Atlantis Land A02-RB-W54 User manual

Where solutions begin
Company certified ISO 9001:2000
Wireless Broadband
Router
A02-RB-W54
USER GUIDE
A02-RB-W54(V1.1) _ME01

Where solutions begin
Company certified ISO 9001:2000

Wireless Broadband Router
INDEX
CHAPTER 1: INTRODUCTION 1
1.1 An Overview of the del Wireless Broadband Router 1
1.2 Package Contents 2
1.3 Technical Features 2
1.4 System Requirements 3
1.5 Setup 3
CHAPTER 2: USING WIRELESS BROADBAND ROUTER 4
2.1 Cautions for using the Wireless Broadband Router 4
2.2 The Front LEDs 4
2.3 The Rear Ports 5
2.4 Cabling 6
CHAPTER 3: CONFIGURATION 8
3.1 Before Configuration 8
3.1.1 Windows 95/98/ME 9
3.1.2 Windows NT4.0 10
3.1.3 Windows 2000 11
3.1.4 Windows XP 12
3.2 Factory Default Settings 13
3.2.1 Password 13
3.2.2 LAN and WLAN Ports 13
3.3 Accessing the Wireless Broadband Router Web Configurator 14
3.3.1 Setup Wizard 15
3.3.2 Navigating the Broadband Router Web Configurator 28
3.4 WAN 29
3.4.1 Connection Type 29
3.4.2 Dynamic DNS 34
3.5 Wireless 35
3.5.1 Basic 35
3.5.2 Security 36
3.5.3 Advanced 39
3.6 LAN 40

Wireless Broadband Router
3.6.1 Basic 40
3.6.2 DHCP 41
3.7 Access Control 42
3.7.1 Filter 42
3.7.1.2 MAC Filter 43
3.7.1.3 IP Filter 45
3.7.1.4 URL Blocking 46
3.7.1.5 Domain Blocking 47
3.7.1.6 Protocol Filter 48
3.7.2 Virtual Server 49
3.7.3 Special AP 52
3.7.4 DMZ 53
3.7.5 Firewall Rule 54
3.8 System 56
3.8.1 Password 56
3.8.2 Time 57
3.8.3 Device Information 58
3.8.4 Log 60
3.8.5 Log Settings 61
3.8.6 Statistics 62
3.8.7 Restart 64
3.8.8 Firmware 64
3.8.9 Configuration 65
3.8.10 UPnP 66
3.8.11 Ping Test 66
3.8.12 Remote Management 67
APPENDIX A: TROUBLESHOOTING 69
A.1 LEDs 69
A.1.1 LED Power 69
A.1.2 LED LAN 69
A.1.3 LED WLAN 70
A.2 WEB 70
A.3 Login 71
A.4 Remote Management 71
A.5 FAQ 72
APPENDIX B: REGULATIONS 77

Wireless Broadband Router
APPENDICE C: TECHNICAL FEATURES 78
APPENDICE D: SUPPORT 79
A02-RB-W54(V1.1)_ME01 (V1.0 January 2007)

Wireless Broadband Router
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording or otherwise without the prior writing of the publisher.
Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp. Pentium is
trademark of Intel. All copyright reserved.
The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other
names mentioned mat be trademarks or registered trademarks of their respective
owners. Subject to change without notice. No liability for technical errors and/or
omissions.
Wireless LAN, Health and Authorization for use
Radio frequency electromagnetic energy is emitted from Wireless LAN devices.
The energy levels of these emissions however are far much less than the
electromagnetic energy emissions from wireless devices like for example mobile
phones. Wireless LAN devices are safe for use frequency safety standards and
recommendations. The use of Wireless LAN devices may be restricted in some
situations or environments for example:
·On board of airplanes, or
·In an explosive environment, or
·In case the interference risk to other devices or services is perceived or identified
as harmful
In case the policy regarding the use of Wireless LAN devices in specific
organizations or environments (e.g. airports, hospitals, chemical/oil/gas industrial
plants, private buildings etc.) is not clear, please ask for authorization to use
these devices prior to operating the equipment.
Regulatory Information/disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with
the instructions included in the user documentation provided with the product. Any
changes or modifications made to this device that are not expressly approved by
the manufacturer may void the user’s authority to operate the equipment. The
Manufacturer is not responsible for any radio or television interference caused by
unauthorized modification of this device, of the substitution or attachment.
Manufacturer and its authorized resellers or distributors will assume no liability for
any damage or violation of government regulations arising from failing to comply
with these guidelines.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
CE in which Countries where the product may be used freely:

Wireless Broadband Router
Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland,
Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland.
France: except the channel 10 through 13, law prohibits the use of other
channels.
CE/EMC Restriction of Liability
The product described in this handbook was designed, produced and approved
according to the EMC-regulations and is certified to be within EMC limitations.
If the product is used in an uncertified PC, the manufacturer undertakes no
warranty in respect to the EMC limits. The described product in this handbook
was constructed, produced and certified so that the measured values are within
EMC limitations. In practice and under special circumstances, it may be possible,
that the product may be outside of the given limits if it is used in a PC that is not
produced under EMC certification. It is also possible in certain cases and under
special circumstances, which the given EMC peak values will become out of
tolerance. In these cases, the user himself is responsible for compliance with the
EMC limits.
Declaration of Conformity
This equipment has been tested and found to comply with Directive 1999/5/CE of
the European Parliament and of the Council on radio equipment and
telecommunications terminal equipment and the mutual recognition of their
conformity. After assessment, the equipment has been found to comply with the
following standards: EN 300.328 (radio), EN 301 489-1, EN 301 489-17
(electromagnetic compatibility) and EN 60950 (safety). This equipment may be
used in all European Union contries and in all countries applying Directive
1999/5/CE, without restriction, with the exception of the following countries:
France:When this equipment is used outdoors, output power is limited to within
the frequency bans listed on the chart. For more info, consult the website
www.art-telecom.fr.
Location Frequency Band
(MHz)
Power (EIRP)
Indoor (no restriction) 2400-2483,5 100mW(20dBm)
Outdoor 2400-2454
2454-2483,5
100mW(20dBm)
10mW(10dBm)
Italy: For more info, consult the website www.comunicazioni.it

Wireless Broadband Router
A02-RB-W54 Pag. 1
CHAPTER 1: Introduction
Congratulations on your purchase of Atlantis Land Wireless Broadband Router.
This integrated access device combines Internet gateway functions with wireless
LAN and Fast Ethernet switch. It provides a complete solution for Internet surfing
and office resources sharing, and it is easy to configure and operate for every
users.
This manual discusses how to install the IEEE 802.11g Wireless Broadband
Router.
1.1 An Overview of the del Wireless Broadband Router
With the explosive growth of the Internet, accessing information and services at
any time, day or night has become a standard requirement for most people. The
era of the standalone PC is waning. Networking technology is moving out of the
exclusive domain of corporations and into homes with at least two computers.
This integrated access device combines Internet gateway functions with wireless
LAN and Fast Ethernet switch. Designed for the business and home, it saves you
the cost of installing a separate modem and ISP line for each computer, while
providing ready connection for the users, with or without the network wires.
Broadband network access is also gaining ground. However, allowing more than
two computers to access the Internet at the same time means less affordable,
higher costs. Thus, there is a need to share one legal IP address over a single
Internet connection to link the home with the Internet.
The scarcity of IP addresses and using a shared Internet connection through an
Internet sharing device can solve high network access costs. All linked computers
can make full use of broadband capabilities over such a device.
This device not only comes equipped with a wide range of features, but also can
be installed and configured right out of the box. This device supports a simple
local area network and Internet access share, offering great cost savings.
The local area network connects up home computers while also allowing any of
the computers to access the Internet, share resources, or play online games—the
basis of the family computing lifestyle.

Wireless Broadband Router
A02-RB-W54 Pag. 2
1.2 Package Contents
Unpack the package and check all the items carefully. If any item contained is
damaged or missing, please contact your local dealer as soon as possible. Also,
keep the box and packing materials in case you need to ship the unit in the future.
The package should contain the following items:
•Wireless Broadband Router
•2 dBi Antenna
•CDRom with online manual
•Quick Start Guide (English, French, Italian)
•AC/DC power adapter (7.5 V, 1A)
1.3 Technical Features
Wireless Broadband Router provides the following features:
•Compliant with IEEE 802.11g and 802.11b Devices
•Built-in 4 x 10/100Mbps Auto-MDIX LAN Ports
•Built-in 1 x 10/100Mbps Auto-MDIX WAN Port (Internet)
•Supports Cable/DSL Modems with Dynamic IP, Static IP, PPPoE, L2TP,
PPTP or BigPond Connection Types
•DHCP Server Feature Allocates up to 253 Client IP Addresses
•Supports 64/128-bit Wired Equivalent Privacy (WEP)
•Supports WPA, WPA2, WPA-PSK and WPA2-PSK Advanced Security
•Supports MAC Address, Protocol Filters and UPnP (Universal Plug &
Play)
•Traffic Control with Virtual Server, Virtual PC mapping and DMZ
•Provides Additional Security with SPI / NAT firewall and Attack Alert via
emails
•Provides Additional Security of Enable/Disable SSID, Password
Protection
•Flash Memory for Firmware Upgrade, Save/Restore Settings, and Traffic
Log
•Compliant with Windows 95/98/NT/2000/XP, Linux and Mac OS
•Easy Management and Remote Management via Web Browser (HTTP)
•Range for Indoor of 30 ~ 50 meters (depends on the environment)
•Range for Outdoor of 50 ~ 200 meters (depends on the environment)

Wireless Broadband Router
A02-RB-W54 Pag. 3
1.4 System Requirements
Before installing the device, your PC should meet the following:
•Intel® Pentium®III 600Mhz or compatible processor with TCP/IP stack
•Iinternet Explorer V6.0 on Netscape V6.0
•CDRom
1.5 Setup
The setup of the Wireless Broadband Router can be performed properly using the
following methods:
•The power outlet should be within 1.82 meters (6 feet) of the Broadband
Router.
•Visually inspect the DC power jack and make sure that it is fully secured
to the power adapter.
•Make sure that there is proper heat dissipation from and adequate
ventilation around the Broadband Router. Do not place heavy objects on
the Broadband Router.
Fix the direction of the antennas. Try to place the Wireless Router in a position
that can best cover your wireless network. Normally, the higher you place the
antenna, the better the performance will be. The antenna’s position enhances the
receiving
sensitivity.

Wireless Broadband Router
A02-RB-W54 Pag. 4
CHAPTER 2: Using Wireless Broadband Router
2.1 Cautions for using the Wireless Broadband Router
•Do not place this device under high humidity and high temperature.
•Do not use the same power source for Wireless Broadband Router with
other equipment.
•Do not open or repair the case yourself. If the Wireless Broadband
Router is too hot, turn off the power immediately and have a qualified
serviceman repair it.
•Place the Wireless Broadband Router on a stable surface.
•Only use the power adapter that comes with the package.
•Do NOT upgrade firmware on any Atlantis Land product over a wireless
connection. Failure of the device may result. Use only hard-wired network
connections.
2.2 The Front LEDs
LED MEANING
POWER This indicator lights green when the hub is receives power,
otherwise it is off.
STATUS
This indicator blinks green means the Internet Broadband
Router is working successful. Otherwise, this indicator always
on or off means the function of the Internet Broadband Router is
fail.
WAN The indicators light green when the WAN port was connected to
an xDSL/Cable modem successfully.

Wireless Broadband Router
A02-RB-W54 Pag. 5
The indicators blink green while the WAN port was transmitting
or receiving data on the xDSL/Cable modem.
WLAN This indicator lights green when there are wireless devices
connected and transmitting data to the Wireless Router.
LAN (1-4)
These indicators light green when the LAN ports were
connected successfully.
These indicators blink green while the LAN ports were
transmitting data.
2.3 The Rear Ports
PORT USAGE
POWER Jack(2)
Plug the power adapter to this power jack
WAN(3) In the four port broadband router, there is an RJ-45
10/100Mbps Auto-MDIX port for the WAN that will fit
the xDSL/Cable modem’s specification need.
LAN(4) Four RJ-45 10/100Mbps Auto-MDIX ports for
connecting to either 10Mbps or 100Mbps Ethernet
connections.
Reverse SMA(5) There are one 2 dBi Gain Antenna in the rear panel for
wireless connection.
Reset(1) After the device has turned on, press it to reset the
device or restore to factory default settings. Use a pin-

Wireless Broadband Router
A02-RB-W54 Pag. 6
shape item to push to reset this device to factory
default settings. It will be useful too when the manager
forgot the password to login, but the setting will be
back to default setting.
2.4 Cabling
Plug in one end of the network cable to the WAN port of the Wireless Internet
Broadband Router.
Plug in the other end of the network cable to the Ethernet port of the xDSL or
Cable modem (E.G A02-RA141 or A02-RA111).
Use another network cable to connect to the Ethernet card on the computer
system; the other end of the cable connects to the LAN port of the Internet
Broadband Router. Since the Wireless Broadband Router has four ports, you can
connect up to four computers directly to the unit. There you do not have to buy a
switch to connect these computers since one Internet Broadband Router
functions both as a connection-sharing unit and as a switch.
The control LEDs of the Wireless Internet Broadband Router are clearly visible
and the status of the network link can be seen instantly:
•With the power source on, once the device is connected to the broadband
modem, the Power, LAN, WLAN and WAN port link LEDs of the Internet
Broadband Router will light up indicating a normal status. Led Status
blinks.
•While the WAN is link up to the ADSL/Cable modem, the WAN port’s
Link/ACT LED will light up.
•While the LAN is link up to the computer system, the LAN port’s Link/ACT
LED will light up.

Wireless Broadband Router
A02-RB-W54 Pag. 7

Wireless Broadband Router
A02-RB-W54 Pag. 8
CHAPTER 3: Configuration
The Wireless Broadband Router has a Web GUI interface for the configuration.
The device can be configured through the Web Browser. A network manager can
manage, control and monitor the Router from the local LAN. This section
indicates how to configure the AP to enable its functions.
3.1 Before Configuration
This section describes the configuration required by LAN-attached PCs that
communicate with the Wireless Broadband Wireless , either to configure the
device or for network access. These PCs must have an Ethernet interface
installed properly, be connected to the Router either directly or through an
external repeater hub, and have TCP/IP installed and configured to obtain an IP
address through a DHCP server or a fixed IP address that must be in the same
subnet of the Wireless Broadband Router. The default IP address of the Wireless
Broadband Router is 192.168.1.1 and subnet mask is 255.255.255.0. The best
and easy way is to configure the PC to get an IP address from the Wireless
Broadband Router. Also make sure you have UNINSTALLED any kind of
software firewall that can cause problems while accessing the 192.168.1.1 IP
address of the router.
Please follow the steps below for PC’s network environment installation. First of
all, please check your PC’s network components. The TCP/IP protocol stack and
Ethernet network adapter must be installed. If not, please refer to MS Windows
related manuals.
Any TCP/IP capable workstation can be used to communicate
with or through the Wireless Broadband Router to configure
other types of workstations, please consult the manufacturer’s
documentation.

Wireless Broadband Router
A02-RB-W54 Pag. 9
3.1.1 Windows 95/98/ME
1. Go to Start / Settings / Control
Panel. In the Control Panel,
double-click on Network and
choose the Configuration tab.
2. Select TCP / IP -> NE2000
Compatible, or the name of any
Network Interface Card (NIC) in
your PC.
3. Click Properties.
4. Select the IP Address tab. In
this page, click the Obtain an IP
address automatically radio
button.

Wireless Broadband Router
A02-RB-W54 Pag. 10
3.1.2 Windows NT4.0
1. Go to Start / Settings / Control
Panel. In the Control Panel, double-
click on Network and choose the
Protocols tab.
2. Select TCP/IP Protocol and click
Properties.
3. Select the Obtain an IP address
from a DHCP server radio button
and click OK.

Wireless Broadband Router
A02-RB-W54 Pag. 11
3.1.3 Windows 2000
1. Go to Start / Settings / Control
Panel. In the Control Panel,
double-click on Network and
Dial-up Connections.
2. Double-click LAN Area
Connection.
3. In the LAN Area Connection
Status window, click Properties.
4. Select the Obtain an IP address
automatically and the Obtain
DNS server address
automatically radio buttons.).
5. Click OK to finish the
configuration.

Wireless Broadband Router
A02-RB-W54 Pag. 12
3.1.4 Windows XP
1. Go to Start / Control
Panel (in Classic View). In
the Control Panel, double-
click on Network
Connections.
2. Double-click Local Area
Connection
3. In the LAN Area
Connection Status window,
click Properties.
4. Select Internet Protocol
(TCP/IP) and click
Properties.
5. Select the Obtain an IP
address automatically
and the Obtain DNS
server address
automatically radio
buttons
6. Click OK to finish the
configuration.

Wireless Broadband Router
A02-RB-W54 Pag. 13
3.2 Factory Default Settings
Before configuring the Wireless Broadband Router through WLAN, make sure
that the SSID, Channel and the WEP was set properly.
The default setting of the Wireless Broadband Router that you will use:
•User: admin
•Password: admin
•IP Address: 192.168.1.1
•Subnet Mask: 255.255.255.0
•DHCP Server: enable (192.168.1.100-192.168.1.199)
•Wep Encryption: disable
•SSSID: default
•Channel: 6
3.2.1 Password
When there is a screen needs to enter the Network password, it means that there
is a password settle, type in the password you entered before.
3.2.2 LAN and WLAN Ports
The parameters of LAN and WLAN ports are pre-set in the factory. The default
values are shown below.
LAN WLAN
IP address 192.168.1.1
Subnet Mask 255.255.255.0
Channel=6
SSID=default
Encryption=none