focal Distance (mm)) * 206.3 = angular resolution (arcseconds/ ixel)
Focal Distance (mm) Angular resolution
(arcsec/pi el) – 314L
Angular resolution
(arcsec/pi el) – 314E
350 3.80 2.74
400 3.33 2.40
450 2.96 2.13
500 2.66 1.92
550 2.42 1.74
600 2.22 1.60
650 2.05 1.48
700 1.90 1.37
750 1.77 1.28
800 1.66 1.20
850 1.57 1.13
900 1.48 1.07
950 1.40 1.01
1000 1.33 0.96
Page 8

5 Declaration of Conformity
EU Declaration of Conformity.
This product carries the CE Mark in accordance with the related European Directive. CE
Marking is the responsibility of:
Perseu, A
R. Dr. Agostinho Neto, 1D
2690-576 ta Iria da Azoia
Portugal
Critical Applications.
This product is not designed for any “critical applications”. “Critical applications” means life
support systems, medical applications , connections to medical devices, commercial
transportations, nuclear facilities or systems or any other applications where product failure
could lead to injury to persons or loss of life or catastrophic property damage.
This product is not a toy.
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
5.1 isposal of the camera
When no longer required do not dispose of this electronic device with general
household waste. To minimise pollution and protect the environment the camera
should be rec cled. Local rec cling drop off points available under the Waste from
Electrical and Electronic Equipment (WEEE) regulations which will accept the
camera. For further information contact Perseu SA at the above address, or the shop
from which the camera was bought.
Page 9

6 Warranty
The equipment is guaranteed against defective design, manufacture or
materials for a period of one year from the date of purchase.
This means that Atik Cameras will repair or replace the equipment at its sole
option, at no charge to the purchaser for parts or for labour, if the fault is
reported within the guarantee period, provided however that Atik Cameras is
able to duplicate the defect or problem at its facilities. This warranty does not
apply to damage that occurred as a result of abuse or misuse, abnormal
service or handling, damage which may have been caused either directly or
indirectly by another product, or if the equipment has been altered or modified
in any way, or if the damage was caused by repairs or service provided or
attempted by anyone other than Atik Cameras. This warranty does not include
or provide for incidental or consequential damages.
To e ercise your rights under this warranty, you must return the equipment to
the dealer from whom it was purchased together with proof of purchase and a
clear description of the fault. If it’s not possible to return the equipment to your
dealer, you should contact Atik Cameras. Equipment returned to Atik
Cameras must be sent in appropriate packaging and at your e pense
(insurance is recommended), together with proof of purchase, a return
address and a clear description of the fault.
This does not affect your statutory rights.
Page 10